Skip to content

Cambridge IGCSE Physics (0625) · Electrical quantities

E.m.f. and potential difference

4.2.3

The e.m.f. of a source is the electrical work it does moving unit charge around a complete circuit; the p.d. across a component is the work done by unit charge passing through it. Both are measured in volts with a voltmeter.

Loading simulation…

Symbols match your course. Open the full circuit builder simulation for more presets and teacher tools.

Two quantities, one unit

Electromotive force (e.m.f.) and potential difference (p.d.) are both measured in volts (V), and both are about energy and charge. They describe opposite ends of the same energy story. The definitions and the use of voltmeters are Core. The two equations are Supplement.

Electromotive force (Core)

A cell, battery, generator or power supply is a source. It does work on charge, pushing it all the way round a complete circuit. The e.m.f. of the source is the electrical work it does in moving one unit of charge (one coulomb) right round that circuit.

So a 1.5 V cell does 1.5 J of work on every coulomb it sends round the loop. A 12 V car battery does 12 J on each coulomb. Despite its name, e.m.f. is not a force. It is measured in volts, just like p.d.

Potential difference (Core)

As charge passes through a component, such as a lamp, a heater or a motor, it does work and energy is transferred to the component and then to the surroundings. The p.d. across the component is the work done by one unit of charge as it passes through that component.

One volt means one joule of work for each coulomb: 1 V = 1 J/C. A lamp with a p.d. of 3 V across it receives 3 J from every coulomb that flows through it.

The difference is the direction of the energy transfer:

  • e.m.f.: energy is given to the charge by the source
  • p.d.: energy is given by the charge to a component

In a simple loop with one cell and one lamp, the energy the cell gives each coulomb is the energy that coulomb hands over in the lamp, so the two values match (ignoring tiny losses in the wires and inside the cell).

Measuring p.d. with a voltmeter (Core)

A voltmeter is always connected in parallel, across the component, with one lead on each side. In effect, it compares the energy per coulomb on the two sides of the component. A good voltmeter has a very large resistance, so almost no current flows through it.

Cambridge expects you to know about analogue and digital voltmeters and their ranges:

  • With an analogue voltmeter, check the zero first and look straight at the needle to avoid parallax error.
  • A digital voltmeter gives a number; its last digit sets the resolution.
  • On a meter with ranges such as 0–3 V and 0–15 V, a p.d. of about 2 V is best measured on 0–3 V. The reading then fills more of the scale and is more precise. If the p.d. might exceed 3 V, start on 0–15 V.

Placing a voltmeter directly across the terminals of a source gives a reading for its e.m.f. when little or no current is being drawn.

Worked example (Supplement)

A 12 V car battery sends 50 C of charge round a circuit. Calculate the work done by the battery.

Given: E=12E = 12 V, Q=50Q = 50 C.

Equation: rearrange E=W/QE = W/Q to W=EQW = EQ.

Substitution:

W=12×50=600 JW = 12 \times 50 = 600\ \text{J}

Answer: 600 J.

A second case uses the p.d. equation. A lamp transfers 36 J of energy when 15 C passes through it. Then V=W/Q=36÷15=2.4V = W/Q = 36 \div 15 = 2.4 V.

Measure both in the simulation

In the simulation above, connect a cell to a resistor in a single loop. Add one voltmeter across the cell and a second across the resistor. Select the cell and change its e.m.f.: both readings change together and stay equal. With only one component in the loop, every joule the cell gives a coulomb is handed over in the resistor. Now add a second resistor to the loop and measure across each one. The two p.d.s split the energy from the cell between them.

Equations

  • Electromotive force (e.m.f.)

    Learn this · Supplement

    E=WQ

    e.m.f. = work done by the source ÷ charge

    Open calculator →
  • Energy, charge and potential difference

    Learn this · Supplement

    W=QV

    energy transferred = charge flow × potential difference

    Open calculator →

Common mistakes

  • Connecting the voltmeter in series. It must go in parallel, across the component.
  • Treating e.m.f. as a force because of its name. It is work done per unit charge, measured in volts.
  • Mixing up the two ideas: e.m.f. is energy given to the charge by a source; p.d. is energy given by the charge to a component.
  • Talking about the 'p.d. through' a component. P.d. is always across or between two points.
  • (Supplement) Multiplying when dividing is needed: V = W/Q, so 36 J and 15 C give 2.4 V, not 540 V.
  • (Supplement) Forgetting to find the charge first with Q = It when a question gives a current and a time instead of a charge.

Exam-style questions

Original questions written in the style of Cambridge IGCSE. Try each one before you reveal the answer.

  1. 1.A small electric motor runs from a 9.0 V battery.

    1. (a)State what is meant by the e.m.f. of the battery.

      2 marks
      Show the answer

      Answer: The electrical work done by the battery in moving unit charge (one coulomb) around a complete circuit.

      Marking points

      • (electrical) work done by the source/battery
      • in moving unit charge around a complete circuit
    2. (b)(Supplement) Calculate the work done by the battery when 30 C of charge flows round the circuit.

      2 marks
      Show the answer

      Answer: W = EQ = 9.0 × 30 = 270 J

      Marking points

      • W = EQ or 9.0 × 30
      • 270 J
  2. 2.A student uses a voltmeter to measure the potential difference across a lamp.

    1. (a)State how the voltmeter is connected.

      1 mark
      Show the answer

      Answer: In parallel with the lamp (across its terminals).

      Marking points

      • in parallel / across the lamp
    2. (b)Define potential difference.

      2 marks
      Show the answer

      Answer: The work done by unit charge (one coulomb) as it passes through a component.

      Marking points

      • work done (energy transferred) by unit charge
      • passing through the component
    3. (c)The voltmeter has two ranges, 0–3 V and 0–15 V. The p.d. is expected to be about 2 V. State which range gives the more precise reading.

      1 mark
      Show the answer

      Answer: 0–3 V

      Marking points

      • 0–3 V
  3. 3.A heater is connected to a 230 V mains supply. A charge of 4000 C passes through the heater.

    1. (a)(Supplement) Calculate the energy transferred by the charge in the heater.

      2 marks
      Show the answer

      Answer: W = VQ = 230 × 4000 = 920 000 J (9.2 × 10⁵ J)

      Marking points

      • W = VQ or 230 × 4000
      • 920 000 J / 9.2 × 10⁵ J
    2. (b)(Supplement) The current in the heater is 8.0 A. Calculate the time taken for this charge to pass.

      2 marks
      Show the answer

      Answer: t = Q ÷ I = 4000 ÷ 8.0 = 500 s

      Marking points

      • t = Q/I or 4000 ÷ 8.0
      • 500 s
  4. 4.A torch contains one cell and one lamp. When the torch is switched on, energy is transferred from the cell to the lamp.

    1. (a)Explain the difference between the e.m.f. of the cell and the p.d. across the lamp, in terms of energy.

      2 marks
      Show the answer

      Answer: The e.m.f. is the energy (work) the cell gives to each unit of charge. The p.d. is the energy each unit of charge transfers to the lamp.

      Marking points

      • e.m.f.: work done by the cell on each unit charge (energy given to charge)
      • p.d.: energy transferred by each unit charge in the lamp
    2. (b)State the unit of e.m.f. and express it in joules and coulombs.

      2 marks
      Show the answer

      Answer: The volt (V); 1 V = 1 J/C.

      Marking points

      • volt (V)
      • 1 V = 1 J/C (joule per coulomb)

Quick check

6 questions

  1. 1.Which statement describes the e.m.f. of a cell?
  2. 2.How is a voltmeter connected to measure the p.d. across a resistor?
  3. 3.(Supplement) A lamp transfers 18 J of energy when 6.0 C of charge passes through it. What is the p.d. across the lamp?
  4. 4.One volt is the same as
  5. 5.(Supplement) A 1.5 V cell moves 40 C of charge around a circuit. How much work does the cell do?
  6. 6.Which instrument is used to measure the e.m.f. of a battery?