Cambridge IGCSE Physics (0625) · Electric circuits and electrical safety
Circuit diagrams and components
4.3.1
Circuit diagrams use standard symbols for components such as cells, switches, resistors, LDRs, NTC thermistors, fuses and relays. You need to draw and read them and know how each part behaves; diodes and LEDs are Supplement.
A photo of a circuit is hard to follow. A circuit diagram replaces every part with a standard symbol and every wire with a straight line, so an engineer in Lagos and a student in Lahore read it the same way. Cambridge IGCSE asks you to draw these diagrams, read them, and say how each component behaves in the circuit. Most of the list is Core; diodes and LEDs are Supplement.
Rules for a clear diagram (Core)
Use a ruler for straight wires with square corners.
Put a solid dot wherever wires join at a junction.
Leave no gaps in a wire unless you mean an open switch.
Show ammeters in series and voltmeters in parallel with the part they measure.
Common symbols and what the parts do (Core)
Component
How the symbol looks
What it does in a circuit
Cell
Two parallel lines, one long and one short (the short one is often drawn thicker); the long one is the positive terminal
Provides an e.m.f. that drives charge round the circuit
Battery
Two or more cell symbols joined in a row
Gives a bigger e.m.f. than a single cell
Switch
A break in the wire with a short line hinged at one side
Open: no current. Closed: completes the circuit
Fixed resistor
An empty rectangle
Limits the current; its resistance does not change
Variable resistor
A rectangle crossed by a slanting arrow
Its resistance can be adjusted, for example to dim a lamp
Lamp
A circle with a cross inside
Glows when current flows through its filament
Ammeter, voltmeter
A circle containing A, or a circle containing V
Measure current (in series) and p.d. (in parallel)
Motor, generator
A circle containing M, or a square containing G
A motor turns when current flows; a generator produces an e.m.f. when it is turned
Fuse
A small rectangle with a line running along its length
Its thin wire melts and breaks the circuit if the current exceeds its rating
LDR
A resistor rectangle with two arrows pointing towards it
Resistance falls as the light on it gets brighter
Thermistor (NTC)
A resistor rectangle crossed by a diagonal line with a short flat end
Resistance falls as its temperature rises
You also need to recognise and use these parts:
A power supply can provide d.c. or a.c., and its symbol shows which.
A heater is a resistor designed to transfer energy to its surroundings by heating.
A potential divider gives out an adjustable share of the supply p.d. Its symbol is a resistor with an arrow touching its side, a sliding contact.
A magnetising coil, drawn as a row of loops, becomes an electromagnet when current flows.
A transformer, drawn as two coils with a straight line for the iron core between them, changes the size of an alternating p.d.
A relay uses a small current in its coil to work a switch in a second circuit, so a low-current circuit can control a high-current one.
An electric bell rings while current passes through it.
Worked example: an LDR in a circuit (Core)
An LDR is connected in series with an ammeter and a 6.0 V battery. In dim light the LDR has a resistance of 2000 Ω; in bright sunlight its resistance falls to 300 Ω. Find the current in each case. Treat the ammeter, wires and battery as having no resistance.
Equation:I=V/R
Dim light:
I=20006.0=0.0030A=3.0mA
Bright light:
I=3006.0=0.020A=20mA
Answer: brighter light lowers the resistance, so the current rises from 3.0 mA to 20 mA. Many automatic street lamps use this behaviour to switch themselves on at dusk.
Explore the components in the simulation
In the simulation above, choose the LDR divider starting circuit and move the light level slider. The voltmeter across the LDR responds as its resistance changes: dimmer light, larger resistance, bigger share of the p.d. Then load the Diode circuit and turn the diode round: the current stops.
Common mistakes
✕Drawing the cell symbol with the long and short lines swapped. The long line is the positive terminal.
✕Leaving gaps at corners or forgetting the dot at a junction, so the examiner cannot tell which wires are joined.
✕Saying an LDR's resistance increases in bright light. It decreases as the light gets brighter.
✕Saying an NTC thermistor's resistance increases with temperature. For the NTC type in the syllabus it decreases.
✕Confusing a variable resistor (arrow through the rectangle) with an LDR (arrows pointing at the rectangle).
✕(Supplement) Thinking a diode works either way round. It only conducts in the direction the triangle points.
Exam-style questions
Original questions written in the style of Cambridge IGCSE. Try each one before you reveal the answer.
1.A student draws a circuit diagram for a torch. It has two cells, a switch and a lamp, all in series.
(a)Describe the circuit symbol for a cell and state which side is the positive terminal.
2 marks
Show the answerHide the answer
Answer: A long line next to a shorter line, parallel to each other. The long line is the positive terminal.
Marking points
long line and short line (parallel to each other)
long line is positive
(b)The student adds an ammeter to measure the current in the lamp and a voltmeter to measure the p.d. across it. State how each meter is connected.
2 marks
Show the answerHide the answer
Answer: Ammeter: in series with the lamp. Voltmeter: in parallel, across the lamp.
Marking points
ammeter in series
voltmeter in parallel (across the lamp)
2.A light-dependent resistor (LDR) is used in a circuit that switches on a street lamp.
(a)State how the resistance of an LDR changes when the light falling on it becomes brighter.
1 mark
Show the answerHide the answer
Answer: It decreases.
Marking points
resistance decreases
(b)The LDR is connected in series with a 9.0 V battery and an ammeter. In darkness its resistance is 6000 Ω. Calculate the current.
3 marks
Show the answerHide the answer
Answer: I = V ÷ R = 9.0 ÷ 6000 = 0.0015 A (1.5 mA)
Marking points
I = V/R
9.0 ÷ 6000
0.0015 A or 1.5 mA
(c)Suggest what happens to the ammeter reading as the Sun rises.
1 mark
Show the answerHide the answer
Answer: It increases.
Marking points
reading increases (resistance falls)
3.An NTC thermistor is part of a fire alarm circuit. The circuit also contains a relay, a fuse and an electric bell.
(a)State what happens to the resistance of the NTC thermistor as its temperature rises.
1 mark
Show the answerHide the answer
Answer: It decreases.
Marking points
resistance decreases
(b)Describe what the relay does in this circuit.
2 marks
Show the answerHide the answer
Answer: A small current in the relay coil operates a switch, which turns on a separate circuit carrying a larger current to the bell.
Marking points
a (small) current in the coil operates/closes a switch
switching a separate circuit (with a larger current) for the bell
(c)State the purpose of the fuse.
2 marks
Show the answerHide the answer
Answer: It melts and breaks the circuit if the current becomes larger than its rating, protecting the wiring and components.
Marking points
melts / breaks the circuit
when the current exceeds its rating
4.A student connects a light-emitting diode (LED), a resistor and a battery in series. The LED lights up.
(a)(Supplement) The student turns the LED round in the circuit. State and explain what happens.
2 marks
Show the answerHide the answer
Answer: The LED goes out because there is no current. A diode only lets current pass in one direction.
Marking points
LED does not light / no current
a diode conducts in one direction only
(b)(Supplement) Describe the circuit symbol for an LED.
2 marks
Show the answerHide the answer
Answer: A diode symbol (a triangle with a bar across its point) with two arrows pointing away from it.