Skip to content

GCSE Physics — AQA · Electricity

Current, resistance and potential difference

4.2.1.3

The current through a component is set by the p.d. across it and by its resistance: more resistance means less current for the same p.d. You must recall V = IR and use it to find p.d., current or resistance.

Loading simulation…

Symbols match your course. Open the full circuit builder simulation for more presets and teacher tools.

Where this fits in AQA electricity

Spec point 4.2.1.3 links the three big quantities of circuit physics: current, resistance and potential difference. It is examined on both tiers. It also contains Required practical activity 3, on resistance, which you can be asked about in the written papers.

How resistance controls current

Two things decide how big the current in a component is: the p.d. across it and its resistance. The p.d. pushes charge through. The resistance opposes that flow.

Keep the p.d. the same and swap in a component with more resistance, and the current gets smaller. Swap in one with less resistance, and the current gets bigger. In a metal wire, resistance comes from the moving electrons bumping into the vibrating ions of the metal.

The equation: you must remember this

V=IRV = IR
QuantitySymbolUnit
potential differenceVVvolt, V
currentIIampere (amp), A
resistanceRRohm, Ω

The word version is potential difference = current × resistance. It is not on the equation sheet, so learn it alongside its two rearrangements, I=VRI = \dfrac{V}{R} and R=VIR = \dfrac{V}{I}.

Worked example 1: finding a resistance

A small heating element in a hand warmer has a p.d. of 4.5 V across it. The current through it is 0.30 A. Calculate its resistance.

Given: V=4.5 VV = 4.5\ \text{V}, I=0.30 AI = 0.30\ \text{A}

Equation: V=IRV = IR, so R=VIR = \dfrac{V}{I}

Substitution: R=4.50.30R = \dfrac{4.5}{0.30}

Answer: R=15 ΩR = 15\ \Omega

Worked example 2: watch the prefixes

A 12 V supply is connected across a 2.4 kΩ resistor. Find the current in milliamps.

Given: V=12 VV = 12\ \text{V}, R=2.4 kΩ=2400 ΩR = 2.4\ \text{k}\Omega = 2400\ \Omega

Equation: I=VRI = \dfrac{V}{R}

Substitution: I=122400I = \dfrac{12}{2400}

Answer: I=0.0050 A=5.0 mAI = 0.0050\ \text{A} = 5.0\ \text{mA}

Kilo means multiply by 1000 and milli means divide by 1000. Convert first, then substitute.

Required practical activity 3: resistance

This practical has two parts, and both can turn up in an exam.

Length of a wire. Clamp a thin wire, such as constantan, along a metre ruler. Connect it in series with a cell and an ammeter, and put a voltmeter across the section being tested. Attach one crocodile clip at zero and move the other clip to change the length. For each length, record the current and the p.d., then work out R=VIR = \dfrac{V}{I}. A graph of resistance against length should be a straight line, because resistance is directly proportional to length.

Resistors in series and parallel. Measure the total current and p.d. for single resistors, then for pairs joined in series and in parallel. You should find that series pairs give a larger total resistance and parallel pairs give a smaller one.

Using the simulation

In the simulation above, open the Empty circuit. Build one loop with the battery, a resistor and an ammeter, and put a voltmeter across the resistor. Select the resistor and raise its resistance in steps. The current falls each time while the p.d. stays the same. Now multiply the ammeter reading by the resistance you set, and check that the answer matches the voltmeter reading every time. Finally, swap in a variable resistor and see how it gives you a smooth way to control the current, just as in the practical.

Equations

  • Potential difference, current and resistance

    Learn this

    V=IR

    potential difference = current × resistance

    Open calculator →

Common mistakes

  • Forgetting to convert kΩ to Ω or mA to A before substituting into V = IR.
  • Rearranging wrongly, for example writing R = I ÷ V.
  • Saying a bigger resistance gives a bigger current for the same p.d.
  • In Required practical 3, leaving the current on so long that the wire heats up and its resistance changes.
  • Measuring the p.d. across the whole circuit instead of across the length of wire being tested.
  • Leaving the unit off a resistance answer, or writing V or A instead of Ω.

Exam-style questions

Original questions written in the style of GCSE AQA. Try each one before you reveal the answer.

  1. 1.A resistor has a potential difference of 6.0 V across it. The current through the resistor is 0.25 A.

    1. (a)Write down the equation that links potential difference (V), current (I) and resistance (R).

      1 mark
      Show the answer

      Answer: V = I R

      Marking points

      • V = I R (potential difference = current × resistance)
    2. (b)Calculate the resistance of the resistor.

      2 marks
      Show the answer

      Answer: R = V ÷ I = 6.0 ÷ 0.25 = 24 Ω

      Marking points

      • 6.0 = 0.25 × R or R = 6.0 ÷ 0.25
      • R = 24 Ω
    3. (c)The resistor is replaced by one with a higher resistance. The potential difference stays at 6.0 V. State what happens to the current.

      1 mark
      Show the answer

      Answer: The current decreases.

      Marking points

      • Current decreases (gets smaller).
  2. 2.A student investigates how the resistance of a wire depends on its length. The wire is fixed along a metre ruler and two crocodile clips are used to select the length being tested.

    1. (a)Describe how the student could use an ammeter and a voltmeter to find the resistance of a 50 cm length of wire.

      4 marks
      Show the answer

      Answer: Place the clips 50 cm apart. Connect the ammeter in series with the wire and the supply, and the voltmeter in parallel across the 50 cm section. Switch on and record both readings. Calculate R = V ÷ I.

      Marking points

      • Clips placed 50 cm apart, measured with the ruler.
      • Ammeter in series with the wire.
      • Voltmeter in parallel across the length of wire being tested.
      • Resistance calculated using R = V ÷ I.
    2. (b)For one length, the voltmeter reads 1.8 V and the ammeter reads 0.45 A. Calculate the resistance of this length of wire.

      2 marks
      Show the answer

      Answer: R = 1.8 ÷ 0.45 = 4.0 Ω

      Marking points

      • R = 1.8 ÷ 0.45
      • R = 4.0 Ω
    3. (c)Explain why the student should switch the circuit off between readings.

      2 marks
      Show the answer

      Answer: The current heats the wire. A rise in temperature would increase the resistance, so length would not be the only variable changing.

      Marking points

      • The current causes the wire to heat up.
      • Higher temperature increases resistance, so the test would not be fair (temperature must stay constant).
  3. 3.The heating element of a hair dryer has a resistance of 46 Ω. It is connected to the 230 V mains supply.

    1. (a)Calculate the current in the heating element.

      2 marks
      Show the answer

      Answer: I = V ÷ R = 230 ÷ 46 = 5.0 A

      Marking points

      • I = 230 ÷ 46
      • I = 5.0 A
  4. 4.A fixed resistor of 1.5 kΩ is used in a circuit for a doorbell. The current through it is 4.0 mA.

    1. (a)Calculate the potential difference across the resistor.

      3 marks
      Show the answer

      Answer: I = 0.0040 A, R = 1500 Ω. V = 0.0040 × 1500 = 6.0 V

      Marking points

      • Both converted: 0.0040 A and 1500 Ω
      • V = 0.0040 × 1500
      • V = 6.0 V

Quick check

6 questions

  1. 1.What is the unit of resistance?
  2. 2.The p.d. across a component stays the same, but its resistance increases. What happens to the current?
  3. 3.A 9.0 V battery is connected across a 3.0 Ω resistor. What is the current?
  4. 4.A current of 0.20 A flows through a 50 Ω resistor. What is the p.d. across it?
  5. 5.In the practical on resistance, why should the current through the wire be kept small?
  6. 6.A wire of a fixed thickness and material is made twice as long. What happens to its resistance?