Skip to content

Series and Parallel Circuits: Rules for Current, Voltage and Resistance

Learn the current and potential difference rules for series and parallel circuits, how to find total resistance, and why adding a parallel branch lowers it.

Published · 6 min read

On this page

In a series circuit, the components are joined one after another in a single loop. In a parallel circuit, each component sits on its own branch. The rules for current, potential difference and resistance are different in each type.

Here are the rules in brief:

  • Series: the current is the same everywhere. The potential differences across the components add up to the supply p.d. Total resistance is the sum of the resistances.
  • Parallel: the potential difference across each branch is the same. The branch currents add up to the total current. Total resistance is less than the smallest single resistance.

The rest of this guide explains why these rules are true and shows how to use them in calculations.

What is the difference between series and parallel circuits?

In a series circuit there is only one path for the charge. If one component breaks, the whole circuit stops working. Some older strings of decorative lights, like those used at Diwali or Christmas, are wired this way: when one bulb fails, they all go out.

In a parallel circuit there are several paths. Each branch connects across the same two points. If one branch breaks, the others keep working. The lights and sockets in a home are wired in parallel. That way, each appliance gets the full mains p.d. and can be switched on and off by itself.

Series and parallel at a glance

QuantitySeriesParallel
CurrentSame everywhereSplits between branches; branch currents add to the total
Potential differenceShared; p.d.s add to the supply p.d.Same across each branch
Total resistanceRT=R1+R2R_T = R_1 + R_2Less than the smallest resistor
If one part breaksEverything stopsOther branches keep working

Current in series and parallel circuits

Current is the rate of flow of charge. It is measured in amperes (A) with an ammeter connected in series.

Series: the current is the same everywhere

There is only one path, so the same charge passes every point each second. An ammeter placed anywhere in a series loop gives the same reading.

Current is not "used up" by a lamp or resistor. The charge keeps flowing round. What the components take is energy.

Parallel: the current splits and rejoins

At a junction, the current divides between the branches. It joins back together where the branches meet again. Charge is never created or destroyed, so:

I=I1+I2+I3+…I = I_1 + I_2 + I_3 + \dots

A branch with a smaller resistance carries a bigger current.

Potential difference in series and parallel circuits

Potential difference is measured with a voltmeter connected in parallel, across the component.

Series: the supply p.d. is shared

The energy given to the charge by the supply is shared between the components. So the p.d.s add up to the supply p.d.:

V=V1+V2+V3+…V = V_1 + V_2 + V_3 + \dots

The current is the same through each component, and V=IRV = IR. So the component with the biggest resistance gets the biggest share of the p.d.

Parallel: each branch has the same p.d.

Each branch connects across the same two points. So each branch has the same p.d. If the branches are connected straight across the supply, each one has the full supply p.d.

How do you calculate total resistance?

Resistors in series

RT=R1+R2+R3+…R_T = R_1 + R_2 + R_3 + \dots

The charge must pass through every resistor in turn. Each one adds to the total. Adding a resistor in series always increases the total resistance.

Resistors in parallel

1RT=1R1+1R2+1R3+…\frac{1}{R_T} = \frac{1}{R_1} + \frac{1}{R_2} + \frac{1}{R_3} + \dots

Two shortcuts are useful:

  • For two resistors only: RT=R1R2R1+R2R_T = \dfrac{R_1 R_2}{R_1 + R_2}
  • For n identical resistors, each of resistance R: RT=RnR_T = \dfrac{R}{n}

Some books write RTR_T as RtotalR_{\text{total}} or call it the equivalent resistance, ReqR_{\text{eq}}. They all mean the same thing.

Why does adding a resistor in parallel lower the total resistance?

This surprises many students. You are adding a resistor, yet the total resistance goes down. Here is why.

  1. A new parallel branch gives the charge an extra path.
  2. The p.d. across the old branches does not change, so their currents do not change.
  3. The new branch carries its own current, in addition to the old ones.
  4. So the total current from the supply goes up.
  5. The supply p.d. is the same, and R=VIR = \dfrac{V}{I}. A bigger current for the same p.d. means a smaller total resistance.

Think of the ticket gates at a busy metro station in Delhi or London. Opening one more gate does not make any gate wider. But more people get through every second, so the crowd moves more easily.

To see this happen, open the series and parallel rules simulation. Compare the ammeter and voltmeter readings with one branch and with two, and check each rule in this guide for yourself.

Worked examples

Worked example 1: a series circuit

A 12 V battery is connected in series with a 4.0 Ω resistor and a 2.0 Ω resistor. Find the current and the p.d. across each resistor.

Total resistance: RT=4.0+2.0=6.0 ΩR_T = 4.0 + 2.0 = 6.0\ \Omega

Given: V = 12 V, RT=6.0 ΩR_T = 6.0\ \Omega

Equation: I=VRI = \dfrac{V}{R}

Substitution: I=126.0I = \dfrac{12}{6.0}

Answer: I = 2.0 A, the same through both resistors.

P.d. across each resistor, using V=IRV = IR:

  • 4.0 Ω resistor: V=2.0×4.0=8.0 VV = 2.0 \times 4.0 = 8.0\ \text{V}
  • 2.0 Ω resistor: V=2.0×2.0=4.0 VV = 2.0 \times 2.0 = 4.0\ \text{V}

Check: 8.0 V + 4.0 V = 12 V, which equals the supply p.d.

Worked example 2: a parallel circuit

A 6.0 V battery is connected across a 3.0 Ω resistor and a 6.0 Ω resistor in parallel. Find each branch current, the total current and the total resistance.

Given: each branch has the full 6.0 V across it.

Branch currents, using I=VRI = \dfrac{V}{R}:

  • 3.0 Ω branch: I1=6.03.0=2.0 AI_1 = \dfrac{6.0}{3.0} = 2.0\ \text{A}
  • 6.0 Ω branch: I2=6.06.0=1.0 AI_2 = \dfrac{6.0}{6.0} = 1.0\ \text{A}

Total current: I = 2.0 + 1.0 = 3.0 A

Total resistance:

1RT=13.0+16.0=0.50\frac{1}{R_T} = \frac{1}{3.0} + \frac{1}{6.0} = 0.50

Answer: RT=10.50=2.0 ΩR_T = \dfrac{1}{0.50} = 2.0\ \Omega

Check: VI=6.03.0=2.0 Ω\dfrac{V}{I} = \dfrac{6.0}{3.0} = 2.0\ \Omega. Notice that 2.0 Ω is less than the smallest resistor, 3.0 Ω.

Now add a third branch: another 6.0 Ω resistor. It carries 1.0 A, so the total current becomes 4.0 A. The total resistance falls to 6.04.0=1.5 Ω\dfrac{6.0}{4.0} = 1.5\ \Omega. This is the rule from the section above, in numbers.

Worked example 3: a combined circuit

A 12 V supply is connected to a 4.0 Ω resistor in series with a parallel pair: 6.0 Ω and 12 Ω. Find the current from the supply and the current in each parallel branch.

Step 1, the parallel pair: RP=6.0×126.0+12=7218=4.0 ΩR_P = \dfrac{6.0 \times 12}{6.0 + 12} = \dfrac{72}{18} = 4.0\ \Omega

Step 2, the total resistance: RT=4.0+4.0=8.0 ΩR_T = 4.0 + 4.0 = 8.0\ \Omega

Step 3, the supply current: I=VRT=128.0=1.5 AI = \dfrac{V}{R_T} = \dfrac{12}{8.0} = 1.5\ \text{A}

Step 4, the p.d.s: across the 4.0 Ω resistor, V=1.5×4.0=6.0 VV = 1.5 \times 4.0 = 6.0\ \text{V}. The rest of the supply p.d., 12 − 6.0 = 6.0 V, is across the parallel pair.

Step 5, the branch currents:

  • 6.0 Ω branch: 6.06.0=1.0 A\dfrac{6.0}{6.0} = 1.0\ \text{A}
  • 12 Ω branch: 6.012=0.50 A\dfrac{6.0}{12} = 0.50\ \text{A}

Check: 1.0 A + 0.50 A = 1.5 A, which matches the supply current.

Try building this circuit in the circuit builder and placing ammeters and voltmeters yourself. The simulated cells have a tiny internal resistance, so readings may differ very slightly from these ideal answers.

Common mistakes

  • Thinking current gets used up. In a series circuit the current is the same before and after each component.
  • Adding parallel resistances directly. 3.0 Ω and 6.0 Ω in parallel is 2.0 Ω, not 9.0 Ω.
  • Forgetting the last step. Adding the reciprocals gives 1RT\dfrac{1}{R_T}. You must take the reciprocal again to get RTR_T.
  • Splitting the p.d. between parallel branches. Each branch has the same p.d.
  • Mixing up ammeters and voltmeters. An ammeter goes in series. A voltmeter goes in parallel.
  • Rounding too early. Keep fractions like 13.0\dfrac{1}{3.0} in your calculator until the end.
  • Expecting the bigger resistor to carry more current in parallel. It carries less.

Key points

  • Series: one path. Same current everywhere. P.d.s add to the supply p.d. RT=R1+R2+…R_T = R_1 + R_2 + \dots
  • Parallel: several paths. Same p.d. across each branch. Branch currents add to the total current.
  • Parallel resistance: 1RT=1R1+1R2+…\dfrac{1}{R_T} = \dfrac{1}{R_1} + \dfrac{1}{R_2} + \dots, always less than the smallest resistor.
  • Adding a parallel branch adds a path, increases the total current and lowers the total resistance.
  • Always check your answers: p.d.s should add up in series, and currents should add up at junctions.