Skip to content

GCSE Physics — AQA · Forces

Forces and elasticity

4.5.3

Changing an object's shape needs more than one force. Extension is proportional to force up to the limit of proportionality: F = ke (recall it). Work done stretching a spring is stored as elastic potential energy, Ee = ½ke² (on the equation sheet). Required practical 6. Both tiers.

Loading simulation…

Symbols match your course. Open the full hooke's law and springs simulation for more presets and teacher tools.

What AQA asks for: spec point 4.5.3

This topic is on both tiers, in GCSE Physics and in Combined Science. You need to:

  • give examples of forces that stretch, bend or compress an object, and explain why a stationary object needs more than one force to change shape
  • describe the difference between elastic and inelastic deformation
  • recall and use F=keF = ke, which is not on the equation sheet, and calculate a spring constant from linear data
  • tell a linear force–extension relationship from a non-linear one
  • calculate the work done in stretching a spring with Ee=12ke2E_e = \frac{1}{2}ke^2, which is given on the equation sheet
  • describe Required practical 6, force and extension for a spring. Combined Science students do the same practical under a different number.

Changing shape needs two forces

Pull on a loose spring and it just moves the way you pull. To stretch a stationary spring, a second force must act the opposite way: a clamp pulls up on the top while the load pulls down. Two palms squeezing a tennis ball compress it, and a diver pushing down on the free end of a fixed board bends it.

Elastic or inelastic?

An object is elastically deformed if it returns to its original shape and length once the forces are removed. If it stays changed, it has been inelastically deformed. A car's suspension spring deforms elastically over every bump; a paper clip bent open deforms inelastically.

Force and extension

The extension is the increase in length: stretched length minus original length. Up to a point called the limit of proportionality, doubling the force on a spring doubles its extension, so the two are directly proportional:

F=keF = ke

FF is the force in newtons (N), kk the spring constant in newtons per metre (N/m) and ee the extension in metres (m). A stiffer spring has a larger kk. For a compressed spring, ee is the compression.

On a force–extension graph with force on the vertical axis, the linear part is a straight line through the origin with gradient kk. Past the limit of proportionality the line curves: the relationship is non-linear and F=keF = ke no longer applies.

Worked example 1. A spring is 6.0 cm long with nothing on it. A 300 g mass stretches it to 13.0 cm. Take g=9.8g = 9.8 N/kg.

Given: F=mg=0.300×9.8=2.94F = mg = 0.300 \times 9.8 = 2.94 N and e=13.0−6.0=7.0e = 13.0 - 6.0 = 7.0 cm =0.070= 0.070 m. Equation: F=keF = ke, so k=Fek = \dfrac{F}{e}. Substitution: k=2.940.070k = \dfrac{2.94}{0.070}. Answer: k=42k = 42 N/m.

Work done and elastic potential energy

Stretching or compressing a spring means doing work on it, and that energy goes into the spring's elastic potential energy store. As long as the deformation is elastic, all of the work done is stored. Up to the limit of proportionality:

Ee=12ke2E_e = \frac{1}{2}ke^2

Worked example 2. How much energy does the spring in example 1 store?

Given: k=42k = 42 N/m, e=0.070e = 0.070 m. Substitution: Ee=0.5×42×0.0702E_e = 0.5 \times 42 \times 0.070^2. Answer: Ee=0.1029E_e = 0.1029 J, or 0.10 J to 2 s.f. That equals the area under the force–extension line, 12×2.94×0.070\frac{1}{2} \times 2.94 \times 0.070.

Required practical 6

Clamp the spring to a stand with a metre rule upright beside it, its zero level with the top of the spring. Fix a pointer to the bottom of the spring and read the original length. Add slotted masses to a hanger one at a time. Each time, let it settle and read the pointer at eye level to avoid parallax. Find each weight with W=mgW = mg and each extension from the original length. Plot force against extension and use the gradient of the straight section to find kk.

Using the simulation

In the simulation above, the Soft spring starts unloaded, 5.00 cm long. Press Record first to log this original length. Then press Add to hang the 100 g hanger: Load shows 0.980 N and Extension 2.45 cm. Record, add another mass, and repeat. The Force–extension graph points form a straight line with gradient 40 N/m, as on the Spring constant card.

At 500 g the extension is 12.25 cm and Energy stored reads 0.300 J, matching 12×40×0.12252\frac{1}{2} \times 40 \times 0.1225^2. The sixth mass takes the spring past its limit of proportionality. Add a seventh, then press Remove until nothing is left: the spring stays 0.87 cm longer, because it has deformed inelastically. The simulation's messages use two names that the AQA specification does not use: Hooke's law for the straight-line behaviour, and elastic limit for the point where stretching becomes permanent. Swap in a new one resets it. The Rubber band is elastic but its graph is never a straight line.

Equations

  • Hooke's law (spring force)

    Learn this

    F=ke

    force = spring constant × extension

    Open calculator →
  • Elastic potential energy

    On the equation sheet

    Ee=12ke2

    elastic potential energy = 0.5 × spring constant × (extension)²

    Open calculator →

Common mistakes

  • Using the stretched length instead of the extension. Extension = stretched length − original length.
  • Leaving the extension in centimetres. Convert to metres before using F = ke or Ee = ½ke², so k comes out in N/m and the energy in J.
  • Using the mass of the load as the force. Work out its weight first with W = mg, taking g = 9.8 N/kg.
  • Using F = ke or Ee = ½ke² beyond the limit of proportionality. Both only apply while force and extension are directly proportional.
  • Forgetting to square the extension in Ee = ½ke², or leaving out the ½.
  • Assuming that elastic means linear. A rubber band returns to its original length, so it deforms elastically, but its force–extension graph is curved.

Exam-style questions

Original questions written in the style of GCSE AQA. Try each one before you reveal the answer.

  1. 1.A spring hangs from a clamp. Its original length is 4.5 cm. A load of 3.0 N stretches the spring to a length of 10.5 cm. The limit of proportionality is not exceeded.

    1. (a)Write down the equation that links extension, force and spring constant.

      1 mark
      Show the answer

      Answer: force = spring constant × extension (F = k e)

      Marking points

      • force = spring constant × extension
    2. (b)Calculate the spring constant of the spring. Give your answer in N/m.

      3 marks
      Show the answer

      Answer: e = 10.5 − 4.5 = 6.0 cm = 0.060 m. k = F ÷ e = 3.0 ÷ 0.060 = 50 N/m

      Marking points

      • Extension = 6.0 cm = 0.060 m
      • k = 3.0 ÷ 0.060
      • k = 50 N/m
    3. (c)Calculate the elastic potential energy stored in the spring. Use the Physics equation sheet.

      2 marks
      Show the answer

      Answer: Ee = ½ k e² = 0.5 × 50 × 0.060² = 0.090 J

      Marking points

      • Ee = 0.5 × 50 × 0.060² (allow their k)
      • 0.090 J
    4. (d)The load is increased to 4.5 N. The limit of proportionality is still not exceeded. Calculate the new length of the spring.

      3 marks
      Show the answer

      Answer: e = F ÷ k = 4.5 ÷ 50 = 0.090 m = 9.0 cm. Length = 4.5 + 9.0 = 13.5 cm

      Marking points

      • e = 4.5 ÷ 50 (allow their k)
      • e = 0.090 m (9.0 cm)
      • Length = 4.5 + 9.0 = 13.5 cm
  2. 2.A student investigates how the extension of a spring depends on the force acting on it. The student has a clamp stand, a spring, a metre rule, a pointer, a mass hanger and some 100 g slotted masses.

    1. (a)Describe a method the student could use.

      6 marks
      Show the answer

      Answer: Hang the spring from the clamp. Clamp the metre rule vertically beside it and fix the pointer to the bottom of the spring. Read the original length of the spring. Hang the hanger and then add masses one at a time, reading the new length each time with the eye level with the pointer. Extension = new length − original length. Force = weight of the masses, W = m g. Repeat the readings (for example while removing the masses) and find means. Plot a graph of force against extension. (AQA marks 6-mark questions as a whole, by level of response. The marking points below show what a top-level answer covers.)

      Marking points

      • Spring hung from the clamp, with the metre rule held vertically beside it.
      • Original length measured using the pointer (rule zero level with the top of the spring).
      • Masses added one at a time and the length measured after each, with the eye level with the pointer.
      • Extension calculated as new length − original length.
      • Force calculated as the weight of the masses (W = m g); readings repeated and means found.
      • Graph of force against extension plotted.
    2. (b)Give one safety precaution the student should take.

      1 mark
      Show the answer

      Answer: Wear eye protection in case the spring snaps or flies off.

      Marking points

      • Wear eye protection / clamp the stand to the bench so it cannot topple / keep feet away from the masses (soft mat underneath).
    3. (c)Explain how the student could use the graph to tell whether the spring had gone past its limit of proportionality.

      2 marks
      Show the answer

      Answer: Up to the limit of proportionality the points lie on a straight line through the origin. If later points curve away from that line, the limit of proportionality has been exceeded.

      Marking points

      • Up to the limit the graph is a straight line through the origin (extension proportional to force).
      • Points that curve away from (are no longer on) the straight line show the limit has been passed.
  3. 3.A climbing rope is tied to an anchor at the top of a wall. A climber hangs on the rope, which stretches slightly.

    1. (a)Explain why more than one force is needed to stretch the rope.

      2 marks
      Show the answer

      Answer: A single force would just make the rope move (accelerate) in the direction of that force. To stretch it while it stays still, forces must pull at both ends in opposite directions: the anchor pulls up and the climber's weight pulls down.

      Marking points

      • One force on its own would make the rope move / accelerate rather than change shape.
      • Two forces act in opposite directions at the two ends (anchor pulling up, climber's weight pulling down).
    2. (b)Describe how elastic deformation is different from inelastic deformation.

      2 marks
      Show the answer

      Answer: After elastic deformation the object returns to its original shape and length when the forces are removed. After inelastic deformation it does not return to its original shape and length.

      Marking points

      • Elastic: returns to its original shape / length when the forces are removed.
      • Inelastic: does not return to its original shape / length (it stays deformed).
    3. (c)When the climber lets go, the rope returns to its original length. Name the type of deformation the rope has undergone.

      1 mark
      Show the answer

      Answer: Elastic deformation

      Marking points

      • Elastic (deformation)
  4. 4.A student hangs loads on a spring and records the extension each time. Force 0 N: 0 cm. Force 1.0 N: 2.0 cm. Force 2.0 N: 4.0 cm. Force 3.0 N: 6.0 cm. Force 4.0 N: 8.5 cm. Force 5.0 N: 12.0 cm.

    1. (a)Use the results to determine the spring constant of the spring where the relationship is linear.

      2 marks
      Show the answer

      Answer: Using 3.0 N and 0.060 m: k = 3.0 ÷ 0.060 = 50 N/m

      Marking points

      • Any linear-region pair with the extension in metres, for example 3.0 ÷ 0.060
      • k = 50 N/m
    2. (b)Between which two forces was the limit of proportionality exceeded? Give a reason for your answer.

      2 marks
      Show the answer

      Answer: Between 3.0 N and 4.0 N. Up to 3.0 N each newton adds 2.0 cm, so 4.0 N should give 8.0 cm, but the extension is 8.5 cm.

      Marking points

      • Between 3.0 N and 4.0 N
      • At 4.0 N the extension (8.5 cm) is more than the 8.0 cm that proportionality predicts.
    3. (c)Explain why the student should not use Ee = ½ k e² to calculate the energy stored when the force is 5.0 N.

      2 marks
      Show the answer

      Answer: The equation only applies up to the limit of proportionality. At 5.0 N the spring is past that limit, so extension is no longer proportional to force and k is not constant.

      Marking points

      • The equation applies only up to the limit of proportionality.
      • At 5.0 N the limit has been exceeded (extension no longer proportional to force).

Quick check

6 questions

  1. 1.A spring has a spring constant of 200 N/m. What force gives it an extension of 0.030 m?
  2. 2.On a graph of force (vertical axis) against extension (horizontal axis), what does the gradient of the straight section give?
  3. 3.A load of 0.80 N stretches a spring from 12.0 cm to 14.0 cm. What is the spring constant?
  4. 4.Which of these is an example of inelastic deformation?
  5. 5.A spring with a spring constant of 80 N/m is stretched by 0.050 m without passing its limit of proportionality. How much elastic potential energy does it store?
  6. 6.Which of these equations is given on the AQA Physics equation sheet?