What Is Electric Current? Charge, Coulombs, Q = It and How Electrons Really Move
Find out what an electric current is, what a coulomb means, how to use Q = It in worked examples, why conventional current and electrons flow opposite ways, how slowly electrons really drift, and why every ammeter in a single loop reads the same.
Published · 7 min read
On this page
An electric current is electric charge on the move. Its size is the rate at which charge flows: how much charge passes a point in the circuit each second. Current is measured in amperes (A), often called amps. Charge is measured in coulombs (C).
A current of 1 A means that 1 coulomb of charge passes a point every second. So charge, current and time are linked by
In a metal wire, the moving charges are tiny particles called free electrons. They drift through the wire surprisingly slowly, yet a lamp lights the instant you close the switch. This post explains both facts.
What is a coulomb?
Charge is a property of particles such as electrons and protons. Each electron carries a very small negative charge. A coulomb is a large amount of charge: it is the charge of about electrons.
So a current of 1 A means that over six billion billion electrons pass each point every second. Counting them one by one is impossible, which is why we count charge in coulombs instead.
How do you use Q = It?
| Letter | Stands for | Measured in |
|---|---|---|
| the charge that flows | coulombs (C) | |
| the current | amperes (A) | |
| the time it flows for | seconds (s) |
Rearranged, the same equation gives and . Cambridge and the Punjab book write it in the form , which works as a definition: current is charge per unit time.
Before you substitute, put the time in seconds and the current in amps. For example, 250 mA is 0.25 A, and 3 minutes is 180 s.
Worked example 1: starting a car
On a frosty morning in Winnipeg, Canada, the starter motor of a car draws 160 A for 1.5 s. How much charge flows through it?
Given: A, s
Equation:
Substitution:
Answer: C
That is a lot of charge in a short time. A starter motor needs thick cables because its current is so large.
Worked example 2: a torch left on
A torch is left on for 15 minutes, and 450 C flows through its bulb. Find the current.
Given: C, s
Equation:
Substitution:
Answer: A
What actually moves in a metal wire?
Metals contain electrons that are free to wander between atoms. These free electrons dart about at random all the time, but with no overall direction, so there is no current.
Connect a cell, and its potential difference pushes the free electrons. They still jiggle about, but now they also drift slowly along the wire, away from the negative terminal and towards the positive terminal. That drift is the current.
Circuit diagrams show the current the other way round. Conventional current is drawn leaving the + terminal and returning to the − terminal. This rule was agreed long before anyone knew about electrons. Electrons have negative charge, so they move opposite to the conventional current. Both pictures describe the same current, and every circuit rule works with conventional current.
| Conventional current | Electron flow | |
|---|---|---|
| Direction outside the cell | from + to − | from − to + |
| Used for | circuit diagrams and rules | explaining what happens inside metals |
How fast do electrons move along a wire?
Very slowly. In a copper wire with a cross-section of 1 mm², carrying 1 A, the electrons drift at about 0.07 mm per second. At that rate, a single electron would need nearly four hours to move 1 metre.
So why does a lamp light the moment you press the switch? Because the wire is already full of free electrons. Closing the switch sets up an electric field all round the loop almost at once, and this change spreads at a large fraction of the speed of light. Every free electron in the circuit starts drifting at practically the same moment, including the ones already inside the lamp.
Think of a bicycle chain. Push one pedal and every link moves together, although each link only travels a short way. The energy reaches the back wheel at once, but no single link has to make the whole journey.
Is current used up in a circuit?
No. In a single loop, every coulomb that enters a lamp comes out of the other side. Charge cannot pile up or vanish, so the current is the same at every point in a series loop.
What the lamp takes is energy, not charge. Each coulomb gives up some energy in the lamp and picks up more in the cell. That is why an ammeter placed before a lamp gives exactly the same reading as one placed after it.
How do you measure current?
Use an ammeter. It must be connected in series, so that the whole current passes through the meter. To do this, you break the circuit and put the ammeter into the gap.
- An ammeter has a very small resistance, so it hardly changes the current.
- Never connect it in parallel across a component. Its low resistance would let a very large current flow.
- Many ammeters have several ranges, such as 0–100 mA and 0–10 A. Begin on the largest range, then move down to the smallest one that the reading still fits on.
- On an analogue meter, check that the needle starts at zero. On a digital meter, note how many decimal places it shows.
Open the charge, current, energy and power simulation. From the Examples menu, pick the one where 2 A flows for 30 s at 6 V, then press Play. Both ammeters in the loop read 2 A. When the stopwatch stops at 30 s, the Charge passed card reads 60 C, just as predicts. Press Off and the current falls to zero everywhere in the loop at once. To build your own loops and move the ammeter around, use the circuit builder.
Common mistakes
- Saying current is used up by a lamp. The lamp takes energy. An ammeter on either side of it reads the same.
- Forgetting to convert minutes to seconds before using .
- Mixing up the directions. Conventional current goes from + to −. Electrons go from − to +.
- Thinking electrons race round the circuit. They drift at a fraction of a millimetre per second. The signal is what travels fast.
- Connecting an ammeter in parallel. It must go in series.
- Treating a coulomb as one electron. It is the charge of about electrons.
Key points
- Current is how fast charge flows past a point. Its unit is the ampere.
- One ampere is one coulomb passing a point each second, so .
- In metals, the charge is carried by free electrons, which drift from − to +. Conventional current is drawn from + to −.
- Electrons drift very slowly, but the whole circuit responds almost at once.
- Current is not used up. It is the same at every point in a series loop.
- Ammeters go in series and have a very small resistance.