Skip to content

Magnetism and electromagnetism simulation

Electromagnetic Induction Simulation

A glossy bar magnet, a copper coil and a centre-zero meter, with a live oscilloscope trace of the induced e.m.f. Push, pull or drag the magnet, then switch to a spinning generator with slip rings or a split ring, a lamp, and the coil's position marked on the trace.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

Pushing the N pole of the magnet into the coil made the meter needle swing to the right and back. Now the magnet is pulled straight back out at the same speed. What does the needle do?

Try this

  1. 1Press Push and watch the meter and the trace as the N pole slides into the coil. Read the Biggest so far card (about 3.95 mV with the default settings), then press Pull. Which way does the needle swing this time, and how far?
  2. 2Set the Push and pull speed to 0.4 m/s, press Start the graph again, then press Push. Compare the height and the width of the hump with your first run at 0.2 m/s.
  3. 3Push the magnet in and wait until it stops in the middle of the coil. What does the Induced e.m.f. (or p.d.) card read now? Then drag the magnet a short way out and let go: when exactly does the needle move?
  4. 4Choose Generator under Experiment and press Play. Slow the sim to ¼× and watch the small coil symbols along the top of the trace. Is the output largest when the coil's plane is upright or flat?
  5. 5Press Slip rings to swap to a split ring while the coil turns, and watch the trace and the needle. Then press Faster twice: what happens to the Peak output card and to the number of humps each second?

Two experiments on one bench

The simulation has two set-ups, chosen under Experiment. In Magnet and coil, a bar magnet lies on the bench beside a 6 cm coil of copper wire, and the coil's two leads run to a centre-zero meter. Press Push and the magnet slides into the coil at the speed you set; Pull takes it back out. You can also drag the magnet with a finger or a mouse, or use the arrow keys. Below the bench, a green trace scrolls across a small oscilloscope screen, so every movement leaves a record you can compare.

In Generator, a rectangular coil spins between the N and S poles of two magnets. Its ends connect to the circuit through rings and carbon brushes, with the same meter and a small lamp.

What the needle is telling you

Watch the needle closely during a push. It stays on zero while the magnet is far away, swings right as the N pole enters, then drifts back to zero as the magnet settles in the middle. The reading depends on how fast the magnetic field threading the turns is changing, not on how much field there is. That is why a magnet resting inside the coil, with the most field passing through it, gives no reading at all.

Three settings make the swing bigger: a higher speed, a stronger magnet and more turns on the coil. Doubling the speed doubles the height of the hump on the trace and squeezes it into half the time. The area under the hump stays the same, because the total change of field is the same however quickly you make it.

Which way the current flows

Pulling the magnet out sends the needle the other way, and so does pushing it in again after turning it round with Flip. Leave the coil's poles switched on under Show and the ends of the coil light up as N or S while current flows. During a push, the end facing the magnet becomes the same pole as the one approaching, so the coil repels it. During a pull it becomes the opposite pole and pulls back on the magnet. Either way the coil resists what you are doing, so moving the magnet takes work, and that work is where the electrical energy comes from.

Inside the generator

Each long side of the spinning coil is a wire sweeping through the field. When the coil's plane is upright, at right angles to the field, those sides glide along the field lines and the output is zero. A quarter of a turn later the plane lies parallel to the field, the sides cross the lines head on, and the output reaches its peak. Small coil symbols along the top of the trace mark these positions as the wave is drawn. Turning faster gives taller peaks and more cycles per second.

Slip rings or a split ring

With slip rings, each end of the coil keeps its own brush, so the output reverses every half turn: alternating current. A split ring swaps the coil's connections every half turn, at the instants the output is zero, so the current in the circuit always flows one way and the trace becomes a row of humps.

The model behind the numbers

The magnet is the one from the bar magnet simulation, treated as two poles. The flux through each turn is calculated from that pole model, and the induced e.m.f. follows Faraday's law, ε=−N ΔΦΔt\varepsilon = -N\,\dfrac{\Delta\Phi}{\Delta t}. The generator uses a uniform field of 0.20 T and a coil of area 3.0×10−33.0 \times 10^{-3} m², so its peak e.m.f. is ε0=NBAω\varepsilon_0 = NBA\omega, about 0.75 V at one turn per second with 200 turns. These are typical values, not measurements, and the course note under the stage says which parts your course needs.

Check your understanding

7 questions

  1. 1.A bar magnet is held still inside a coil that is connected to a meter. What does the meter read?
  2. 2.Which change would make the induced e.m.f. smaller when a magnet is pushed into a coil?
  3. 3.The N pole of a magnet is pushed into a coil in a complete circuit. What does the end of the coil facing the magnet become?
  4. 4.Why is the e.m.f. of a turning generator coil zero when the coil's plane is at right angles to the field?
  5. 5.What does the split ring do in a simple d.c. generator (a dynamo)?
  6. 6.A generator coil is turned twice as fast. What happens to its a.c. output?
  7. 7.What are the slip rings for in an a.c. generator?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more