Skip to content

Matter and pressure simulation

Pressure in Solids Simulation

Stand a brick on each of its three faces in a tank of sand or foam. Its weight never changes, but the contact area does, so the pressure and the dent change with it. Then compare pairs of everyday objects that press with the same force on very different areas.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

A brick lies flat on dry sand with its largest face, 200 cm², underneath. It is lifted and stood on its end, a face of only 50 cm². What happens to the pressure it puts on the sand?

Try this

  1. 1The brick starts lying flat on dry sand. Before you press End, predict how many times bigger the pressure will be, then compare the two dents it leaves.
  2. 2Press Flat, then Side, and read the cards under the stage each time. The contact area halves from 200 cm² to 100 cm². What happens to the weight, and what happens to the pressure?
  3. 3Press Flat, then change the material from Brick to Steel. The area has not changed, so why does the steel block sink further?
  4. 4Under Resting on, choose Soft foam, then turn the block onto another face. Why does the old dent disappear in foam when it stayed in the sand?
  5. 5Choose Everyday examples and then the pin. Work out both pressures in pascals, converting mm² and cm² to m² first, then check your answers against the readouts.

What this simulation shows

A block measuring 20 cm × 10 cm × 5 cm sits in a glass-fronted tank of dry sand or soft foam. It has three different faces it can rest on: the large one (200 cm²), a long narrow one (100 cm²) and an end (50 cm²). Press a face button and the block lifts out, turns over in the air and lands on the spot kept for that face, so you can see every dent side by side. The glass cuts the sand open along the front of the block, so each dent shows in cross-section.

One weight, three pressures

Whichever way up it lands, the block pushes down on the sand with its whole weight. Turning it over cannot change that number. What does change is how much sand shares the load. Pressure measures exactly this: the force on each square metre of surface.

p=FAp = \frac{F}{A}

Here FF is the force at right angles to the surface in newtons and AA is the contact area in square metres, giving the pressure in pascals. With the end down, the area is a quarter of the flat face, so the pressure is four times bigger and the block sinks further. A warm glow under the contact gets brighter as the pressure rises, and the pressure arrows show the push on each square centimetre.

The force matters too

Change the material and the size stays fixed while the weight changes. A wooden block of 0.50 kg, a brick of 2.0 kg and a steel block of 7.9 kg all have the same faces, so for any one face the pressure rises in step with the weight. Notice that the steel block lying flat and the brick on its end give almost matching pressures.

Getting the units right

Most mistakes in pressure questions come from areas.

AreaIn m²Why
1 cm²0.0001 m²1 m² is 100 cm × 100 cm = 10 000 cm²
1 mm²0.000001 m²1 m² is 1000 mm × 1000 mm = 1 000 000 mm²
200 cm²0.0200 m²200 ÷ 10 000

Weight must be in newtons, so a mass in kilograms is multiplied by gg before you divide by the area.

Everyday examples

The second part of the simulation sets a small and a large contact area next to each other under the same force: the sharp edge and the back of a knife blade, the point and the head of a pin, a stiletto heel and a flat heel, boots and snowshoes on snow, and a balloon resting on a single nail or on a bed of 400. Wide tractor tyres and broad camel feet work in the same way as snowshoes. A scale under the panels runs in powers of ten, because these pressures differ by up to ten thousand times.

About the model

The forces and areas are typical example values. How far anything sinks or cuts in is a simple model: on the same material, more pressure always means further in, but not in proportion. Four times the pressure does not make a dent four times as deep, and real sand, foam and snow behave in more complicated ways, so compare depths, but do not measure them.

In your course

Cambridge IGCSE defines pressure as force per unit area in its Core content, expects you to recall p=F/Ap = F/A, and asks for everyday examples like these. The Punjab Physics 9 book writes P=F/AP = F/A with units of N m⁻², or pascals. AQA GCSE has no separate topic on solids: p=F/Ap = F/A appears in the physics-only section on pressure in fluids, but the equation and the units are identical. It is one of the equations AQA expects you to recall, so it is not on the equation sheet.

Equations

Check your understanding

8 questions

  1. 1.A crate with a weight of 300 N rests on a base of area 0.15 m². What pressure does it exert on the floor?
  2. 2.What is 350 cm² in square metres?
  3. 3.A block is turned so that it rests on a face with one third of the area it used before. What happens to the pressure on the floor?
  4. 4.Why do tractors that work on soft, wet fields have very wide tyres?
  5. 5.A force of 12 N acts on an area of 4.0 mm². What is the pressure?
  6. 6.Which of these is equal to one pascal?
  7. 7.A student of mass 50 kg stands on one foot, with 0.020 m² of shoe touching the floor. Taking g = 10 N/kg, what pressure does the shoe put on the floor?
  8. 8.In the simulation, the steel block lying flat and the brick standing on its end sink almost equally far. Why?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more