Skip to content

Electrical Power and the Cost of Electricity: P = IV, E = Pt and kWh

Use P = IV, P = I²R, E = Pt and E = QV with confidence, understand why electricity is sold in kilowatt-hours, and work out the cost of running a kettle, a phone charger or an air conditioner.

Published · 7 min read

On this page

Electrical power is the rate at which an appliance transfers energy. A 2000 W heater transfers 2000 joules of energy every second. You can work out the power from the current and the potential difference (p.d.):

P=IVP = IV

Here P is the power in watts (W), I is the current in amps (A) and V is the p.d. in volts (V). Some courses, especially in the US, write P=IΔVP = I\Delta V. It is the same equation.

The energy an appliance transfers depends on its power and on how long it is switched on: E = Pt. Electricity companies measure this energy in kilowatt-hours (kWh), not joules, because a joule is a very small amount of energy. To find the cost, multiply the energy in kWh by the price of one kWh.

This guide explains each equation and where it comes from. It then works through examples with a kettle, a phone charger and some household bills.

What is electrical power?

Power is the energy transferred per second:

P=EtP = \frac{E}{t}

Here E is in joules (J) and t is in seconds (s). One watt is one joule per second. One kilowatt (kW) is 1000 W.

In a circuit, the p.d. tells you how much energy each coulomb of charge transfers. The current tells you how many coulombs flow each second. Multiply them, and you get the energy transferred each second. That is why P = IV.

The power rating on an appliance tells you how fast it transfers energy when it works normally. A label might say "230 V, 2.3 kW". This means that, on a 230 V supply, it transfers 2300 J every second.

Worked example 1: a kettle

A kettle is rated at 2.3 kW and runs on a 230 V supply. Find the current. Then find the energy transferred if it heats water for 3.0 minutes.

Given: P = 2.3 kW = 2300 W, V = 230 V, t = 3.0 min = 180 s

Equation for current: I=PVI = \dfrac{P}{V}

Substitution: I=2300230I = \dfrac{2300}{230}

Answer: I = 10 A

Equation for energy: E=PtE = Pt

Substitution: E=2300×180E = 2300 \times 180

Answer: E = 414 000 J, or about 410 kJ (2 significant figures)

How do you use P = I²R?

Sometimes you know the current and the resistance, but not the p.d. Then you can use a second form. Start with P = IV and replace V with IR, from V = IR:

P=I×IR=I2RP = I \times IR = I^2 R

This form is useful for the energy wasted as heat in wires and cables. The current is squared, so doubling the current makes the heating four times as large.

For example, a cable has a resistance of 0.20 Ω. With a current of 10 A, the power wasted is 102×0.20=2010^2 \times 0.20 = 20 W. With 20 A, it is 202×0.20=8020^2 \times 0.20 = 80 W. This is why electricity is sent across a country at very high voltages. For the same power, a higher voltage means a smaller current. A smaller current wastes much less energy in the cables.

Some courses also use P=V2RP = \dfrac{V^2}{R}. It comes from the same two equations and gives the same answers.

How are energy, charge and p.d. linked?

The p.d. between two points is the energy transferred for each coulomb of charge. One volt means one joule per coulomb. This gives:

E=QVE = QV

Here Q is the charge in coulombs (C). Some books use W for the energy and write W = QV. The charge that flows is the current multiplied by the time, Q = It. Put these together and you get:

E=QV=ItV=PtE = QV = ItV = Pt

So E = QV and E = Pt are two routes to the same answer.

Worked example 2: a phone charger

A phone charger supplies a current of 2.0 A at a p.d. of 5.0 V. The phone charges for 1.5 hours. Find the power, the charge that flows and the energy transferred.

Given: I = 2.0 A, V = 5.0 V, t = 1.5 h = 1.5 × 3600 s = 5400 s

Power: P=IV=2.0×5.0=10 WP = IV = 2.0 \times 5.0 = 10\ \text{W}

Charge: Q=It=2.0×5400=10 800 CQ = It = 2.0 \times 5400 = 10\,800\ \text{C}

Energy: E=QV=10 800×5.0=54 000 JE = QV = 10\,800 \times 5.0 = 54\,000\ \text{J}

Check: E=Pt=10×5400=54 000 JE = Pt = 10 \times 5400 = 54\,000\ \text{J}

Both methods give 54 000 J, or 54 kJ. Always change hours into seconds before you work in joules.

Try changing the current and the p.d. in the charge, current, energy and power simulation. Watch how much energy each coulomb carries, and how the power changes.

Why do electricity bills use kilowatt-hours?

A joule is tiny. A home that uses 300 kWh in a month uses more than a billion joules. Numbers that big are hard to read on a bill.

The kilowatt-hour is a much bigger unit. One kWh is the energy transferred by a 1 kW appliance in 1 hour:

1 kWh=1000 W×3600 s=3 600 000 J=3.6 MJ1\ \text{kWh} = 1000\ \text{W} \times 3600\ \text{s} = 3\,600\,000\ \text{J} = 3.6\ \text{MJ}

To find the energy in kWh, use E = Pt with P in kilowatts and t in hours.

In Pakistan and India, one kWh is often called one unit of electricity. A bill that says "250 units" means 250 kWh.

How do you work out the cost of electricity?

cost=energy in kWh×price per kWh\text{cost} = \text{energy in kWh} \times \text{price per kWh}

Prices are different in every country, and they change often. The prices below are round numbers chosen for practice. They are not real tariffs.

Worked example 3: an air conditioner in Lahore

A 1.5 kW air conditioner runs at full power for 8.0 hours a day for 30 days. One unit (1 kWh) costs 45 rupees. Find the cost.

Given: P = 1.5 kW, t = 8.0 × 30 = 240 h, price = 45 rupees per kWh

Energy: E=Pt=1.5×240=360 kWhE = Pt = 1.5 \times 240 = 360\ \text{kWh}

Cost: 360×45=16 200360 \times 45 = 16\,200

Answer: the cost is 16 200 rupees (PKR 16 200)

You can also find the energy from meter readings. Suppose the meter reads 12 345 kWh at the start of the month and 12 705 kWh at the end. The energy used is 12 705 − 12 345 = 360 kWh.

Worked example 4: three more appliances

A kettle in the UK. The 2.3 kW kettle from Example 1 runs for 3.0 minutes, four times a day, for a year. One kWh costs 25 pence.

  • Time each day = 4 × 3.0 = 12 minutes = 0.20 h
  • Energy in a year = 2.3 × 0.20 × 365 = 167.9 kWh
  • Cost = 167.9 × 25 = 4197.5 pence, or about 42 pounds (GBP 42)

A ceiling fan in Delhi. A 60 W fan runs for 10 hours a day for 30 days. One unit costs 8 rupees.

  • Energy = 0.060 kW × 300 h = 18 kWh
  • Cost = 18 × 8 = 144 rupees (INR 144)

A phone charger in the US. The 10 W charger from Example 2 is used for 2.0 hours a day for a year. One kWh costs 16 cents (0.16 US dollars).

  • Energy = 0.010 kW × 730 h = 7.3 kWh
  • Cost = 7.3 × 0.16 = 1.168, so about 1.17 US dollars (USD 1.17) for the whole year

The phone charger costs very little to run. The air conditioner costs a lot, because it has a high power and it runs for many hours. Both power and time matter.

Compare appliances in the cost of electricity simulation. Change the power, the hours of use and the price, and see which change has the biggest effect on the bill.

Common mistakes

  • Using watts in the cost equation. Change watts to kilowatts first: 60 W = 0.060 kW.
  • Using minutes instead of hours. 12 minutes is 0.20 h, not 12 h or 0.12 h.
  • Mixing up power and energy. Power is a rate, in W. Energy is an amount, in J or kWh.
  • Writing "kW per hour". The unit of energy is the kilowatt-hour.
  • Forgetting to square the current in P=I2RP = I^2R, or squaring R by mistake.
  • Mixing pence and pounds. 4197.5 pence is about 42 pounds, not 4197 pounds.
  • Mixing the two sets of units. Use J with W and s, or kWh with kW and h. Do not mix them.

Key points

  • Power is the rate of energy transfer: P=EtP = \dfrac{E}{t}. It is measured in watts, and 1 W = 1 J/s.
  • Electrical power: P=IVP = IV and P=I2RP = I^2R.
  • Energy transferred: E=PtE = Pt and E=QVE = QV, where Q = It.
  • 1 kWh = 3.6 MJ. Bills use kWh because the joule is too small. In Pakistan and India, 1 kWh is often called a unit.
  • Cost = energy in kWh × price per kWh, with P in kW and t in hours.
  • Wires waste energy as heat at a rate of I2RI^2R, so a smaller current wastes much less energy.