Skip to content

GCSE Physics — AQA · Electricity

Electrical charge and current

4.2.1.2

Current is the rate at which electrical charge flows round a closed circuit that contains a source of potential difference. You must recall Q = It, with charge in coulombs, current in amps and time in seconds.

Loading simulation…

Symbols match your course. Open the full circuit builder simulation for more presets and teacher tools.

What AQA expects from you

Spec point 4.2.1.2 covers what an electric current actually is and how it links to charge and time. It is on both tiers and in both Combined Science and GCSE Physics. There is one equation here, and you must remember it: it is not printed on the equation sheet.

Why charge flows

Wires are full of charged particles that can move. In a metal, these are electrons. On their own they move about at random, so there is no overall flow in one direction. Two things are needed to make charge move round a circuit:

  1. A closed circuit. There must be a complete loop with no breaks. Opening a switch makes a gap, and the flow stops everywhere at once.
  2. A source of potential difference. A cell, a battery or a power supply provides the push. Without it, a complete loop of wire and lamps carries no current at all.

What current means

Current is moving charge. We measure how big a current is by its rate of flow: the number of coulombs that pass a point in the circuit every second.

A current of 1 ampere means 1 coulomb of charge passes a point each second. So a current of 3 A moves 3 C past a point every second, and in one minute it moves 180 C.

The equation: you must remember this

Q=ItQ = It
QuantitySymbolUnit
charge flowQQcoulomb, C
currentIIampere (amp), A
timettsecond, s

In words: charge flow equals current multiplied by time. Rearranged, I=QtI = \dfrac{Q}{t} and t=QIt = \dfrac{Q}{I}.

One loop, one current

Put an ammeter anywhere in a circuit that has just one loop and it gives the same reading. Charge is not used up as it passes through a lamp or a resistor. What the components take from the charge is energy, not the charge itself. So an ammeter placed before a lamp reads the same as one placed after it.

Worked example 1: charging a phone

A phone charger supplies a steady current of 1.5 A for 40 minutes. How much charge flows into the phone?

Given: I=1.5 AI = 1.5\ \text{A}, t=40×60=2400 st = 40 \times 60 = 2400\ \text{s}

Equation: Q=ItQ = It

Substitution: Q=1.5×2400Q = 1.5 \times 2400

Answer: Q=3600 CQ = 3600\ \text{C}

Worked example 2: finding a current

In a bicycle lamp, 90 C of charge passes through the bulb in 2.5 minutes. Calculate the current.

Given: Q=90 CQ = 90\ \text{C}, t=2.5×60=150 st = 2.5 \times 60 = 150\ \text{s}

Equation: I=QtI = \dfrac{Q}{t}

Substitution: I=90150I = \dfrac{90}{150}

Answer: I=0.60 AI = 0.60\ \text{A}

A quick check helps here: 0.60 C each second for 150 seconds is 90 C, which matches the question.

Where this leads

Charge flow appears again later in the AQA course. In spec point 4.2.4.2 you link it to energy and potential difference, and the same QQ comes straight from this page. Getting confident with Q=ItQ = It now makes those questions much quicker.

Using the simulation

In the simulation above, load the Series circuit. The ammeter sits in the bottom wire of the loop. Note its reading. Choose the Wire tool and tap the ammeter to swap it for a wire. Then choose the Ammeter tool and tap a different wire, such as the one between the two lamps. The reading does not change, which shows the current is the same all round one loop. Now remove one wire: the current falls to zero everywhere, not just near the break. Use the "Show the flow of" buttons to switch the moving dots between conventional current and electrons. Either way, the dots never pile up or vanish at a lamp.

Equations

Common mistakes

  • Leaving time in minutes or hours instead of converting it to seconds before using Q = It.
  • Forgetting to change milliamps into amps (divide by 1000).
  • Saying current is used up by a lamp; in a single loop the current is the same at every point.
  • Defining current as 'the flow of electricity' instead of the rate of flow of electrical charge.
  • Rearranging Q = It wrongly, for example writing I = Q × t.
  • Forgetting that a closed circuit alone is not enough: there must also be a source of potential difference.

Exam-style questions

Original questions written in the style of GCSE AQA. Try each one before you reveal the answer.

  1. 1.An electric toothbrush is recharged with a steady current of 0.20 A for 3.0 hours.

    1. (a)Write down the equation that links charge flow (Q), current (I) and time (t).

      1 mark
      Show the answer

      Answer: Q = I t (charge flow = current × time)

      Marking points

      • Q = I t
    2. (b)Calculate the charge that flows during the recharge. Give your answer to 2 significant figures.

      3 marks
      Show the answer

      Answer: t = 3.0 × 3600 = 10 800 s. Q = 0.20 × 10 800 = 2160 C, which is 2200 C to 2 significant figures.

      Marking points

      • Time converted: 10 800 s
      • Q = 0.20 × 10 800 (= 2160)
      • Q = 2200 C (2 s.f.)
  2. 2.A torch has a single loop containing a battery, a switch and a lamp. In 2.0 minutes, 48 C of charge flows through the lamp.

    1. (a)Calculate the current in the lamp.

      3 marks
      Show the answer

      Answer: t = 120 s. I = Q ÷ t = 48 ÷ 120 = 0.40 A

      Marking points

      • Time converted: 120 s
      • I = 48 ÷ 120
      • I = 0.40 A
    2. (b)An ammeter is moved from one side of the lamp to the other. State the new reading and explain your answer.

      2 marks
      Show the answer

      Answer: 0.40 A. The circuit is a single closed loop, so the current is the same at every point; charge is not used up by the lamp.

      Marking points

      • Reading stays at 0.40 A.
      • Current is the same at all points in a single closed loop (charge is not used up).
  3. 3.A student connects a lamp to two long wires and joins the free ends of the wires together to make a complete loop. There is no cell or battery.

    1. (a)Explain why the lamp does not light.

      2 marks
      Show the answer

      Answer: There is no source of potential difference, so nothing makes the charge flow round the loop and there is no current.

      Marking points

      • No source of potential difference in the circuit.
      • So no charge flows (no current), even though the circuit is closed.
    2. (b)A battery is added and the current becomes 2.5 A. Calculate the time taken for 1500 C of charge to flow through the lamp. Give your answer in minutes.

      3 marks
      Show the answer

      Answer: t = Q ÷ I = 1500 ÷ 2.5 = 600 s = 10 minutes

      Marking points

      • t = 1500 ÷ 2.5
      • t = 600 s
      • t = 10 minutes
  4. 4.A sensor in a weather station draws a current of 250 mA.

    1. (a)Calculate the charge that flows through the sensor in 1.0 minute.

      3 marks
      Show the answer

      Answer: I = 0.25 A and t = 60 s. Q = 0.25 × 60 = 15 C

      Marking points

      • Current converted: 0.25 A
      • Q = 0.25 × 60
      • Q = 15 C

Quick check

6 questions

  1. 1.What is the unit of electrical charge?
  2. 2.Which statement best describes the size of an electric current?
  3. 3.6.0 C of charge flows past a point in 3.0 s. What is the current?
  4. 4.Three ammeters are placed at different points in a single loop with a battery and two lamps. What do they read?
  5. 5.A current of 0.50 A flows for 2.0 minutes. How much charge flows?
  6. 6.What must a circuit have for charge to flow through it?