Skip to content

Matter and pressure simulation

Hooke's Law Simulation

Load a spring 100 g at a time, read its length through a magnifier and build a force–extension graph point by point. Measure the spring constant from the gradient, the stored energy from the area, and see what happens past the limit of proportionality and the elastic limit.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

A soft spring hangs with 200 g on it, well inside its limit of proportionality. You add another 200 g, so the load doubles. What happens?

Try this

  1. 1With the soft spring and nothing on, press Record. Then press Add, let the bounce die away and press Record again. Keep going until 500 g is on the hanger.
  2. 2Choose the gradient tool on the graph and slide it along your straight line. Compare the gradient with the Spring constant card.
  3. 3Keep adding masses to the soft spring until the label on the bench changes. Which recorded point is the first one off the straight line?
  4. 4Choose Stiff spring, add masses until 1000 g is on, then press Remove until the hanger is gone. Read the magnifier: why is the extension not zero? Press Swap in a new one to start again.
  5. 5Choose Rubber band and record a reading for every 100 g. Could any single gradient describe the whole graph?

What happens on the stage

A steel spring hangs from the arm of a clamp stand, next to a metre rule whose zero lines up with the top of the spring. A red pointer fixed to the bottom of the spring marks its length on the rule, and a magnifier follows the pointer so you can read it to a fraction of a millimetre. Each press of Add hangs another 100 g. The hanger itself counts as the first 100 g. The spring dips, bounces gently and settles.

The load is the weight of everything hanging below the spring, found from W=mgW = mg with the value of g your course uses. Record copies the load, the length and the extension into the results table and adds a point to the graph.

Length is not extension

The commonest slip in this practical is plotting how long the spring is instead of how much it has grown. The dashed line marks where the pointer sat with nothing on, which is the original length. The glowing bracket beside the rule runs from that line down to the pointer, and its size is the extension:

e=L−L0e = L - L_0

Double the load and watch. The bracket doubles, but the pointer reading does not, because every reading still includes the original length. Cambridge, Punjab and several other courses call the extension xx rather than ee. Pick your course in the symbol switcher and the readouts change letter to match.

What the graph tells you

Plot force up the side and extension along the bottom. Cambridge calls this a load–extension graph. While the spring obeys Hooke's law, the points fall on a straight line passing through the origin, and its slope is the spring constant k in newtons per metre. Choose the gradient tool, run it along the line to measure k, then check your value against the Spring constant card. A stiffer spring gives a steeper line.

The area under the line is the work you did to stretch the spring. On the straight section that area is a triangle, so the energy stored is

Ee=12ke2E_e = \tfrac{1}{2} k e^2

Use the area tool from zero to your last point and compare it with the Energy stored card.

Past the limit of proportionality

Keep loading the soft spring. After 500 g the points begin to bend away from the straight line towards the extension axis, because each extra 100 g now pulls it out further than the one before. That bend is the limit of proportionality. Slightly beyond it is the elastic limit. Below that point, lifting the masses off brings the pointer all the way back to the dashed line. Above it the coils open up for good, and with everything removed the pointer stays below the line. The leftover stretch is a permanent extension, and points taken on the way down form a second, lower line on the graph. Swap in a new one to start again with a fresh spring.

Pairs of springs and a rubber band

Hang two stiff springs one below the other and each carries the whole load, so their extensions add and the pair acts like a softer spring with half the spring constant. Hang them side by side and they share the load, which doubles the spring constant. A rubber band is different again. It goes back to its original length, so it is elastic, yet its graph curves from the very first point, so it never obeys Hooke's law.

About the numbers

The spring constants and limits are model values, chosen so that the important changes fall between whole numbers of 100 g masses. Real springs vary, and a real rubber band returns along a slightly lower curve as it is unloaded. The bounce after each change is only there to look natural: every reading uses the settled position.

Equations

  • Hooke's law (spring force)

    F=ke

    force = spring constant × extension

    Open calculator →
  • Elastic potential energy

    Ee=12ke2

    elastic potential energy = 0.5 × spring constant × (extension)²

    Open calculator →

Check your understanding

7 questions

  1. 1.A spring is 6.0 cm long with no load and 9.0 cm long when a 1.5 N load hangs from it. What is its spring constant?
  2. 2.Force is plotted up the side and extension along the bottom. What does the gradient of the straight part tell you?
  3. 3.Which observation shows that a spring has been stretched beyond its elastic limit?
  4. 4.A spring with k = 40 N/m is stretched by 0.10 m, within its limit of proportionality. How much elastic potential energy does it store?
  5. 5.Two identical springs, each with a spring constant of 60 N/m, hang side by side and share a load equally. What is the spring constant of the pair?
  6. 6.A 250 g mass hangs on a spring. Taking g = 9.8 N/kg, what is the load on the spring?
  7. 7.A rubber band goes back to its original length when unloaded, but its force–extension graph is curved. Which statement is correct?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more