Skip to content

Motion simulation

Adding and Resolving Vectors Simulation

Glossy vector arrows on graph paper. Slide them head-to-tail to find the resultant, check a scale drawing with a protractor and ruler, split one vector into dashed x- and y-components, and add parallel forces on a bar.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

Someone walks 4 km east, then 3 km north. How far are they from their starting point, measured in a straight line?

Try this

  1. 1Press Reset to start from Two forces at right angles, then press Head-to-tail. Watch F₂ slide across to the tip of F₁. Now press Swap: the order changes, but does the red resultant move at all?
  2. 2Choose Two equal forces 60° apart and turn on Scale drawing (grid, protractor and ruler). Read the length in squares off the ruler and multiply it by the scale. Read the angle off the protractor. Compare both with the Resultant and Direction cards.
  3. 3Pick A walk: 4 km east, then 3 km north. The walker covers 7 km along the path. How far from the start do they end up, and in which compass direction?
  4. 4Switch the Mode to Resolve and choose 8 N at 120° into components. If the dashed components are not showing, press Components. Which component comes out negative, and why? Drag the tip slowly round all four quadrants and watch the signs change.
  5. 5In Parallel forces, choose Equal and opposite: a couple. The resultant is zero, yet the bar turns. Move one force's dot along the bar so that the two forces meet at a single point. What happens to the turning?

Arrows on graph paper

Every vector in this simulation is a coloured arrow drawn to scale on squared paper. Its length shows the size and its angle shows the direction, measured anticlockwise from the +x axis, so 0° points right and 90° points up. The badge in the corner gives the scale, such as one square for 1 N. Grab the round handle on any tip and drag it, or pick a vector in the panel and set its size and direction with the sliders. The arrows can stand for forces in newtons, displacements in kilometres or velocities in metres per second, and the maths is the same for all three.

Head-to-tail addition

Press Head-to-tail and each arrow slides along until its tail sits on the tip of the one before. The glowing red resultant then grows from the very start of the chain to its final tip. Swap reverses the order: the arrows take a different path, but they finish at the same point, because vector addition does not depend on order. With two vectors drawn from one start, the Parallelogram view completes the shape with dashed sides, and its diagonal is the same resultant.

Three cases deserve special attention. Two vectors pointing the same way simply add. Pointing in opposite directions, the smaller is taken from the larger, and the resultant follows the larger one. At 90° to each other they form a right-angled triangle, so R=F12+F22R = \sqrt{F_1^2 + F_2^2}. For any other angle the sim adds up the components instead, as explained below.

Checking a scale drawing

Scale drawing (grid, protractor and ruler) turns the stage into a drawing board. A see-through protractor sits on the start point and a ruler lies along the resultant, marked in squares. Read the length in squares, multiply by the scale, and you have the size. Read the angle where the resultant crosses the protractor and you have the direction. A teacher can hide the resultant in a lesson link, and students then find it from the drawing themselves.

Splitting a vector into components

In Resolve mode a single vector is split into two parts at right angles. Press Components and a dotted line drops from the tip to the x-axis, then dashed arrows mark the two sides of the right-angled triangle, with a small square at the corner:

Fx=Fcos⁡θFy=Fsin⁡θF_x = F\cos\theta \qquad F_y = F\sin\theta

A component can be negative. An 8 N force at 120° leans left, so its x-part is −4.00 N. The table in add mode lists the parts of every vector and adds each column, which is exactly where the head-to-tail chain ends.

Reverse runs the method backwards. You set the two components and the sim builds the vector: F=Fx2+Fy2F = \sqrt{F_x^2 + F_y^2}, and the angle comes from tan⁡−1\tan^{-1} of their sizes. The signs then decide the quadrant, so −3 N and −4 N give 5 N at 233.1°, not 53.1°.

Parallel forces on a bar

The last mode puts two or three upward or downward forces on a wooden bar. Like parallel forces point the same way and add; unlike ones point opposite ways, so the smaller total is taken from the larger, and the resultant follows the larger. A side column stacks the same arrows head-to-tail along one line. Sliding a force along the bar never changes the resultant, but it can change whether the bar turns. Two equal, opposite forces at different points cancel completely as forces, yet they still turn the bar: they form a couple. To explore turning properly, open the principle of moments simulation, and to see forces acting on one object, try the free-body diagram simulation.

Equations

  • Resultant of two perpendicular vectors

    R=F12+F22

    (resultant)² = (first vector)² + (second vector)²

    Open calculator →
  • Horizontal component of a force

    Fx=Fcos θ

    horizontal component = force × cos(angle with the horizontal)

    Open calculator →
  • Vertical component of a force

    Fy=Fsin θ

    vertical component = force × sin(angle with the horizontal)

    Open calculator →

Check your understanding

8 questions

  1. 1.A 5 N force pulls a crate to the right while a 12 N force pulls it upwards. How big is the resultant?
  2. 2.Two vectors are joined head-to-tail. Where does the resultant arrow run?
  3. 3.A 12 N force acts at 30° above the +x axis. Find its x-component.
  4. 4.A vector has an x-component of −5 N and a y-component of +5 N. Which direction does it point, measured anticlockwise from +x?
  5. 5.Forces of 7 N and 3 N act in opposite directions along the same straight line. What is their resultant?
  6. 6.Two forces of the same size pull on a ring, with 120° between their directions. How big is their resultant?
  7. 7.A bar has an upward push at one end and an equal downward pull at the other end. What happens to the bar?
  8. 8.On a scale drawing, 1 cm stands for 2 N. The resultant arrow is 6.5 cm long. What is the resultant force?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more