Skip to content

Cambridge IGCSE Physics (0625) · Electric circuits and electrical safety

Series and parallel circuits

4.3.2

In a series circuit the current is the same everywhere and resistances add; in a parallel circuit the source current is larger than any branch current and the combined resistance is less than either resistor. Extended candidates also use 1/R = 1/R₁ + 1/R₂.

Loading simulation…

Symbols match your course. Open the full circuit builder simulation for more presets and teacher tools.

Two ways to connect components

Components can sit one after another around a single loop, which makes a series circuit, or side by side on separate branches, which makes a parallel circuit. Cambridge expects you to build and use both. The rules for current, e.m.f. and resistance below are Core unless marked Supplement.

Series circuits (Core)

A series circuit offers the charge just one route, so every bit of charge passes through every component in turn. That means the current has the same value everywhere in the loop. An ammeter placed before, between or after the components gives the same reading.

Combined resistance. Resistors in series simply add. The charge has to push through each one in turn:

R=R1+R2+…R = R_1 + R_2 + \ldots

Combined e.m.f. Cells in series, all facing the same way (positive terminal joined to the negative terminal of the next), add their e.m.f.s. Three 1.5 V cells give 4.5 V. If one cell is put in backwards, its e.m.f. is subtracted instead, so three cells with one reversed give only 1.5 V.

One drawback: if any component breaks, the single loop is broken and everything stops working.

Parallel circuits (Core)

In a parallel circuit the current from the source splits at a junction, flows through the separate branches, and rejoins. The current from the source is larger than the current in any one branch.

Joining two resistors in parallel gives a combined resistance smaller than either resistor on its own. Adding a branch opens an extra path for the charge, so more current flows from the same supply.

Lamps in parallel. House lighting circuits are wired in parallel for good reasons:

  • each lamp can be switched on and off without affecting the others
  • if one lamp fails, the rest stay lit
  • every lamp receives the whole supply p.d., so each one glows at its normal brightness

Worked example 1: a series circuit (Core)

Three 1.5 V cells are joined in series, the same way round, to a 4.0 Ω resistor and an 8.0 Ω resistor in series. Find the current.

Combined e.m.f.: 3×1.5=4.53 \times 1.5 = 4.5 V.

Combined resistance: R=4.0+8.0=12R = 4.0 + 8.0 = 12 Ω.

Current:

I=VR=4.512=0.375 AI = \frac{V}{R} = \frac{4.5}{12} = 0.375\ \text{A}

Answer: 0.38 A, the same everywhere in the loop. (Supplement check: the p.d.s are 0.375×4.0=1.50.375 \times 4.0 = 1.5 V and 0.375×8.0=3.00.375 \times 8.0 = 3.0 V, which add to 4.5 V.)

Worked example 2: a parallel circuit (Supplement)

A 6.0 Ω resistor and a 12 Ω resistor are connected in parallel to a 12 V supply. Find the combined resistance and the currents.

Combined resistance:

1R=16.0+112=312\frac{1}{R} = \frac{1}{6.0} + \frac{1}{12} = \frac{3}{12}

so R=12÷3=4.0R = 12 \div 3 = 4.0 Ω, which is less than either resistor.

Currents: each branch has the full 12 V across it. The 6.0 Ω branch carries 12÷6.0=2.012 \div 6.0 = 2.0 A and the 12 Ω branch carries 12÷12=1.012 \div 12 = 1.0 A. The supply current is 12÷4.0=3.012 \div 4.0 = 3.0 A, which equals 2.0+1.02.0 + 1.0, just as the junction rule says.

Compare both in the simulation

In the simulation above, start from the Series circuit. Place the ammeter in a new spot in the loop and confirm the reading does not change. (Supplement) Now connect a voltmeter across each lamp: the two readings add up to the battery's p.d.

Next switch to Parallel. The meter next to the battery reads the total current. Replace a wire in one branch with a second ammeter and compare: the branch carries only part of the total. Remove one lamp with the Erase tool, and notice that the other lamp stays lit at the same brightness.

Equations

  • Resistors in series

    Learn this

    R=R1+R2

    total resistance = R₁ + R₂

    Open calculator →
  • Resistors in parallel

    Learn this · Supplement

    R=R1R2R1+R2

    1 ÷ total resistance = 1 ÷ R₁ + 1 ÷ R₂

    Open calculator →

Common mistakes

  • Saying current is used up as it passes through each component in a series circuit. It is the same at every point.
  • Adding parallel resistances as if they were in series. Two resistors in parallel always give less than the smaller one.
  • (Supplement) Finding 1/R and forgetting to take the reciprocal at the end, so 1/R = 0.25 is given as 0.25 Ω instead of 4.0 Ω.
  • Adding the e.m.f.s of cells that face opposite ways. A reversed cell subtracts its e.m.f.
  • Giving 'they are brighter' as the advantage of parallel lighting without explaining it: each lamp receives the whole supply p.d. and can be switched independently.
  • (Supplement) Splitting the supply p.d. between parallel branches. Every branch has the full supply p.d. across it; it is the current that divides.

Exam-style questions

Original questions written in the style of Cambridge IGCSE. Try each one before you reveal the answer.

  1. 1.A 5.0 Ω resistor and a 15 Ω resistor are connected in series with a battery made of three 2.0 V cells, all facing the same way.

    1. (a)Calculate the combined e.m.f. of the cells.

      1 mark
      Show the answer

      Answer: 3 × 2.0 = 6.0 V

      Marking points

      • 6.0 V
    2. (b)Calculate the combined resistance of the two resistors.

      1 mark
      Show the answer

      Answer: 5.0 + 15 = 20 Ω

      Marking points

      • 20 Ω
    3. (c)Calculate the current in the loop.

      2 marks
      Show the answer

      Answer: I = V ÷ R = 6.0 ÷ 20 = 0.30 A

      Marking points

      • I = V/R or 6.0 ÷ 20
      • 0.30 A
    4. (d)(Supplement) Calculate the p.d. across the 15 Ω resistor, and hence state the p.d. across the 5.0 Ω resistor.

      2 marks
      Show the answer

      Answer: V = IR = 0.30 × 15 = 4.5 V; the 5.0 Ω resistor has 6.0 − 4.5 = 1.5 V across it.

      Marking points

      • 4.5 V across the 15 Ω resistor
      • 1.5 V across the 5.0 Ω resistor
  2. 2.The lamps in a house in Kenya are connected in parallel to the mains supply.

    1. (a)State two advantages of connecting the lamps in parallel rather than in series.

      2 marks
      Show the answer

      Answer: Each lamp can be switched on or off on its own; if one lamp fails the others keep working. (Also: each lamp has the whole supply p.d. across it.)

      Marking points

      • lamps can be switched independently
      • if one lamp fails the others stay on / each lamp has the whole supply p.d.
    2. (b)Compare the current from the supply with the current in one of the lamps.

      1 mark
      Show the answer

      Answer: The current from the supply is larger than the current in any one lamp.

      Marking points

      • supply current is larger than the current in each lamp (branch)
  3. 3.A 4.0 Ω resistor and a 12 Ω resistor are connected in parallel to a 6.0 V supply.

    1. (a)(Supplement) Calculate the combined resistance of the two resistors.

      2 marks
      Show the answer

      Answer: 1/R = 1/4.0 + 1/12 = 4/12, so R = 3.0 Ω

      Marking points

      • 1/R = 1/4.0 + 1/12
      • 3.0 Ω
    2. (b)(Supplement) Calculate the current in each resistor and the current from the supply.

      3 marks
      Show the answer

      Answer: 4.0 Ω: 6.0 ÷ 4.0 = 1.5 A; 12 Ω: 6.0 ÷ 12 = 0.50 A; supply: 1.5 + 0.50 = 2.0 A

      Marking points

      • 1.5 A in the 4.0 Ω resistor
      • 0.50 A in the 12 Ω resistor
      • 2.0 A from the supply
    3. (c)(Supplement) Explain why the current from the supply equals the sum of the currents in the two branches.

      2 marks
      Show the answer

      Answer: Charge is conserved. It cannot build up at a junction, so the charge entering each second equals the charge leaving each second.

      Marking points

      • charge is conserved (not created or destroyed / cannot build up)
      • charge per second into the junction equals charge per second out
  4. 4.A student connects two identical cells in series with a lamp. The lamp does not light, although all the parts work.

    1. (a)Suggest why the lamp does not light if one cell has been connected the wrong way round.

      2 marks
      Show the answer

      Answer: The two e.m.f.s act in opposite directions, so they cancel and the combined e.m.f. is zero.

      Marking points

      • e.m.f.s act in opposite directions
      • combined e.m.f. is zero (so no current)
  5. 5.A resistor is connected across a battery. A second resistor is then connected in parallel with the first one.

    1. (a)State the effect on the combined resistance of connecting a second resistor in parallel with a first resistor.

      1 mark
      Show the answer

      Answer: The combined resistance decreases; it is less than that of either resistor.

      Marking points

      • combined resistance decreases / less than either resistor

Quick check

6 questions

  1. 1.In a series circuit, the current is
  2. 2.A 10 Ω resistor and a 30 Ω resistor are connected in series. What is their combined resistance?
  3. 3.(Supplement) Two 10 Ω resistors are connected in parallel. What is their combined resistance?
  4. 4.Four 1.5 V cells are connected in series, all facing the same way. What is the combined e.m.f.?
  5. 5.(Supplement) In a parallel circuit, one branch carries 0.8 A and the other carries 0.4 A. What is the current from the supply?
  6. 6.Two resistors are connected in parallel. Which statement about their combined resistance is correct?