Circular Motion and Centripetal Force: Why Moving in a Circle Is Accelerating
Learn why a steady speed round a circle still means a changing velocity, why a resultant force towards the centre is needed, where that force comes from for cars, balls on strings and satellites, and what happens when it stops. Includes F = mv²/r, which Punjab Class 9 needs.
Published · 8 min read
On this page
An object moving in a circle at a constant speed is accelerating. Its speed stays the same, but its direction changes all the time. Velocity is speed in a given direction, so when the direction changes, the velocity changes too. Any change of velocity is an acceleration.
By Newton's laws, an acceleration needs a resultant force. For motion in a circle, that force points towards the centre of the circle, at right angles to the way the object is moving. It is often called the centripetal force, which means "centre-seeking". It is not a new kind of force. It is the job done by a force you already know, such as friction, tension or gravity.
If that force stops, the object stops turning. It carries on in a straight line, along the direction it was moving at that instant.
How can a steady speed still be an acceleration?
Speed is a scalar, so it has a size but no direction. Velocity is a vector, with a size and a direction. Picture a car going round a roundabout in Nairobi at a steady 10 m/s. The speedometer never moves. But one moment the car heads east, a little later south, then west. Each time the direction changes, the velocity changes.
Acceleration is the rate of change of velocity, not just of speed. So the car accelerates the whole way round, even though it never speeds up or slows down.
Worked example 1: a quarter of the way round
A car goes a quarter of the way round a roundabout of radius 25 m at a steady 10 m/s. It starts heading east and finishes heading south. Find the change in speed and the change in velocity. As a stretch, find the average acceleration.
Change in speed:
Change in velocity: to go from 10 m/s east to 10 m/s south, the car must lose its 10 m/s east and gain 10 m/s south. These two changes are at right angles, so combine them with Pythagoras:
The change points south-west: towards the centre, as seen from halfway round the turn.
Distance travelled: a quarter of the circumference, m
Time taken: s
Average acceleration: m/s²
Answer: the speed does not change at all, yet the velocity changes by 14.1 m/s. The average acceleration over that quarter turn is about 3.6 m/s².
Which force keeps an object moving in a circle?
Newton's first law says that, with no resultant force, a moving object keeps going in a straight line at a constant speed. To bend its path into a circle, something must keep pulling or pushing it towards the centre. Because that force acts at 90° to the motion, it does not speed the object up or slow it down. It only turns it.
Different situations use different forces:
| Situation | Force towards the centre |
|---|---|
| A car on a roundabout | Friction between the tyres and the road |
| A ball whirled on a string | Tension in the string |
| The Moon, or a satellite, round the Earth | The Earth's gravity |
| Wet clothes in a spinning washing machine drum | The push of the drum wall |
| A train on a curved track | The sideways push of the rails on the wheels |
For a satellite, gravity alone does the pulling. The International Space Station moves sideways at about 7.7 km/s, so it falls round the Earth instead of into it. For more detail, read how orbits work.
What happens when the force stops?
The object leaves the circle and moves off in a straight line, along a tangent. That is the direction it was travelling at the moment the force stopped. It does not fly straight outwards, away from the centre.
You can see this in everyday life:
- The hammer throw. An athlete spins round, then lets go. The hammer flies off along the tangent, so the timing of the release decides its direction.
- A spin dryer or washing machine. The drum wall pushes the clothes round, but water can escape through the holes. With nothing pushing it round, the water carries straight on and leaves the clothes.
A car on an icy or oily road shows what happens when the force is too small. If friction cannot supply enough force, the car cannot follow the curve. It slides onto a wider path, towards the outside of the bend.
Is there an outward force?
No. In a car turning sharply left, you feel pressed against the right-hand door, and it is tempting to blame an outward force. Really, your body is trying to carry on in a straight line. The car turns left beneath you, so the door moves into your path and pushes you to the left, towards the centre of the turn. The resultant force on you points inwards.
What changes the size of the force needed?
Three patterns are worth knowing. They apply when the other two quantities are kept the same:
- Faster: a bigger force is needed to keep the same mass on the same circle.
- Tighter circle: at the same speed, a smaller radius needs a bigger force. Turn it round: if the force increases while the speed stays the same, the object moves on a smaller circle.
- More mass: a heavier object needs a bigger force for the same speed and radius.
A loaded lorry needs more friction than a bicycle to take the same bend at the same speed, and any vehicle needs more when it goes faster. That is why signs before sharp bends tell drivers to slow down.
Worked example 2 (extension): a ball on a string
A student in Lahore whirls a 0.20 kg ball on a string 0.80 m long, in a flat circle at 4.0 m/s. Ignore gravity. Find the tension in the string. Then find it again at twice the speed.
Equation:
Substitution:
Answer: N
At 8.0 m/s: N
Doubling the speed makes the force four times as big, because the speed is squared.
Worked example 3 (extension): a car on a wet roundabout
A 1200 kg car goes round a roundabout of radius 25 m at 10 m/s. How much friction does it need? On a wet day, the tyres can supply at most 3000 N. What happens?
Substitution:
Answer: N of friction is needed.
On the wet road: 3000 N is less than 4800 N, so the car cannot follow the circle at 10 m/s. It slides wide, towards the outside of the roundabout. At a lower speed, about 7.9 m/s, 3000 N would be just enough.
How can you see this in a simulation?
Our orbits and gravity simulation opens on the ISS preset with the Velocity and force arrows switched on. Press Play. The gravity arrow always points at the Earth's centre, at right angles to the velocity arrow, and the Speed card stays constant all the way round. Then lower the Launch speed and press Launch. The satellite no longer stays on its circle: with less speed, gravity pulls it in closer to the Earth, and if the speed is low enough it hits the ground. A separate circular motion simulation is planned.
Common mistakes
- Saying there is no acceleration because the speed is constant. The velocity changes because its direction changes.
- Drawing the force outwards. The resultant force points towards the centre.
- Treating centripetal force as an extra force. It is a job done by a real force, such as friction, tension or gravity.
- Saying the object flies straight outwards when released. It moves along a tangent.
- Forgetting to square the speed in the extension equation.
Key points
- Steady circular motion is accelerated motion, because the direction of the velocity keeps changing.
- Keeping an object on a circle needs a resultant force towards the centre, perpendicular to its motion.
- That force can be friction, tension, gravity or a contact push.
- If the force stops, the object moves off in a straight line along a tangent.
- More speed, more mass or a tighter circle all need a bigger force.