Skip to content

The I–V Characteristics Required Practical: Method, Graphs and Exam Questions

A step-by-step guide to the I–V characteristics practical: building the circuit, taking readings in both directions, keeping the current small, plotting the graphs for a resistor, a filament lamp and a diode, finding resistance at a point, and answering the exam questions this practical leads to.

Published · 8 min read

On this page

In the I–V characteristics practical, you set the potential difference (p.d.) across a component, measure the current through it, and repeat for a range of p.d. values. Then you plot current against p.d. You test three components in turn: a fixed resistor, a diode and a filament lamp.

The circuit is a single loop: a power supply, a variable resistor, an ammeter and the component under test. A voltmeter connects across the component alone. For negative values, you reverse the connections, so the current flows through the component the other way.

Each component gives its own shape. The fixed resistor gives a straight, sloping line that crosses the origin. The lamp gives a curve that becomes less steep as the p.d. rises, because its filament heats up. The diode stays almost switched off below about 0.6 V one way round, and passes hardly any current the other way round.

What is this practical trying to find out?

A component's I–V characteristic is its graph of current against p.d. The practical finds each one by experiment, and the exam then asks you to explain it.

  • Independent variable: the p.d. across the component. You choose it.
  • Dependent variable: the current through the component. You measure it.
  • Control variables: the component itself, and, for the fixed resistor, its temperature.

Which circuit do you need?

PartWhere it goesIts job
Power supply or batteryIn the loopPushes the current round
Variable resistorIn series with the componentChanges the p.d. across the component in small steps
AmmeterIn series with the componentMeasures the current through it
VoltmeterIn parallel, across the component onlyMeasures the p.d. across it
Protective resistor (diode only)In series with the diodeStops the current shooting up once the diode conducts

An adjustable power supply can do the variable resistor's job instead.

How do you carry out the practical?

  1. Build the circuit with the fixed resistor. Check that both meters read zero before you switch on.
  2. Set the variable resistor to give a small p.d. Switch on, read both meters, then switch off.
  3. Raise the p.d. in equal steps, such as 1.0 V, up to the safe maximum for the component. Record every pair of readings.
  4. Reverse the supply's connections and take the same set of readings. Record them as negative. A digital meter shows the minus sign; with an analogue meter, swap its leads and add the sign yourself.
  5. Take each reading three times and find the mean.
  6. Repeat the whole method for the filament lamp, then for the diode with its protective resistor.

For the diode, add extra points in the region from roughly 0.4 V to 0.8 V, where its current changes fastest.

How should you record and plot the results?

Give each column a heading that names the quantity and its unit, such as "p.d. / V" or "mean current / A". Keep the same number of decimal places down a column.

Plot current up the side and p.d. along the bottom, with the origin in the middle of the grid so the negative readings fit. Draw a straight line of best fit for the resistor and smooth curves for the lamp and the diode. Ring any point that sits well away from the pattern, and check it again.

Worked example 1: means and an anomaly

A student in Kuala Lumpur measures the current through a fixed resistor three times at each p.d.

  • At 2.0 V: 0.042 A, 0.043 A and 0.041 A
  • At 4.0 V: 0.084 A, 0.086 A and 0.098 A
  • At 6.0 V: 0.128 A, 0.127 A and 0.129 A

Step 1, spot the anomaly: 0.098 A is far from the other two readings at 4.0 V, so leave it out.

Step 2, find the means: 0.042 A at 2.0 V, (0.084+0.086)÷2=0.085(0.084 + 0.086) \div 2 = 0.085 A at 4.0 V, and 0.128 A at 6.0 V.

Step 3, find the resistance at each p.d.: R=VIR = \dfrac{V}{I} gives 2.00.042=47.6\dfrac{2.0}{0.042} = 47.6 Ω, 4.00.085=47.1\dfrac{4.0}{0.085} = 47.1 Ω and 6.00.128=46.9\dfrac{6.0}{0.128} = 46.9 Ω.

Answer: the resistance stays at about 47 Ω, so this resistor is ohmic.

Why do the three graphs have different shapes?

  • Fixed resistor: at a steady temperature, its resistance stays fixed. Current is directly proportional to p.d., so the line is straight, goes through the origin and continues into the negative quadrant. Exams call this a linear component.
  • Filament lamp: a larger current makes the thin filament hotter. Its metal ions vibrate more, and the electrons collide with them more often, so the resistance rises. Every additional volt now gives a smaller rise in current, so the curve becomes less steep, although it never goes completely flat. Heating does not depend on direction, so the negative half is the positive half turned through 180° about the origin.
  • Diode: forwards, almost no current flows below about 0.6 V for a silicon diode. Above that, the current climbs very steeply. Backwards, its resistance is very high and the current stays close to zero.

The lamp and the diode are non-linear. For more on each shape, see our guide to Ohm's law and I–V graphs.

How do you find a resistance from your results?

Pick the point you want. Read its p.d. and its current. Divide the p.d. by the current. This works for every component, curved graph or not.

Worked example 2: a lamp, and the tangent trap

A 6 V lamp gives these mean readings: 0.10 A at 1.0 V, 0.27 A at 5.0 V and 0.30 A at 6.0 V. Find its resistance at 1.0 V and at 6.0 V.

Equation: R=VIR = \dfrac{V}{I}

Resistance at 1.0 V: R=1.00.10=10R = \dfrac{1.0}{0.10} = 10 Ω

Resistance at 6.0 V: R=6.00.30=20R = \dfrac{6.0}{0.30} = 20 Ω

Answer: the resistance at 6.0 V is twice as large, since the filament runs far hotter there.

Now the trap. Near 6.0 V, the curve rises by only 0.30−0.27=0.030.30 - 0.27 = 0.03 A per volt. One divided by that slope is about 33 Ω. That number is not the lamp's resistance, so never take a resistance from the gradient of a curve.

Worked example 3: choosing the protective resistor

Suppose the diode in your kit is rated for 20 mA at most, and the supply can give 6.0 V. About 0.70 V is across the diode when it conducts. Find the smallest protective resistor you could use.

p.d. across the resistor: the two share the supply's p.d., so 6.0−0.70=5.36.0 - 0.70 = 5.3 V

Equation: R=VIR = \dfrac{V}{I}, with I=20 mA=0.020I = 20\ \text{mA} = 0.020 A

Substitution: R=5.30.020R = \dfrac{5.3}{0.020}

Answer: R=265R = 265 Ω. A 330 Ω resistor is a safer choice. It limits the current to 5.3÷330=0.0165.3 \div 330 = 0.016 A, or 16 mA.

What do exam questions on this practical ask?

  • Why is there a variable resistor? To change the p.d. across the component, and so the current, giving a range of readings.
  • Why switch off between readings? So the resistor does not warm up. Its resistance would rise, and the results would no longer be at constant temperature.
  • How do you get negative readings? Reverse the connections to the supply, so the current passes through the component the opposite way.
  • Why take more diode readings near 0.6 V? The current changes quickly there, so closely spaced points show the shape of the curve.
  • The resistor's line misses the origin. Why? Probably a zero error on a meter, which is a systematic error. Check that each meter reads zero before switching on.
  • Why repeat the readings? To spot anomalies and to reduce the effect of random errors by taking a mean.

Rehearse the circuit in the circuit builder. Choose Empty, then join the battery, a variable resistor, a lamp and an ammeter in one loop, with a voltmeter across the lamp. Choose Select, then lower the variable resistor's resistance in steps, selecting the lamp after each one: its Resistance reading climbs as its p.d. grows. Then load the Diode circuit, select the diode and press Turn round. The ammeter falls to 0.00 A. See also the I–V characteristics simulation.

Common mistakes

  • Putting the voltmeter across the component and the variable resistor together. It goes across the component only.
  • Plotting the reversed readings as positive values. They belong in the negative quadrant.
  • Joining the points dot to dot. Draw one smooth line or curve of best fit.
  • Using the gradient of a curve as the resistance. Divide V by I at the point.
  • Explaining the lamp's rising resistance without mentioning temperature. A bigger current heats the filament, and it is the hotter filament that has the higher resistance.

Key points

  • Change the p.d. with a variable resistor or an adjustable supply. The ammeter goes in series, and the voltmeter goes across the component only.
  • Reverse the connections to collect negative readings.
  • Use small currents and switch off after each reading, so the fixed resistor does not warm up.
  • Resistor: a straight line through the origin. Lamp: a curve that grows less steep as the filament heats. Diode: current one way only, above about 0.6 V.
  • Resistance at any point is V ÷ I, never the gradient of a curve.