Skip to content

Electricity simulation

Charge, Current, Energy and Power Simulation

A lamp, heater, motor or resistor in one loop with two ammeters. Glowing electrons drift round in one-coulomb bunches, each with an energy bar that empties in the component, while a stopwatch and counters test Q = It, E = QV and P = IV. Then cost everyday appliances in kWh.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

In this loop the electrons flow through one ammeter, then a lamp, then a second ammeter. The first ammeter reads 2 A. What does the second ammeter read?

Try this

  1. 1Press Play and watch the lower ammeter. Every bunch that crosses it is one coulomb: count the bunches for 5 seconds on the stopwatch, divide your count by 5 and compare it with the Current card. (If your device is set to reduce motion, the bunches stay still: watch the Charge passed card rise each second instead.)
  2. 2While the stopwatch is running, press Off. What do the ammeters, the counters and the bunches do while the switch is open? Press On, let the stopwatch stop at 30 s, then check the Charge passed and Energy transferred cards with Q = It and E = QV.
  3. 3Choose 2 A for 30 s at 6 V from the Examples menu. Predict the current and power with a 12 V battery, then drag the battery slider to 12 V and compare with the cards and the Working box.
  4. 4Pick Motor and run the circuit. Compare P = IV with the line for the power heating the coil in the Working box. Where does the rest of the energy go?
  5. 5Press Appliances, choose Kettle and set Time switched on to 0.25 h. Use the comparison list: how many hours could the 10 W LED lamp run on the energy the kettle used?

What is on the stage

A battery, a switch, two ammeters and one component make a single loop. Glowing dots drift away from the battery's negative terminal. Each dot stands for a huge number of free electrons, and every sixth dot marks the middle of a bunch holding exactly one coulomb. A stopwatch, a charge counter and an energy counter sit inside the loop. Swap the lamp for a heater, a motor or a resistor, change the battery's voltage and the resistance, and every number responds.

Counting coulombs

The stopwatch runs only while the switch is closed, so its reading is the time for which charge has been moving. The number of bunches crossing an ammeter each second equals the current in amperes, and the counter climbs by that many coulombs every second:

Q=ItQ = It

Both ammeters always agree. A bunch entering the component leaves it with exactly the same charge, because nothing in a series loop can store or destroy charge. On the charge–time graph the line is straight, and its gradient is the current; try the tangent tool.

A volt is a joule per coulomb

Each bunch carries an amber energy bar. It leaves the battery full, empties while it crosses the component, travels back empty and is refilled inside the battery. With a 6 V battery every coulomb hands over 6 J, so

E=QVE = QV

That is exactly what the p.d. across a component measures. The e.m.f. of the battery describes the same exchange from the other side: the work the battery does on each coulomb it sends round. The model battery has no internal resistance, so its e.m.f. and the p.d. across the component are equal.

Power three ways

Power is energy transferred per second. Joules per coulomb multiplied by coulombs per second gives P=IVP = IV, and for a fixed resistance, substituting V=IRV = IR gives two more forms:

P=IV=I2R=V2RP = IV = I^2R = \frac{V^2}{R}

The Working box checks all three with live values, and the gradient of the energy–time graph gives the same answer. Doubling the voltage across the same resistor makes the power four times bigger, because the current doubles too. A motor is different: in this model, most of its energy goes to its kinetic store, so I2RI^2R with the coil's resistance only finds the small share that heats the coil. Use P=IVP = IV for the total.

From joules to kilowatt-hours

Press Appliances to leave the bench for a home. Pick a kettle, a fan heater, a desk fan, a phone charger or an LED lamp, each with a typical rounded power rating, then set the hours of use and the price of a kilowatt-hour. A time-lapse meter rolls through the energy used:

1 kWh=1000 W×3600 s=3.6×106 J1\ \text{kWh} = 1000\ \text{W} \times 3600\ \text{s} = 3.6 \times 10^6\ \text{J}

The cost is the energy in kWh multiplied by the price of one kWh, so a 2 kW heater left on for 3 hours uses 6 kWh. The comparison bars show how heating water or air dwarfs charging a phone.

Honest about the model

The dots move far faster than real electrons, whose drift is well under a millimetre per second. A lamp still lights almost at once, because the electric field reaches the whole loop at nearly the speed of light and sets every electron moving together. Lamps, heaters and resistors keep fixed resistances here, although a real filament's resistance rises as it warms up. The energy bars picture what voltage means; in reality the energy travels through the fields around the wires.

Symbols in your course

Choose your course under Show symbols for. GCSE (AQA) students see the battery's p.d., since AQA never uses e.m.f., and the kilowatt-hour goes beyond that specification. Cambridge writes work done as WW, so V=W/QV = W/Q, and gives e.m.f. the symbol EE. The Punjab Physics 10 book covers all of these ideas in Chapter 16.

Equations

  • Charge, current and time

    Q=It

    charge flow = current × time

    Open calculator →
  • Electrical power (P = IV)

    P=VI

    power = potential difference × current

    Open calculator →
  • Electrical power (P = I²R)

    P=I2R

    power = (current)² × resistance

    Open calculator →
  • Energy, charge and potential difference

    E=QV

    energy transferred = charge flow × potential difference

    Open calculator →
  • Electromotive force (e.m.f.)

    ε=WQ

    e.m.f. = work done by the source ÷ charge

    Open calculator →
  • Electrical energy (E = IVt)

    E=IVt

    energy transferred = current × potential difference × time

    Open calculator →

Check your understanding

8 questions

  1. 1.What does a current of 3 A in a wire mean?
  2. 2.A lamp sits between two ammeters in a single loop. The first ammeter reads 0.4 A. What does the second read?
  3. 3.A 12 V battery with no internal resistance is connected to a heater. How much energy does each coulomb transfer in the heater?
  4. 4.A steady current of 0.5 A flows for 2 minutes. How much charge passes?
  5. 5.A 12 V car lamp takes a current of 4 A. What is its power?
  6. 6.A 5 Ω resistor carries a current of 3 A. What power does it transfer?
  7. 7.How many joules are there in one kilowatt-hour?
  8. 8.Which statement about the electrons in a working circuit with a metal wire is true?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more