Skip to content

Cambridge IGCSE Physics (0625) · Electrical quantities

Electric current

4.2.2

Electric current is a flow of charge, carried in metals by free electrons and measured in amperes with an ammeter in series. Extended candidates define current as charge passing a point per unit time, I = Q/t.

Loading simulation…

Symbols match your course. Open the full circuit builder simulation for more presets and teacher tools.

Current means moving charge (Core)

An electric current is a flow of electric charge. When you switch on a torch, charge moves around the loop formed by the battery, the wires and the lamp. The more charge that passes each second, the bigger the current. Current is measured in amperes (A), often shortened to amps. Charge is measured in coulombs (C).

Small currents are often given in milliamperes: 1 mA = 0.001 A, so 250 mA is 0.25 A.

How metals conduct (Core)

In a metal, some electrons are not tied to any single atom. These free electrons wander through the metal all the time. When a cell is connected across a wire, they drift together along it. That drift is the current in the wire. (Supplement: the electrons drift from the negative terminal of the cell, through the circuit, to the positive terminal, which is the opposite way to the conventional current.)

Insulators such as plastic and rubber have almost no free electrons, so charge cannot flow through them. That is why wires are coated in plastic.

Measuring current with an ammeter (Core)

An ammeter measures current. It goes in series, so that all of the current you want to measure passes through it. A good ammeter has a very small resistance, so adding it barely changes the current.

Cambridge expects you to describe both kinds of meter:

  • An analogue ammeter has a needle moving over a scale. Before using it, check that the needle sits on zero. Read it with your eye directly in front of the needle to avoid parallax.
  • A digital ammeter shows a number. Note how many decimal places it displays, because that limits how precise the reading can be.

Many ammeters have different ranges, for example 0–100 mA, 0–1 A and 0–10 A. If you do not know the size of the current, start on the largest range so the meter is not overloaded. Then switch down to the smallest range that still keeps the reading on the scale. A smaller range spreads the reading over more of the dial, so you can read it more precisely.

Direct and alternating current (Core)

Direct current (d.c.) flows in one direction only. Cells, batteries and solar cells supply d.c.

Alternating current (a.c.) keeps reversing its direction, many times each second. Mains electricity is a.c. It goes through 50 complete cycles each second (a frequency of 50 Hz) in Pakistan, India and the UK, and 60 cycles each second (60 Hz) in the USA.

Worked example (Supplement)

A tablet charger delivers 1.8 A for 25 minutes. Calculate the charge that flows into the tablet battery.

Given: I=1.8I = 1.8 A, t=25×60=1500t = 25 \times 60 = 1500 s.

Equation: rearrange I=Q/tI = Q/t to give Q=ItQ = It.

Substitution:

Q=1.8×1500=2700 CQ = 1.8 \times 1500 = 2700\ \text{C}

Answer: 2700 C, or 2.7×1032.7 \times 10^3 C.

Going the other way: if 720 C passes a point in 4.0 minutes, then I=720÷240=3.0I = 720 \div 240 = 3.0 A. Always change minutes into seconds first.

Watch the charge move in the simulation

In the simulation above, build a single loop with a cell, a lamp and an ammeter, then close the gaps with wire. The moving dots show the current. Place the ammeter on the other side of the lamp: its reading does not change, because the same charge flows through every part of a single loop.

Now, under Show, switch between Current (+ to −), which is conventional current, and Electrons. The dots reverse direction, but the ammeter reading stays exactly the same. Both pictures describe one current.

Equations

  • Charge, current and time

    Learn this · Supplement

    Q=It

    charge flow = current × time

    Open calculator →

Common mistakes

  • Connecting the ammeter in parallel with a component instead of in series.
  • Choosing the 0–10 A range for a current of about 0.2 A. The reading is then hard to read precisely; use the smallest range that keeps it on the scale.
  • Saying that current is 'used up' by a lamp. The current is the same on both sides of a lamp in a series loop.
  • Describing d.c. as current that 'changes size'. D.c. flows in one direction only; a.c. keeps reversing direction.
  • (Supplement) Leaving the time in minutes in I = Q/t, giving an answer 60 times too big.
  • (Supplement) Saying electrons flow from positive to negative. That is the direction of conventional current; electrons go from negative to positive.

Exam-style questions

Original questions written in the style of Cambridge IGCSE. Try each one before you reveal the answer.

  1. 1.A student builds a circuit containing a cell, a switch, a lamp and an ammeter.

    1. (a)State how the ammeter must be connected in the circuit.

      1 mark
      Show the answer

      Answer: In series with the lamp.

      Marking points

      • in series
    2. (b)The ammeter has two ranges, 0–1 A and 0–10 A. The current is about 0.3 A. State which range the student should use and explain why.

      2 marks
      Show the answer

      Answer: 0–1 A, because the reading still fits on this scale and it gives a larger deflection, so it can be read more precisely.

      Marking points

      • 0–1 A range
      • reading stays on scale and can be read more precisely (larger deflection / smaller divisions)
    3. (c)Describe how charge flows through the metal wires of the circuit.

      2 marks
      Show the answer

      Answer: Free electrons in the metal move (drift) through the wire, carrying the charge round the circuit.

      Marking points

      • free electrons carry the charge
      • they move/drift through the wire, round the circuit
  2. 2.A torch is powered by two batteries. A kettle in a kitchen in Pakistan is powered by the mains supply.

    1. (a)State which of these uses direct current (d.c.).

      1 mark
      Show the answer

      Answer: The torch.

      Marking points

      • the torch / the batteries
    2. (b)Describe the difference between direct current and alternating current.

      2 marks
      Show the answer

      Answer: Direct current flows in one direction only. Alternating current keeps reversing its direction.

      Marking points

      • d.c. flows in one direction only
      • a.c. repeatedly changes direction
  3. 3.A charge of 1200 C flows through a car headlamp in 5.0 minutes.

    1. (a)(Supplement) Define electric current.

      1 mark
      Show the answer

      Answer: The charge passing a point in a circuit per unit time.

      Marking points

      • charge passing a point per unit time / charge ÷ time
    2. (b)(Supplement) Calculate the current in the headlamp.

      3 marks
      Show the answer

      Answer: t = 5.0 × 60 = 300 s; I = Q ÷ t = 1200 ÷ 300 = 4.0 A

      Marking points

      • time converted to 300 s
      • I = Q/t or 1200 ÷ 300
      • 4.0 A
    3. (c)(Supplement) State the direction of the conventional current and the direction of electron flow in the wires outside the battery.

      2 marks
      Show the answer

      Answer: Conventional current flows from the positive terminal to the negative terminal. Electrons flow from the negative terminal to the positive terminal.

      Marking points

      • conventional current: positive to negative
      • electrons: negative to positive
  4. 4.A phone battery is charged with a steady current of 2.0 A.

    1. (a)(Supplement) Calculate the charge that flows into the battery in 45 minutes.

      3 marks
      Show the answer

      Answer: t = 45 × 60 = 2700 s; Q = It = 2.0 × 2700 = 5400 C

      Marking points

      • t = 2700 s
      • Q = It or 2.0 × 2700
      • 5400 C
    2. (b)Suggest why an ammeter should have a very small resistance.

      1 mark
      Show the answer

      Answer: So that connecting it does not reduce the current it is measuring.

      Marking points

      • so it does not change/reduce the current being measured

Quick check

6 questions

  1. 1.What is the unit of electric current?
  2. 2.Which particles carry the current in a metal wire?
  3. 3.(Supplement) A current of 0.50 A flows for 40 s. How much charge passes a point in the circuit?
  4. 4.How should an ammeter be connected to measure the current in a lamp?
  5. 5.Which of these supplies alternating current?
  6. 6.(Supplement) In the wires connected to a cell, in which direction do the electrons flow?