Upthrust and Floating Explained: Why Ships Float and Stones Sink
Find out where upthrust comes from, how to work it out from a newtonmeter reading, how two densities decide what fraction of a floating object sits under the surface, and why a loaded ship rides lower in a river than at sea.
Published · 8 min read
On this page
- Why does a liquid push upwards at all?
- What does a newtonmeter show when an object is under water?
- What is Archimedes' principle?
- When does an object float, sink or hover?
- Why does a floating object sit at a particular depth?
- How can a ship made of steel float?
- Why does a ship float lower in fresh water than in the sea?
- What are the load lines painted on a ship?
- Common mistakes
- Key points
Upthrust is the upward force that a liquid or a gas exerts on an object in it. It exists because pressure in a fluid grows with depth. The lower surface of a submerged object is deeper than its upper surface, so it receives a bigger push. The upward push on the base beats the downward push on the top, and the difference is the upthrust.
Whether an object floats depends on two forces: its weight pulls it down and the upthrust pushes it up. If the upthrust can grow to match the weight before the object is completely under the surface, the object floats. If it cannot, the object sinks.
Below, you will measure upthrust with a newtonmeter, predict how deep a floating object sits, and see why a ship rides lower in a river than at sea.
Why does a liquid push upwards at all?
Picture a closed tin can held upright under water. The water presses on every surface at right angles. The pushes on the curved side come from all around, so they cancel. The base is deeper than the lid, so it gets the larger force, leaving a resultant force upwards.
Two useful facts follow:
- Upthrust depends on how much of the object is under the surface. As you lower an object in, its base goes deeper and the upthrust grows. Once it is completely covered, going deeper raises the pressure on the lid and the base equally, so the upthrust stays the same.
- Upthrust does not depend on what the object is made of. Hold a brass block and a plastic block of the same size and shape completely under water, and they get the same upthrust, even though their weights differ.
You can watch pressure rise with depth in the liquid pressure and depth simulation. Air gives upthrust too, but far less, as it is roughly 800 times less dense than water. Even so, it lifts a helium balloon.
What does a newtonmeter show when an object is under water?
Hang a stone from a newtonmeter. In air, the reading is its weight. Lower it into water and the reading falls. Gravity pulls on the stone as hard as before, but the water now holds up part of its weight, so the spring has less to support. The smaller reading is often called the apparent weight.
Worked example 1: a stone on a newtonmeter
A student in Nairobi, Kenya, hangs a stone from a newtonmeter. It reads 4.6 N in air and 2.9 N with the stone completely under water. Find the upthrust, then the stone's volume and density. Take g = 9.8 N/kg and water as 1000 kg/m³.
Given: weight in air = 4.6 N, reading in water = 2.9 N
Equation: upthrust = weight in air − reading in water
Substitution: upthrust = 4.6 − 2.9
Answer: upthrust = 1.7 N
Volume: by Archimedes' principle (next section), 1.7 N is the weight of the water pushed aside. Its mass is 1.7 ÷ 9.8 = 0.173 kg, so its volume is 0.173 ÷ 1000 = m³, about 170 cm³. The stone has this volume too.
Density: mass = 4.6 ÷ 9.8 = 0.469 kg, so kg/m³, about right for granite.
What is Archimedes' principle?
More than 2000 years ago, the Greek thinker Archimedes found a simple rule. An object wholly or partly in a fluid feels an upthrust equal to the weight of the fluid it displaces, meaning the fluid it pushes out of the way.
You can test it with a eureka can (an overflow or displacement can). Fill it until water drips from the spout, lower a hanging object in, then catch and weigh the water that spills out. Its weight matches the drop in the newtonmeter reading.
When does an object float, sink or hover?
Compare the weight with the largest upthrust the object could get, which is the upthrust when it is fully submerged.
| Comparison | Result |
|---|---|
| Weight greater than the largest upthrust | Resultant force downwards: it sinks |
| Weight less than the largest upthrust | It rises and settles partly out of the liquid, where upthrust equals weight: it floats |
| Weight equal to the largest upthrust | No resultant force at any depth: it hovers (neutral buoyancy) |
The largest upthrust is the weight of liquid with the object's own volume, so this is really a density test. Denser than the liquid: it sinks. Less dense: it floats. Equal: neutral buoyancy. A submarine uses this by letting sea water into its ballast tanks or blowing it out, and scuba divers in the Red Sea add or release air in a buoyancy jacket.
Why does a floating object sit at a particular depth?
A floating object sinks in until it has displaced its own weight of liquid. Writing out both weights:
Cancel g and rearrange:
The fraction below the surface is the object's density divided by the liquid's. It only applies to floating objects, where it is less than 1.
Worked example 2: how much of an iceberg is hidden?
Icebergs off Newfoundland, Canada, are ice with a density of about 920 kg/m³, floating in sea water of about 1030 kg/m³. What fraction is below the waterline?
Given: = 920 kg/m³, = 1030 kg/m³
Equation:
Substitution:
Answer: 0.89, so about 89% is hidden and only about a ninth shows.
An ice cube in fresh water sits slightly lower: 920 ÷ 1000 = 0.92, so 92% is under.
How can a ship made of steel float?
Steel is nearly eight times as dense as water, so a solid steel block sinks at once. A hull, though, is a thin steel shell around a huge volume of air. What counts is the average density of the whole ship, its total mass divided by the volume of the hull, and that is well below 1000 kg/m³. Squeeze modelling clay into a ball and it sinks; press the same clay into a wide, thin bowl and it floats.
Why does a ship float lower in fresh water than in the sea?
Sailing into a river does not change the ship's weight. It must still displace the same mass of water. Fresh water is less dense than sea water, so that mass takes up more volume, and the ship sinks deeper to displace it.
Worked example 3: from the Bay of Bengal to Kolkata
A cargo ship with a total mass of 12 000 tonnes sails from the Bay of Bengal up the Hooghly River to Kolkata, India. Take sea water as 1030 kg/m³ and the river as fresh water, 1000 kg/m³. The hull's area at the waterline is about 2500 m². How much deeper does the ship float in the river?
Given: m = 12 000 t = kg, and a floating ship displaces its own mass of water.
Equation: volume displaced,
At sea: m³
In the river: m³
Extra volume: 12 000 − 11 650 = 350 m³, so the extra depth is 350 ÷ 2500 = 0.14 m.
Answer: about 14 cm deeper, assuming the hull's sides are vertical near the waterline.
What are the load lines painted on a ship?
Cargo ships carry a circle with a horizontal line through it, the Plimsoll mark, named after Samuel Plimsoll, a British politician who campaigned in the 1870s against overloaded ships. Beside it is a ladder of short lines, and the waterline must stay below the one for the conditions. S (summer) is for sea water. F (fresh water) sits higher, because the ship floats deeper in a river. A ship loaded to F at a river port rises to about S when it reaches the sea. Other lines cover winter seas (W, lower) and the tropics (T and TF).
In the upthrust and floating simulation, you can lower a block on a newtonmeter into an overflow can, drop cubes into four liquids, and load a barge with 5-tonne crates until its S mark goes under. Switch from sea to river and watch the barge settle lower.
Common mistakes
- Thinking only floating objects feel upthrust. A sinking stone gets upthrust too, just less than its weight.
- Saying an object weighs less in water. Its weight is unchanged. The newtonmeter reads less because the water supports some of it.
- Assuming deeper always means more upthrust. That is only true while more of the object is going under.
- Using the object's density for the displaced liquid. The weight of liquid displaced uses the liquid's density.
- Saying a ship rises when it enters a river. It settles lower, because fresh water is less dense.
Key points
- Upthrust is the upward force from a fluid, caused by the greater pressure on the lower surface of an object.
- Upthrust = weight in air − reading when the object is in the liquid.
- An object floats if the upthrust can equal its weight before it is fully under, and sinks if its weight beats the largest possible upthrust.
- Archimedes' principle: upthrust = weight of fluid displaced.
- For a floating object, the fraction under the surface = .
- Ships float because their average density is less than water's. They sit lower in fresh water, so the F load line is above the S line.