Skip to content

Matter and pressure simulation

Upthrust and Floating Simulation

Hang a block from a newtonmeter and lower it into an overflow can: the reading drops by exactly the weight of the liquid that spills out. Then float cubes in four liquids and load a barge past its Plimsoll marks.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

A steel block hangs from a newtonmeter and has just gone completely under the water in a can. It is lowered another 2 cm, deeper into the water but still well clear of the bottom. What happens to the newtonmeter reading?

Try this

  1. 1Start with the aluminium block in Water and note the newtonmeter reading. Press Lower one step at a time: each step puts another quarter of the block under the surface. How much does the reading fall at each step?
  2. 2Lower the block until it is completely under, then press Lower once more. Compare the upthrust and the reading on the balance before and after that last step.
  3. 3Raise the block out of the liquid, then choose Pine wood (floats) as the Material. Before you press Lower, predict at which step the newtonmeter will read zero, then check.
  4. 4Pick Float, drop the Pine wood cube into Water, then try Sea and Glycerol. Compare the percentage under the surface with the cube's density divided by the liquid's.
  5. 5Pick Barge and press Add crate one at a time until the status changes from Safe to sail to Overloaded: the S mark is now under the water. Then switch to Fresh (river) and watch the barge settle lower.

Three experiments, one principle

Anything sitting in a liquid feels an upward push called upthrust. This simulation lets you measure that push in three different ways, and each time it comes out equal to the weight of the liquid the object moves out of its way. That rule is Archimedes' principle, and it explains why ships float, why some blocks sink and why a cargo barge has lines painted on its side.

Weighing a block as it goes under

In the first experiment a cuboid hangs from a newtonmeter above an overflow can that has been filled until it drips from its spout. Press Lower and the block enters the liquid a quarter at a time. Every bit of block that goes under forces the same volume of liquid out through the spout, and it runs into a beaker standing on a balance.

Watch three numbers together. The newtonmeter reading falls as the block goes in, and the drop is the upthrust. The balance shows the mass of liquid collected, and multiplying it by g gives its weight. Those two always match: U=ρVgU = \rho V g, where VV is the volume under the surface. Change the material and the weight changes, but a brass block and an aluminium block of the same size get exactly the same upthrust.

Turn on the pressure arrows to see where the push comes from. Liquid pressure grows with depth (p=hρgp = h \rho g), so the bottom face is pushed up harder than the top face is pushed down. Multiply the difference by the face's area and you get the upthrust again. Once the block is fully under, sending it deeper raises both pressures equally, so nothing changes.

A pine block shows what floating means. Its reading drops to zero while part of it is still dry, and the thread goes slack. At that point the upthrust has grown to equal its weight, so the liquid holds the block up on its own.

Cubes that float or sink

The second experiment drops a 10 cm cube into a tank. A cube less dense than the liquid bobs and settles with a fraction ρobject÷ρliquid\rho_\text{object} \div \rho_\text{liquid} of itself below the surface. Glycerol is the densest liquid offered, so cubes ride highest in it. A nylon cube shows that the liquid matters as much as the object: it sinks in water yet floats in glycerol. An aluminium cube rests on the bottom, where the base supplies the force the upthrust cannot.

Loading a barge

The last scene is a harbour. The barge is a simple box, so its depth in the water is its total mass divided by the water's density and its deck area. Each crate pushes it deeper. Painted on the hull is a simplified Plimsoll mark with two lines: S for sea water and F, a little higher, for fresh water. Real ships carry more lines than this.

Keep adding crates and eventually the barge needs to displace more water than its whole hull can hold. The water reaches the deck, floods in, and the barge goes to the bottom of the harbour. A load that only just floats at sea can sink the barge in a river, because fresh water gives less upthrust for each cubic metre pushed aside.

Equations

Check your understanding

8 questions

  1. 1.A stone weighs 5.0 N in air. Hanging fully under water from a newtonmeter, it reads 3.2 N. What is the upthrust on it?
  2. 2.An object with a volume of 0.002 m³ is completely under water (density 1000 kg/m³). Taking g = 10 N/kg, what is the upthrust?
  3. 3.Why does a liquid push upwards on an object that is under its surface?
  4. 4.A wooden block with a density of 600 kg/m³ floats in sea water with a density of 1030 kg/m³. What percentage of its volume is below the surface, to the nearest 1%?
  5. 5.When a key is lowered completely into a full overflow can, 40 cm³ of water runs out of the spout. The water has a density of 1000 kg/m³. Taking g = 10 N/kg, what is the upthrust on the key?
  6. 6.A cargo ship sails from the sea into a freshwater river without changing its load. What happens?
  7. 7.On a Plimsoll mark, why is the F line painted higher up the hull than the S line?
  8. 8.A metal block hangs completely under water from a newtonmeter. It is lowered further without touching the bottom. What happens to the reading?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more