Skip to content

Electricity simulation

Circuit Builder Simulation

Build any circuit you like with cells, lamps, resistors, switches, meters, diodes, LDRs and thermistors. Watch the current flow, read the meters, and test the rules for series and parallel circuits.

Loading simulation…
Show symbols for

Predict first

Question 1 of 3

Two identical lamps are connected in series with a battery. How does the current through the second lamp compare with the current through the first?

Try this

  1. 1Load the Series circuit. Move the ammeter to three different places in the loop. Does the reading change?
  2. 2Load the Parallel circuit and add a third lamp on a new branch. Watch the ammeter next to the battery.
  3. 3Select a lamp and read its resistance. Increase the battery's e.m.f. and read it again. Why has it changed?
  4. 4Load the Diode circuit and press Turn round on the diode. What happens to the current?
  5. 5Load the LDR divider and move the light slider. When is the voltmeter reading biggest?

What this simulation shows

Build a circuit on the grid, and the simulation works out the current through every part and the potential difference (p.d.) across it. Lamps glow more brightly when they transfer more power, LEDs light up when they conduct, and moving dots show the current. Choose whether the dots show conventional current, from positive to negative, or the electrons, which flow the opposite way.

How to build a circuit

Pick a part from the toolbar, then tap a gap between two dots to place it. Every part, including a plain wire, joins two neighbouring dots. A circuit only works if there is a complete loop from one terminal of the battery back to the other. Choose Select and tap a part to see its readings, change its value or turn it round. On a keyboard, focus the circuit and use the arrow keys, O to turn the cursor and Enter to place.

Current and potential difference

Current is the rate of flow of charge, measured in amperes with an ammeter placed in series. Potential difference is the energy transferred per unit of charge, measured in volts with a voltmeter placed across a component. The simulation's meters behave like good real ones: the ammeter has almost no resistance and the voltmeter has a very high resistance.

The current through a component depends on the p.d. across it and its resistance:

V=IRV = IR

Series and parallel

In a series circuit there is one loop. The current is the same everywhere, and the p.d.s across the components add up to the supply p.d. In a parallel circuit each branch connects across the same two points. Every branch has the full p.d., and the branch currents add up to the current from the supply. Use the starting circuits to check each rule with the meters.

Components to explore

  • Filament lamp: its resistance rises as it gets hotter, so its I–V graph curves.
  • Diode and LED: current flows one way only, once the p.d. is above a small threshold. An LED needs a resistor in series to limit the current.
  • LDR: resistance falls as the light gets brighter.
  • Thermistor: resistance falls as the temperature rises.
  • Fuse: breaks the circuit if the current goes above its rating.

Short circuits

If you join a battery's terminals with just a wire, a huge current flows. The simulation warns you when this happens. Real cells have a small internal resistance, which the simulation includes, so you may see readings very slightly below the ideal values.

Symbols in your course

The simulation uses the symbols in UK and international syllabuses. US courses often draw a resistor as a zigzag instead of a rectangle; the physics is the same.

Equations

Check your understanding

8 questions

  1. 1.How should an ammeter be connected to measure the current through a lamp?
  2. 2.How should a voltmeter be connected to measure the p.d. across a resistor?
  3. 3.Two identical lamps are in series with a 6 V battery. What is the p.d. across each lamp?
  4. 4.Two identical lamps are in parallel with a 6 V battery. What is the p.d. across each lamp?
  5. 5.A 12 V battery is connected to a 4 Ω resistor. What current flows?
  6. 6.Why does the resistance of a filament lamp increase as the current increases?
  7. 7.What happens to the resistance of an LDR when the light gets brighter?
  8. 8.What is the job of a fuse in a circuit?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more