Turning effect of a force
A force can do more than push a body along. When a body is fixed along one line, like a door on its hinges, a force can turn it instead. This is the turning effect of a force. Learn these terms:
- Rigid body: a body in which the distance between any two of its points does not change when forces act on it.
- Axis of rotation: the fixed line the body turns about. For a door it runs through the hinges.
- Line of action: the line drawn through the point where a force acts, in the direction of the force.
- Moment arm (): the perpendicular distance from the axis of rotation to the line of action of the force.
Torque, or moment of force
The turning effect of a force is measured by its torque, which your textbook also calls the moment of force. Torque is the force multiplied by its moment arm:
With in newtons and in metres, torque comes out in newton metres (N m), its SI unit. Punjab board papers give no formula sheet, so learn this with and .
By the textbook's sign rule, a torque that would turn the body anticlockwise is positive and a clockwise one is negative.
Factors affecting torque
- The size of the force. Double the force at the same place and the torque doubles.
- The moment arm. The same force gives more torque further from the axis. That is why door handles sit on the edge away from the hinges, and why a village hand pump has a long handle.
- The direction of the force. If the line of action passes through the axis, then and the torque is zero, however large the force.
When the force is not at right angles, let be the distance from the axis to the point where the force acts, and the angle between and . The moment arm is , so
The torque is greatest at and zero at . (Careful with the letters: one figure in the textbook names these two distances the other way round. Whatever the labels, the moment arm is always the perpendicular distance from the axis to the line of action of the force.)
Worked numerical 1: a wheel brace
A mechanic in a Gujranwala workshop pushes on a wheel brace with 120 N at right angles to the handle, 0.35 m from the centre of the nut. (a) Find the torque. (b) What force at 0.20 m gives the same torque? (c) Find the torque if the 120 N push at 0.35 m makes an angle of 30° with the handle.
Data: , ,
Couple
Couple: two forces that are equal in size, opposite in direction and parallel, acting at two different points of the same body, so that their lines of action are not the same.
The two forces cancel, so a couple gives no resultant force and cannot move the body from place to place. But both forces turn the body the same way, so their torques add and the body rotates. You apply a couple when you turn a steering wheel with both hands, twist the cap off a water bottle or wind a clock key.
The textbook defines a couple but gives no formula for its torque, so this part goes a little beyond the book. To find the torque of a couple, take a point O between the forces, at distances and from their lines of action. Both torques have the same sense, so
where is the perpendicular distance between the two lines of action.
Worked numerical 2: a steering wheel
A van driver holds a steering wheel of diameter 0.36 m at opposite ends of a diameter. Each hand pushes along the rim with 25 N, in opposite directions. Find the torque of the couple.
Torque in the simulation
In the simulation above, each weight hangs straight down, so its moment arm is its distance from the pivot along the level rule. The simulation calls each torque a moment.
Weight A (3 N at the 30 cm mark) is already selected. Use the A: Position on the scale slider to move it to the 40 cm mark. Its row now reads 3 N × 0.10 m = 0.300 N m, half the torque it had before. At the 50 cm mark the readouts say it acts through the pivot, so it has no moment. Move it back to the 30 cm mark and raise the Weight slider to 6 N. The torque doubles to 1.20 N m.
In the simulation every force on the beam is a weight pulling straight down, so it cannot show a couple. To feel one, twist a bottle cap between finger and thumb.