What AQA asks for (spec 4.5.4)
This whole topic is GCSE Physics only (not Combined Science) and appears on both tiers. You should be able to:
- describe examples of forces making things turn
- recall and use
- use the principle of moments to find a force or distance on a balanced object
- explain how levers and gears pass a turning effect on.
is not on the equation sheet, so you must remember it.
Forces that make things turn
Push a heavy door near its handle and it swings open; push equally hard beside the hinges and it hardly moves. The hinges are the pivot. The size of a force's turning effect about a pivot is its moment.
is the moment in newton-metres (N m) and is the force in newtons (N). is the perpendicular distance in metres from the pivot to the line of action of the force: the line the force acts along, extended if necessary. A larger force, or a force further from the pivot, gives a larger moment.
Worked example 1: a stiff wheel nut. A driver changing a tyre pushes at right angles on a wheel brace with 120 N, 35 cm from the centre of the nut.
Given: N, cm m. Equation: . Substitution: . Answer: N m.
The principle of moments
For a balanced object:
total clockwise moment = total anticlockwise moment
Take both totals about the same pivot, adding every moment on each side.
Worked example 2: a playground see-saw. The plank is uniform and rests on its middle, so its own weight has no moment. A child of weight 320 N sits 1.5 m left of the pivot. How far to the right must a friend of weight 400 N sit for the see-saw to balance?
Given: anticlockwise, 320 N at 1.5 m; clockwise, 400 N at distance . Equation: total clockwise moment = total anticlockwise moment, with for each child. Substitution: , so . Answer: m right of the pivot.
Levers
A lever is a rigid bar that turns about a pivot. To make a small effort lift a large load, the effort is applied far from the pivot and the load sits close to it. The bar passes the effort's moment on to the load. The load's distance is short, so an equal moment means a large force.
A paving slab presses on a builder's bar with 600 N, 0.10 m from the pivot, and the builder pushes 1.5 m from it. The effort needed is only N, but the builder's hand moves 15 times as far as the slab rises. Wheelbarrows and bottle openers work the same way.
Gears
Gears are toothed wheels that lock together. The driving gear's teeth push on the driven gear's teeth, and the two push on each other with equal-sized forces. The moment on each gear is that force multiplied by its own radius.
- A larger driven gear receives a bigger moment but turns more slowly.
- A smaller driven gear receives a smaller moment and spins faster.
- Gears in mesh turn in opposite directions.
A 12-tooth gear driving a 36-tooth gear with same-sized teeth gives the big gear three times the radius, so three times the moment and one turn for every three of the small gear. A bicycle's low gear uses a big rear sprocket this way for climbing hills. (A bicycle's sprockets are linked by a chain, so they turn the same way; two gears whose teeth mesh directly turn opposite ways.)
Using the simulation
In the simulation above, Two weights in balance is loaded first, with the metre rule pivoted at 50 cm and held level on pegs. The readouts show A: 3 N × 0.20 m = 0.600 N m anticlockwise and B: 2 N × 0.30 m = 0.600 N m clockwise. Press Release, below the stage: the rule stays level and the status says Balanced. Drag B to the 85 cm mark and the clockwise total becomes 0.700 N m, so the right end tips down. Level holds the rule again.
Next choose See-saw with two children, predict which end drops and press Release. With g = 9.8 N/kg, child A gives 274.4 N × 1.5 m = 411.6 N m, beating child B's 343 N × 1.0 m = 343.0 N m, so the lighter child goes down. Select B and slide it to 3.2 m along the plank, which is 1.2 m right of the pivot, and the see-saw balances.
Finally, in Find an unknown weight, slide the 3 N weight until the status reads Balanced, find the weight marked ?, then press Reveal to compare.