Skip to content

How a Power Station Generates Electricity: Boiler, Turbine, Generator and Grid

Trace each stage of a thermal power station, from the furnace to the step-up transformer, and see how electromagnetic induction makes the electricity. Compare wind, hydro, tidal and solar cells, and work out the efficiency and fuel use of a real-sized station.

Published · 8 min read

On this page

Most power stations work in the same basic way. Energy from a fuel boils water in a boiler, making high-pressure steam. The steam pushes on the blades of a turbine and makes it spin. The turbine turns a generator, where a magnet and coils of wire rotate relative to each other. This induces an alternating potential difference. Finally, a step-up transformer increases the p.d. so the electricity can cross the country on the grid.

Wind, hydroelectric and tidal stations skip the boiler, because moving air or water spins the turbine directly. Solar cells skip the turbine and the generator too.

A thermal power station is typically only about 35–45% efficient, although the best gas stations do better. More than half of the fuel's energy is wasted, mostly as heat in the cooling water.

What are the stages in a thermal power station?

A thermal power station is any station that boils water to make steam: coal, oil, gas, biofuel and nuclear stations all count. (Many modern gas stations also burn the gas in a gas turbine, a bit like a jet engine, and then use the hot exhaust to raise steam for a second turbine. At school level, treating gas like the other fuels is fine.)

StageWhat happensWhere the energy is
1. FurnaceThe fuel burns in airChemical store of the fuel, transferred by heating
2. BoilerWater in pipes boils into steam at high pressure and temperatureThermal store of the steam
3. TurbineSteam rushes past rows of angled blades and spins the shaftKinetic store of the turbine
4. GeneratorThe shaft turns the generator, which induces a p.d.Transferred electrically
5. TransformerThe p.d. is stepped up for the transmission cablesTransferred electrically to the grid

After the turbine, the used steam passes through a condenser, where cold water from a river, the sea or a cooling tower turns it back into water. That water is pumped back to the boiler. The cooling water carries away a large share of the energy, which is why big stations are built beside rivers or coasts, or have tall cooling towers.

A nuclear station has the same boiler, turbine and generator. Instead of a furnace it has a reactor, where uranium nuclei split (fission) and release energy that heats the water.

How does the generator make electricity?

A generator uses electromagnetic induction. When a magnetic field through a coil of wire changes, a potential difference is induced across the coil.

In a small classroom generator, a coil spins between two fixed magnets. Huge power-station generators turn this round. The turbine spins a powerful electromagnet, and heavy coils of copper sit in a ring around it without moving. Either way, the magnet and the coils rotate relative to each other, so the field through the coils keeps changing direction. The output is alternating current.

A bigger p.d. is induced if the generator spins faster, has a stronger magnet, or has more turns in its coils. The rate of turning also sets the frequency, so generators are held at a steady speed: 50 Hz in the UK, India and Pakistan, or 60 Hz in the USA.

There is a catch. The induced current makes its own magnetic field, which opposes the turning. So when demand rises, the turbine needs more steam and the station burns more fuel. The electrical energy has to come from somewhere.

Why is the p.d. stepped up?

The generator's output goes straight to a step-up transformer next to the station. It raises the p.d. to hundreds of thousands of volts. For the same power, a higher p.d. means a smaller current, so the cables waste much less energy as heat. Near towns, step-down transformers lower the p.d. again for homes. For the details, see transformers and the National Grid.

How do wind, hydro and tidal stations differ?

These stations need no fuel and no boiler. Something that is already moving pushes the turbine round.

  • Wind: moving air pushes on the blades. They turn a generator inside the housing at the top of the tower.
  • Hydroelectric: water stored behind a dam has a gravitational potential store. It rushes down large pipes, speeds up and spins turbines at the bottom.
  • Tidal: a barrage traps water at high tide. As the sea level falls, the water flows out through turbines in tunnels.
  • Waves: the rise and fall of the water drives a generator.

Geothermal stations have no furnace or boiler, because the steam comes up from hot rocks underground, but they still use a turbine and a generator.

How are solar cells different?

Solar cells have no moving parts. Light falling on a cell produces a p.d. directly, with no turbine and no generator. The output is direct current, which a device called an inverter changes to a.c. for the grid (beyond your course).

Do not confuse them with solar heating panels, which heat water but generate no electricity.

StationBoiler?Turbine?Generator?
Coal, oil, gas, biofuelYesYesYes
NuclearYes, heated by a reactorYesYes
GeothermalNo, steam comes from the groundYesYes
Wind, hydroelectric, tidalNoYesYes
Solar cellsNoNoNo

How efficient is a power station?

Efficiency is the fraction of the input that ends up as useful output:

efficiency=useful power outputtotal power input\text{efficiency} = \frac{\text{useful power output}}{\text{total power input}}

Typical values, which vary from station to station:

  • Most coal, oil and nuclear stations: about 35–45%, with nuclear stations often near the low end
  • The best modern gas stations, which use their hot exhaust a second time: up to about 60%
  • Large hydroelectric stations: around 90%

Most of the waste in a thermal station is the energy carried off by the cooling water as the steam condenses. Smaller amounts escape in hot chimney gases, through friction in the turbine, and as heating in the generator coils and transformers. All of it ends up warming the surroundings.

Worked example 1: a coal-fired station

A coal-fired station in South Africa supplies 600 MW of electrical power. Its efficiency is 40%. Each kilogram of its coal releases about 25 MJ when burned (a typical value). Find (a) the input power, (b) the power wasted and (c) the mass of coal burned each second.

(a) Total input =useful outputefficiency=6000.40=1500= \dfrac{\text{useful output}}{\text{efficiency}} = \dfrac{600}{0.40} = 1500 MW

(b) Wasted =1500−600=900= 1500 - 600 = 900 MW

(c) 1500 MW is 1500 MJ every second, so the coal burned each second is

1500 MJ25 MJ/kg=60 kg\frac{1500\ \text{MJ}}{25\ \text{MJ/kg}} = 60\ \text{kg}

Answer: 1500 MW in, 900 MW wasted, and 60 kg of coal every second. Over a day, that is about 5200 tonnes.

Worked example 2: a hydroelectric station

At a dam in Ethiopia, 150 m³ of water flows through the turbines every second, falling through a height of 80 m. Take the mass of 1 m³ of water as 1000 kg and g=9.8g = 9.8 N/kg. The station is 90% efficient. Find its electrical power output.

Mass each second: 150×1000=150 000150 \times 1000 = 150\,000 kg

Energy released each second: E=mgh=150 000×9.8×80=1.176×108E = mgh = 150\,000 \times 9.8 \times 80 = 1.176 \times 10^8 J, so the input power is about 118 MW

Useful output: 0.90×117.6=105.80.90 \times 117.6 = 105.8 MW

Answer: about 110 MW. Punjab students using g=10g = 10 N/kg get 108 MW, which also rounds to about 110 MW.

In the energy resources simulation, choose Coal, press Play and follow the glowing dots from the fuel to the grid. Under the chain, the Boiler, turbine and generator line lists all three. Use the Energy resource buttons to pick Wind, and the line lists only a turbine and a generator. Pick Solar cells, and it says none of them is needed. For the generator itself, open the electromagnetic induction simulation, choose Generator and press Play. Press Faster and the Peak output card grows. The transformers and National Grid simulation shows what happens to the electricity next.

Common mistakes

  • Saying the generator makes energy. It transfers energy from the turbine's kinetic store.
  • Leaving out a stage. In a thermal station the order is fuel, boiler, steam, turbine, generator, transformer.
  • Giving every station a boiler. Wind, hydroelectric, tidal and geothermal stations have none.
  • Saying solar cells use a turbine. They produce a p.d. directly from light.
  • Saying the wasted energy disappears. It heats the surroundings, mostly through the cooling water.
  • Using an efficiency of 40 instead of 0.40 in a calculation.

Key points

  • In a thermal station, burning fuel or a nuclear reactor heats water in a boiler to make high-pressure steam.
  • The steam spins a turbine, which turns a generator.
  • The generator uses electromagnetic induction: a magnet and coils rotate relative to each other and induce an alternating p.d.
  • A step-up transformer increases the p.d., so less energy is wasted in the cables.
  • Wind, hydroelectric and tidal stations turn the turbine directly. Solar cells have no turbine or generator.
  • Thermal stations are typically about 35–45% efficient. Most of the waste leaves in the cooling water.