Skip to content

Electricity simulation

I–V Characteristics Simulation

A practical bench with a power pack, an ammeter in series and a voltmeter across the component. Record readings for a fixed resistor, a filament lamp that glows as it heats and a silicon diode, and watch each point drop onto a live I–V graph with a line or curve of best fit.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

The filament lamp is tested at 2 V, 4 V, 6 V, 8 V, 10 V and 12 V, and R = V ÷ I is worked out at each p.d. What happens to the lamp's resistance as the p.d. goes up?

Try this

  1. 1The lamp starts at 6.0 V. Press Record, then turn the knob on the power pack (or drag the Power pack output slider) to 2 V, 4 V, 8 V, 10 V and 12 V, pressing Record each time. Watch the Resistance card: what happens to V ÷ I as the filament gets hotter?
  2. 2Press Reverse to swap the leads over, then record the same p.d.s again. Compare the half of the graph left of the origin with the half on the right.
  3. 3Choose Resistor and 24 Ω, then press Take a full set of readings. Read the gradient of the line of best fit under the graph and check that 1 ÷ gradient comes back to 24 Ω.
  4. 4Choose Diode and take a full set of readings, then switch the graph to 0 to 0.8 V. At what p.d. does the current start to climb? Tap a point on the steep part and compare V ÷ I with 1 ÷ gradient of the tangent.
  5. 5Choose Lamp and press Clear. Switch on Random variation in readings, then press Record three times without touching the knob. Why do the three currents differ, and how does the mean in the results table help?

The bench

A power pack sits on the left with an output knob, a red display and two sockets. Red and black leads carry its p.d. to a single loop. An ammeter sits in series on the top wire, the component under test stands on the right, and a voltmeter is wired across that component alone. Both meters have a needle with zero in the middle of the dial and a digital display underneath, so a negative reading swings the needle to the left. Violet dots trace conventional current, leaving the + socket and returning to the − socket, and they move faster when more current flows.

Three components can go into the gap: a fixed resistor, a 12 V filament lamp, or a silicon diode with a 470 Ω protective resistor in series. Pressing Reverse swaps the leads at the power pack, so the p.d. across the component, and the current through it, change sign.

Taking a set of readings

Each press of Record copies both meter readings into the results table, and a new point falls onto the graph. Recording again at the same setting adds a repeat to that row, up to three, and the table works out the mean current. With random variation switched on, repeats scatter by up to 1%, as real ones do. The automatic option steps the power pack through both directions for you.

What the graphs show

The fixed resistor gives a straight line through the origin, carrying on into the negative quadrant. Doubling the p.d. doubles the current, so the resistance never changes. The gradient of the line of best fit is 1/R1/R.

The lamp's points rise steeply near the origin and then get less and less steep, making a stretched S that is the same both ways round. As the current grows, the filament heats from room temperature to over 2200 °C, and its resistance climbs from under 2 Ω when cold to 24 Ω at 12 V. You can watch its glow change from dull red to almost white.

The diode lets through almost nothing until the p.d. across it reaches about 0.6 V; then the current shoots up. In reverse it reads 0.00 mA at every setting. The protective resistor takes the rest of the supply p.d., which keeps the current at about 24 mA even with 12 V across the pair.

Resistance at a chosen point

Tap any point to compare two numbers. The chord from the origin gives

R=VIR = \frac{V}{I}

which is how the resistance at a point is defined. The tangent's gradient is shown as well, and for the lamp and the diode its reciprocal is a different, bigger or smaller number. Only for the straight line do the two agree.

Equations

  • Potential difference, current and resistance

    V=IR

    potential difference = current × resistance

    Open calculator →

Check your understanding

8 questions

  1. 1.In a circuit for plotting an I–V graph, how are the two meters connected?
  2. 2.A resistor at constant temperature carries 0.40 A when the p.d. across it is 6.0 V. What is its resistance?
  3. 3.Why does the I–V graph of a filament lamp bend over as the p.d. rises?
  4. 4.What happens to the current through a silicon diode when the p.d. across it is reversed?
  5. 5.On a lamp's I–V graph, the point at 6.0 V and 0.30 A is chosen. What is the lamp's resistance at that point?
  6. 6.Which shape of I–V graph shows a component that obeys Ohm's law?
  7. 7.Why is a resistor connected in series with the diode in this practical?
  8. 8.Why are repeat readings taken at each p.d. and a mean worked out?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more