Skip to content

Electricity simulation

Series and Parallel Rules Simulation

Fixed series, parallel and mixed circuits with ammeters and voltmeters at every point. Guided presets prove each rule with live numbers: one current in series, p.d.s that share the supply, currents adding at a junction, and the total resistance.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

A 6 V battery drives a current through a 2 Ω resistor and a 4 Ω resistor in series, and the ammeter reads 1.0 A. A 6 Ω resistor is added to the same loop. What will the ammeter read now?

Try this

  1. 1The simulation opens on the guide Series: one current everywhere. Read the four ammeters, then drag R₂ up to 50 Ω. Do A₁ and A₄ still agree?
  2. 2Open the menu beside the Series, Parallel and Mixed buttons, choose Series: add a resistor and press Add R₃. Compare the Before and Now columns for the total resistance and A₁.
  3. 3Press Parallel and flick the branch switches, either by tapping a switch on the circuit or in the Branch switches panel. Which ammeters change, and which stay the same?
  4. 4From the same menu, choose Exam check: 6 Ω ∥ 3 Ω and work out the total resistance before you read it. Then set both resistors to 6 Ω and predict the new total.
  5. 5Press Mixed and follow the five numbered steps in The rules, checked live. Then drag R₃ up to 100 Ω. Why does the parallel pair now come out close to R₂ on its own?

What the simulation shows

The stage holds three fixed circuits: a series loop, a set of parallel branches, and a mixed circuit with one resistor in series with a parallel pair. Ammeters sit at several points and voltmeters sit across each resistor and across the supply. Every reading updates the moment you change a resistance, a switch or the number of cells.

Glowing dots travel along the wires. Each dot stands for 0.5 C of charge, so faster dots mean a bigger current in that wire. Switch the dots to show electrons and they drift the other way, out of the negative terminal and back into the positive one.

Choose a rule from the Prove a rule menu under the stage. The simulation builds a circuit, outlines the meters to compare and checks the rule with live numbers. The panel under the stage turns green whenever a check updates, so you can change any value and watch the rule keep holding.

Series: one path for the charge

A series circuit has no junctions. Every coulomb goes through every component in turn, which is why each ammeter in the loop gives the same reading. Resistors do not use up current. What a coulomb hands over in a resistor is energy.

The supply gives each coulomb a fixed amount of energy, and the resistors share it between them. So the p.d.s across the resistors always total the supply p.d. The same current flows through each resistor, so the one with the most resistance takes the biggest share. Adding a third resistor raises the total resistance and the current falls.

R=R1+R2+R3R = R_1 + R_2 + R_3

Here RR is the total resistance of the loop.

Parallel: branches side by side

In a parallel circuit, each branch joins the same two points, so every branch has the full supply p.d. The current divides at a junction, and together the branch currents equal the supply current. A branch with less resistance carries more current.

Opening one branch switch stops the current in that branch only. The other branches keep their p.d. and their current, which is why the lamps in a building are wired this way. Closing a switch adds another path: the supply current rises, so the total resistance has fallen. It always ends up smaller than the smallest resistor.

1R=1R1+1R2+1R3\frac{1}{R} = \frac{1}{R_1} + \frac{1}{R_2} + \frac{1}{R_3}

Not every course asks you to calculate this. Pick your course with the symbol switcher and each rule in the simulation shows how your course treats it.

Mixed circuits

The mixed circuit puts one resistor in series with two resistors in parallel. To solve it, replace the parallel pair with a single resistor that has the same effect, then add the series resistor to get the total. Find the supply current from I=V÷RI = V \div R, share out the supply p.d., and split the current at the junction. The rule panel works through those five steps with your own values.

Equations

Check your understanding

8 questions

  1. 1.Three resistors are in series with a battery. An ammeter before the first resistor reads 0.3 A. What does an ammeter after the last resistor read?
  2. 2.A 2 Ω resistor and a 10 Ω resistor are in series with a 6 V battery. What is the p.d. across the 10 Ω resistor?
  3. 3.Two branches of a parallel circuit carry 0.4 A and 1.2 A. What is the current from the supply?
  4. 4.A 4 Ω resistor and a 12 Ω resistor are connected in parallel. What is their total resistance?
  5. 5.Why does adding a resistor in parallel lower the total resistance of a circuit?
  6. 6.Four 1.5 V cells are joined in series, each positive terminal to the next negative terminal. What is their total e.m.f.?
  7. 7.Why are the lamps in a home lighting circuit connected in parallel rather than in series?
  8. 8.In a series loop, a 6 Ω resistor has 3 V across it. What is the current in a 2 Ω resistor in the same loop?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more