Skip to content

Ohm's Law and I–V Characteristics: Resistor, Filament Lamp and Diode

Understand V = IR and Ohm's law, sketch and explain the I–V graphs for a fixed resistor, a filament lamp and a diode, and find resistance from a graph the right way.

Published · 7 min read

On this page

Resistance tells you how hard it is for a current to flow through a component. It links the potential difference (p.d.) across the component to the current through it:

V=IRV = I R

Here V is the p.d. in volts (V), I is the current in amps (A) and R is the resistance in ohms (Ω).

Ohm's law says that the current through a conductor is directly proportional to the p.d. across it, as long as the temperature stays the same. A fixed resistor obeys Ohm's law, so its I–V graph is a straight line through the origin. A filament lamp does not. Its graph curves, because its resistance rises as it gets hotter. A diode lets current flow in one direction only, and only once the p.d. passes a small threshold.

This guide explains each graph, shows you how to read resistance from it, and walks you through the practical.

What does resistance mean?

In a metal wire, the current is a flow of electrons. As the electrons move, they collide with the ions in the metal. These collisions oppose the current. A component with a high resistance lets only a small current through for a given p.d.

A resistance of 1 Ω means that a p.d. of 1 V drives a current of 1 A through the component. The rearranged forms of the equation are:

I=VRR=VII = \frac{V}{R} \qquad R = \frac{V}{I}

Worked example 1: a fixed resistor

A p.d. of 12 V across a resistor gives a current of 0.40 A. Find the resistance. Then find the current when the p.d. is raised to 18 V, if the temperature does not change.

Given: V = 12 V, I = 0.40 A

Equation: R=VIR = \dfrac{V}{I}

Substitution: R=120.40R = \dfrac{12}{0.40}

Answer: R = 30 Ω

New current: I=VR=1830=0.60 AI = \dfrac{V}{R} = \dfrac{18}{30} = 0.60\ \text{A}

The p.d. went up by 1.5 times, and so did the current. That is what "directly proportional" means.

What is an I–V characteristic?

An I–V characteristic is a graph of current against p.d. for one component. Most GCSE courses put current on the y-axis and p.d. on the x-axis. Positive values mean the component is connected one way round. Negative values mean the connections have been reversed.

What do the graphs look like for a resistor, a lamp and a diode?

Fixed resistor

The graph is a straight line through the origin. It continues in a straight line into the negative quadrant. The resistance is constant, so the resistor is ohmic. This is only true at a constant temperature. A large current heats a resistor, and then its resistance rises a little.

Filament lamp

The graph passes through the origin and curves. It gets flatter as the p.d. increases in either direction, so it looks like a stretched letter S. Each extra volt adds less current than the one before.

Here is why. A bigger current makes the thin metal filament hotter. The metal ions vibrate more, so the electrons collide with them more often. This increases the resistance. The graph has the same shape for negative values, because the filament heats up whichever way the current flows.

Diode

A diode lets current flow in one direction only, called the forward direction. For a silicon diode, almost no current flows until the p.d. reaches about 0.6 V. After that, the current rises very steeply. In the reverse direction, the resistance is very high and the current is almost zero.

Light-emitting diodes (LEDs) behave in the same way, but their threshold is higher and depends on the colour: roughly 1.8 V for red up to about 3 V for blue or white. Diodes are used to protect circuits if a battery is put in the wrong way round. They are also used to change alternating current into direct current.

ComponentShape of the I–V graphResistanceOhmic?
Fixed resistor (constant temperature)Straight line through the originConstantYes
Filament lampS-shaped curve that flattens at higher p.d.Increases as the filament gets hotterNo
DiodeAlmost zero, then rises steeply after about 0.6 V forwards; almost zero in reverseVery high in reverse; falls after the forward thresholdNo

You can sweep the p.d. and watch each graph being drawn in the I–V characteristics simulation. Try reversing the p.d. across the diode and see what happens to the current.

How do you find resistance from an I–V graph?

Choose a point on the graph. Read off the p.d. and the current at that point. Then calculate R = V/I.

For a fixed resistor, every point gives the same answer. You can also use the gradient: with current on the y-axis, the resistance is 1 ÷ gradient.

For a lamp or a diode, do not use the gradient. The gradient of a tangent to the curve does not give the resistance. Always divide the p.d. by the current at the point you want.

Worked example 2: a filament lamp

A student reads two points from the I–V graph of a filament lamp. At 1.0 V, the current is 0.10 A. At 6.0 V, the current is 0.25 A. Find the resistance of the lamp at each p.d.

Given: point 1: V = 1.0 V, I = 0.10 A. Point 2: V = 6.0 V, I = 0.25 A.

Equation: R=VIR = \dfrac{V}{I}

At 1.0 V: R=1.00.10=10 ΩR = \dfrac{1.0}{0.10} = 10\ \Omega

At 6.0 V: R=6.00.25=24 ΩR = \dfrac{6.0}{0.25} = 24\ \Omega

The resistance more than doubles, because the filament is much hotter at 6.0 V.

Worked example 3: a diode in a circuit

A silicon diode is connected the forward way in series with a 220 Ω resistor and a 6.0 V battery. The p.d. across the diode is 0.70 V. Find the current in the circuit.

Given: battery p.d. = 6.0 V, diode p.d. = 0.70 V, R = 220 Ω

p.d. across the resistor: in a series circuit the p.d. is shared, so 6.0 − 0.70 = 5.3 V

Equation: I=VRI = \dfrac{V}{R}

Substitution: I=5.3220I = \dfrac{5.3}{220}

Answer: I = 0.024 A, or 24 mA (2 significant figures)

The same current flows through the diode. If the diode were turned round, almost no current would flow at all.

How do you investigate I–V characteristics in the lab?

Set up this circuit:

  • a power supply or battery
  • a variable resistor in series, to change the current
  • the component you are testing
  • an ammeter in series with the component
  • a voltmeter in parallel across the component

Then follow these steps:

  1. Adjust the variable resistor to give a range of p.d. values, for example from 0 V to 6 V in steps of 1 V.
  2. Record the current and the p.d. for each setting.
  3. Reverse the connections to the component and repeat, to get negative values.
  4. Repeat the readings and find a mean for each p.d.
  5. Plot current on the y-axis against p.d. on the x-axis, and draw a line or smooth curve of best fit.

For the fixed resistor, switch off between readings so that it does not heat up. For the diode, keep a fixed resistor in series to protect it from large currents. Take extra readings between about 0.4 V and 0.8 V, where the current changes quickly.

Try building this circuit in the circuit builder. Check where each meter must go before you switch on.

Common mistakes

  • Using the gradient for a lamp or diode. Use R = V/I at the point instead.
  • Putting the meters in the wrong places. The ammeter goes in series. The voltmeter goes in parallel.
  • Forgetting to convert units. 24 mA is 0.024 A, and 2.2 kΩ is 2200 Ω.
  • Saying the lamp's resistance rises "because the current rises". The real reason is that the filament gets hotter.
  • Drawing the diode curve rising from 0 V. Almost no current flows until about 0.6 V.
  • Ignoring the axes. With current on the y-axis, a steeper line means a lower resistance.

Key points

  • V=IRV = IR, with V in volts, I in amps and R in ohms.
  • Ohm's law: current is directly proportional to p.d. at constant temperature. Components that obey it are ohmic.
  • Fixed resistor: a straight line through the origin, so the resistance is constant.
  • Filament lamp: a curve that flattens, because the resistance increases as the filament gets hotter.
  • Diode: current flows one way only, after a threshold of about 0.6 V for silicon.
  • Find resistance from a graph with R = V/I at a point, not from the gradient of a curve.