Resistance of a Wire Practical: Length, Thickness and the R–L Graph
Investigate how the resistance of a wire depends on its length: the circuit, the method, R = V/I for each length, the straight-line graph and its small intercept, why the current must stay small, and how a thicker wire changes the result. With worked examples and typical values.
Published · 8 min read
On this page
The resistance of a metal wire is directly proportional to its length, as long as its temperature does not change. Double the length, and the resistance doubles too. In the practical, you clip onto different lengths of a thin wire. For each length, you measure the current through it and the p.d. across it, then work out .
Plotted against length, the resistance should give a straight line through the origin. Real results often cut the resistance axis slightly above zero, because the clips and their contacts add a little resistance of their own. A thicker wire made of the same metal has a lower resistance.
Why does a longer wire have more resistance?
In a metal, the current is a drift of free electrons. On their way, they keep colliding with the metal ions, which vibrate about fixed places. Every extra centimetre of wire means more collisions. Two equal pieces joined end to end behave like two equal resistors in series, so their resistances add.
Thickness works the opposite way. A thick wire is like several thin wires laid side by side, which is a parallel arrangement. More paths share the current, so the total resistance is smaller.
What apparatus do you need?
- a thin wire, often constantan, taped straight along a metre rule
- a low-voltage supply or a cell, and a switch
- an ammeter, in series with the wire
- a voltmeter, connected to the two crocodile clips
- a fixed resistor or variable resistor in series, to keep the current small
- a micrometer, if you also test thickness
Constantan is popular because its resistance barely changes as it warms. A thin piece also has a few ohms per metre, which is easy to measure. Copper of the same thickness has nearly thirty times less resistance, so its p.d. readings would be tiny.
What is the method, step by step?
- Stretch the wire along the metre rule with no kinks, and tape it down at both ends.
- Fix one crocodile clip at the 0 cm mark. Connect the supply, switch, ammeter and series resistor to this clip, and return the circuit from a second clip that you can slide along the wire.
- Attach the voltmeter's leads to the two clips. It then reads the p.d. across just the length of wire between them.
- Put the sliding clip at 20 cm. Close the switch, read both meters quickly, then open the switch.
- Move the clip in 20 cm steps up to 100 cm, taking readings at each position.
- Repeat the whole set twice more and find a mean resistance for each length.
- Plot resistance on the y-axis against length on the x-axis.
Measure every length from the fixed clip, not from the end of the wire.
Worked example 1: the resistance at one length
A student in Accra sets the clips 60 cm apart. The voltmeter reads 0.74 V and the ammeter reads 0.20 A. Find the resistance of that length of wire.
Given: V = 0.74 V, I = 0.20 A
Equation:
Substitution:
Answer: R = 3.7 Ω
What should the graph of R against L look like?
Here is a typical set of mean results for a constantan wire about 0.32 mm across.
| Length / m | Mean resistance / Ω |
|---|---|
| 0.20 | 1.30 |
| 0.40 | 2.50 |
| 0.60 | 3.70 |
| 0.80 | 4.90 |
| 1.00 | 6.10 |
Each extra 0.20 m adds the same 1.20 Ω, so the points lie on a straight line. Its gradient is the resistance of each metre of wire. A wire of zero length would have no resistance at all, so in theory the line should pass through the origin.
If you extend the line back to zero length, it meets the resistance axis at about 0.10 Ω, not at zero. There are two common reasons:
- Contact resistance. The clips grip the wire at small points, and those joints add a fixed extra resistance to every reading.
- A zero error. If the fixed clip is not exactly on the 0 cm mark, every length is wrong by the same amount, which shifts the whole line up or down.
Both are systematic errors. They move the line but leave its gradient unchanged, so the gradient still gives a reliable resistance per metre. Fit the best straight line to your points, and don't force it through the origin.
Worked example 2: using the gradient
The line through the results above passes through (0, 0.10 Ω) and (1.00 m, 6.10 Ω). Find the resistance per metre. Then find the length of this wire that has a resistance of 3.0 Ω, ignoring the clips.
Gradient: Ω per metre
Length:
Answer: each metre has a resistance of 6.0 Ω, so the length is 0.50 m.
Why must the current stay small?
A current heats the wire. In most metals, a hotter wire has a higher resistance, so a warm wire gives readings that are too high, and the points no longer lie on a straight line. That is why the practical asks for a constant temperature.
- Switch off between readings, so the wire has time to cool.
- Keep the current to a few tenths of an ampere, using a low supply p.d. or the series resistor.
- Avoid very short lengths. Their resistance is so small that the current can become large.
A thin wire carrying a big current can get hot enough to burn you, and it stays hot for a short time after you open the switch. Let it cool before you touch it.
How does the thickness of the wire change its resistance?
For wires of the same metal and length, resistance is inversely proportional to the cross-sectional area. Twice the area means half the resistance.
Be careful with diameter. The area grows with the square of the diameter: a wire twice as wide has four times the area, and only a quarter of the resistance. Measure the diameter with a micrometer at several points along the wire, in two directions at right angles at each point, and take a mean. Our guide to vernier calipers and micrometers shows how to read one.
Worked example 3: a thicker wire
A class in Lahore repeats the practical with a constantan wire 0.38 mm across instead of 0.32 mm. Predict its resistance per metre, using 6.0 Ω per metre for the thinner wire.
Area ratio: , so the thicker wire has 1.41 times the area
Resistance per metre: Ω per metre
Answer: about 4.3 Ω per metre. The wire is only about 19% wider, but its resistance falls by about 29%.
To practise the meter connections, open the circuit builder and choose Empty. Join the battery, an ammeter and a resistor into a single loop, then connect a voltmeter to both ends of the resistor. Choose Select, tap the resistor, and set it to 2 Ω, then 4 Ω, then 6 Ω, like clipping onto longer and longer pieces of one wire. Each time, the voltmeter reading divided by the ammeter reading gives back the value you set. You can also explore the resistance of a wire simulation.
Common mistakes
- Connecting the voltmeter across the supply. It must measure only the length of wire between the clips.
- Leaving the switch closed. The wire warms up, and later readings come out too high.
- Forcing the line through the origin. Draw the best fit and explain any intercept.
- Halving the resistance when the diameter doubles. Area goes up four times, so the resistance falls to a quarter.
- Measuring from the end of the wire. Measure from the fixed clip.
- Calling contact resistance a random error. It shifts every reading by the same amount, which makes it a systematic error.
Key points
- A wire's resistance is directly proportional to its length, provided its temperature stays constant.
- Find for each length, then plot resistance against length.
- The graph is a straight line. Its gradient is the resistance per metre, and a small intercept usually comes from contact resistance or a zero error.
- Use a small current and open the switch after each reading, to stop the wire heating up.
- A thicker wire of the same metal has less resistance. Resistance is inversely proportional to the cross-sectional area, which depends on the diameter squared.