Where this sits in AQA Physics
Spec point 4.2.1.4, Resistors, has no Higher-only or physics-only label, so it is common to both tiers and to Combined Science. It contains Required practical activity 4, which Combined Science courses may number differently.
The one equation is , from 4.2.1.3. AQA leaves it off the equation sheet, so learn it, along with .
Three shapes to know
An I–V characteristic shows how one component's current depends on the p.d. across it. Current goes on the vertical axis. Readings with the connections swapped are negative, so the axes cross mid-grid.
- Resistor at constant temperature: a straight line through the origin, continuing into the negative quarter. The current is directly proportional to the p.d., so the resistance stays fixed. AQA calls this an ohmic conductor, and its graph is linear.
- Filament lamp: steep near the origin, then less and less steep as the p.d. grows either way. More current makes the filament hotter, and hotter metal has more resistance, so each extra volt adds less current. The curve never goes flat.
- Diode: current passes one way only. Forwards, hardly any flows until roughly 0.6 V for a silicon diode, then it rises steeply. Backwards, its very high resistance lets almost nothing through. AQA quotes no switch-on value.
The lamp and diode graphs are non-linear: their resistance changes with the current.
Resistance from the graph
Pick a point, take its p.d. and current, and divide: . This works for any component.
For a straight line through the origin, the gradient is current ÷ p.d., which is . So , and a steeper line means a smaller resistance. On a curve, a tangent's gradient does not give the resistance.
Worked example 1: a lamp at two points
On a 12 V filament lamp's I–V graph, the current is 0.60 A at 1.5 V and 2.0 A at 12 V. Find the resistance at each point.
Given: V, A; V, A
Equation:
Substitution: and
Answer: and
If the resistance had stayed at 2.5 Ω, 12 V would push 4.8 A through it. Only 2.0 A flows, because the hotter filament resists more.
Worked example 2: resistance from a gradient
A resistor's I–V line runs from the origin through 5.0 V, 0.20 A.
Gradient: change in current ÷ change in p.d. A/V
Equation and substitution:
Answer: , matching .
Required practical activity 4
- Wire a d.c. supply, switch, variable resistor and ammeter in one loop with the component. The voltmeter goes across the component alone.
- Use the variable resistor, or a variable supply, to set at least five p.d.s, recording both meters each time.
- Swap the component's leads over and repeat, recording negative values.
- Repeat readings, find means, plot current against p.d. and add a best-fit line or curve.
Keep the resistor's current low and switch off after each reading, so its temperature stays steady. Protect the diode with a resistor in series and take extra readings near 0.6 V. Let the lamp heat up, within its rating.
Thermistors and LDRs
4.2.1.4 also covers two sensors: a thermistor's resistance falls as it warms, and an LDR's falls in brighter light. Their uses, such as thermostats and dusk-activated lights, are on the LDRs and thermistors page; this simulation has neither.
On the virtual bench
In the simulation above, the filament lamp starts at 6.0 V, taking 0.354 A, so the Resistance card shows 16.9 Ω. Press Record, drag Power pack output to 12.0 V and record: 0.500 A and 24.0 Ω. Record at 2.0 V as well: 0.219 A and 9.13 Ω. Press Reverse and record again: −0.219 A, the same size but reversed.
Now choose Resistor, then 47 Ω, and press Take a full set of readings. Under the graph, 1 ÷ gradient gives 47.0 Ω. Last, choose Diode and take a full set. Every reversed reading is 0.00 mA, and the run ends reversed, so the Resistance card says "too large to measure".