What this topic covers
A toy car in Lahore, the windscreen wipers on a bus and a cordless drill in Lagos all spin because magnetic forces push on wires that carry a current. Syllabus 4.5.5 puts two of the pushes from Force on a current-carrying conductor to work.
Two pushes make a twist (Core)
Take a rectangular coil on an axle between a magnet's poles. Current travels out along one long side and returns down the other. A reversed current means a reversed force, so those sides are pushed opposite ways: one rises, the other falls. Two opposite pushes either side of an axle make a turning effect, as two hands turn a steering wheel.
Making the twist stronger (Core)
The turning effect increases with:
- extra turns of wire, since each turn adds its own pair of pushes;
- a bigger current through the coil;
- a stronger magnetic field, from a stronger magnet.
Any of these lets a motor spin faster or lift a heavier load. Turning the current round, or the field, reverses the spin.
Keeping it going: split ring and brushes (Supplement)
The coil's ends are soldered to a split ring: a metal ring on the axle, sawn into two halves insulated from each other, which turns with the coil. Two carbon brushes stay fixed and rub on opposite sides of the ring, so current passes between the supply and the spinning coil without the leads twisting.
Follow the coil round from horizontal:
- Plane along the field (horizontal): each push acts along a line as far from the axle as it can be, so the turning effect is largest.
- Approaching vertical: the pushes are just as big, but their lines of action close in on the axle, so the turning effect falls.
- Vertical: any pushes would point through the axle, so the turning effect is zero. The brushes sit on the gaps, so no current flows for an instant, and the coil coasts on its momentum.
- Just past vertical: each brush now rubs on the other half of the ring, so the coil's current flips. Whichever side has arrived on the right is pushed exactly as the previous right-hand side was, so the spin carries on in the same sense.
With fixed connections, the pushes would oppose the motion after the vertical, so the coil would swing back, wobble about the vertical and come to rest there.
Worked example: predicting the spin (Supplement)
Viewed from the front, N is on the left, so the field runs left to right. In the horizontal coil, current comes out of the page in the left-hand side and goes into it in the right-hand side.
- Left-hand side: first finger pointing right, second finger towards you, so the thumb points up.
- Right-hand side: the current runs the other way, which turns the thumb downwards.
- Result: up on the left, down on the right, so the coil spins clockwise as you see it.
Connect the supply the other way round and both pushes flip: the coil spins anticlockwise.
Motor experiments on screen
In the simulation above, switch the Set-up to d.c. motor. A 20-turn coil sits horizontal with a split ring, at Field strength 0.5 T and Current 2 A, drawn in violet.
- (Supplement) Press Play to check the worked example: the coil spins clockwise from the front.
- (Core) Increase Current, Turns of wire on the coil and Field strength in turn, watching Speed (model) rise each time. Drag Current to zero and the coil slows to rest; then set it back to 2 A.
- (Core) Press Reverse I, then Reset and Play: now it spins anticlockwise.
- (Supplement) Press Slow-mo and watch Current in side 1: it flips between "away from you" and "towards you" each half turn, and reads none within 6° of vertical, where the brushes cross the gaps. On the graph under the stage, the turning effect is highest with the coil horizontal and zero at vertical.
- (Supplement) Press Slow-mo again to return to normal speed. Set Coil connected through to Slip rings, then Reset and Play: the coil rocks and halts upright.
Card values in N and N m go beyond 0625.