Skip to content

Magnetism and electromagnetism simulation

Motor Effect Simulation

A copper rod hangs between the poles of a glossy U-shaped magnet and jumps when current flows, with the force worked out from F = BIL and a left hand that turns to match. Then a coil spins on an axle, fed through a split-ring commutator, with a live graph of its turning effect.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

The copper rod in the magnet's gap is being pushed upwards. The connections to the supply are swapped, so the same current flows the other way along the rod. What happens to the force on it?

Try this

  1. 1Start with the default set-up of 0.5 T, 2 A and 0.1 m. Check the Force on the wire card using F = BIL, then press Reverse I. What happens to the rod, and does the size of the force change?
  2. 2Press Flip magnet so that the N pole moves to the right, and watch the hand in the corner of the stage turn over. Hold up your own left hand in the same pose: first finger along the field, second finger along the current.
  3. 3Switch on Turn the wire to an angle, then slide Angle between wire and field from 90° down to 0°. At which angle does the force disappear completely?
  4. 4Choose d.c. motor and press play. Raise the Current, the Turns of wire on the coil and the field (B) one at a time, and watch the Speed (model) card each time.
  5. 5Set Coil connected through to Slip rings, then press Reset and play. Why does the coil rock to and fro and stop, instead of going round?

A rod that jumps out of a magnet

The first set-up hangs a short copper rod from two thin leads, so that it sits in the gap of a U-shaped magnet. The N pole is painted red and the S pole blue, and the field lines run straight across the gap from N to S. When current flows, glowing dots drift round the circuit and the rod kicks up or down, then settles. A large orange arrow shows the force on it. Change the flux density, the current or the length of rod inside the field, and the arrow, the jump and the Force on the wire card all respond at once.

Working out the size of the force

For a wire at right angles to a field, the force is

F=BILF = BIL

where BB is the magnetic flux density in tesla, II is the current in amperes and LL is the length of wire inside the field, in metres. The default settings give 0.5×2×0.1=0.10.5 \times 2 \times 0.1 = 0.1 N. Doubling any one of the three doubles the force, while halving two of them cuts it to a quarter. Some courses write the length as a lower-case l, and the working box under the stage follows whichever course you pick.

Which way is it pushed?

Swap the supply connections with Reverse I, or turn the magnet round with Flip magnet, and the force reverses. Do both and it points the original way again. Fleming's left-hand rule predicts the direction. Hold your thumb, first finger and second finger at right angles, point the first finger along the field and the second along the conventional current, and the thumb shows the push. The illustrated hand in the corner of the stage turns to match every change, so you can check your own hand against it.

The rule only works when the current and the field are at right angles. Switch on Turn the wire to an angle and swing the rod round. The force shrinks as the rod lines up with the field and vanishes when it lies along the field lines. At other angles its size is BILsin⁡θBIL \sin\theta, which goes beyond most GCSE courses.

From a single wire to a motor

Choose d.c. motor and the gap holds a rectangular coil on an axle instead. Current flows along one long side and back along the other, so one side is pushed up while the other is pushed down, and together they turn the coil. While current flows, these two forces keep the same size all the way round. What changes is how far apart their lines of action are: widest with the coil horizontal, where the turning effect is biggest, and zero with the coil vertical, when both forces line up with the axle. The graph under the stage plots this as the coil goes round.

The job of the split ring

Left to itself, the coil would rock to a stop in the vertical position. A split-ring commutator prevents this. Its two copper halves turn with the coil, and the carbon brushes pass from one half to the other just as the coil reaches the vertical, which reverses the current. The side that has just moved across to the right is then pushed the same way as the side that was there before. Use Slow-mo to catch the sparks at the brushes as the current switches over, then choose Slip rings to see what happens without a split ring.

More current, more turns of wire or a stronger field all give a bigger turning effect, so the model motor spins faster. Its friction is chosen so that you can follow the coil by eye: a real motor would turn far more quickly.

Equations

  • Force on a current-carrying conductor

    F=BIl

    force on a conductor (at right angles to a magnetic field) carrying a current = magnetic flux density × current × length

    Open calculator →

Check your understanding

8 questions

  1. 1.A wire 0.08 m long carries a current of 3 A at right angles to a field of 0.25 T. What is the force on it?
  2. 2.In Fleming's left-hand rule, what does the second finger point along?
  3. 3.Which change makes the force on a current-carrying wire in a magnetic field act the opposite way?
  4. 4.A straight wire carrying a current lies along the magnetic field lines. What force acts on it?
  5. 5.Why does a simple d.c. motor need a split-ring commutator?
  6. 6.In which position is the turning effect on a motor's coil zero?
  7. 7.Which of these would not make a d.c. motor turn faster?
  8. 8.What is the unit of magnetic flux density?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more