Skip to content

GCSE Physics — AQA · Magnetism and electromagnetism

Electric motors

4.7.2.3Higher tier

Higher tier, for GCSE Physics and Combined Science. The two long sides of a motor's coil carry opposite currents, so the forces on them point opposite ways and turn the coil on its axle. Turning is strongest with the coil parallel to the field; a split ring reverses the current each half turn.

Loading simulation…

Symbols match your course. Open the full the motor effect simulation for more presets and teacher tools.

Spec point 4.7.2.3: Higher tier only

Motors appear on Higher tier papers only, for both GCSE Physics and Combined Science students. No new equation comes with them. The job is to show, step by step, why the forces on a coil's sides (found with Fleming's left-hand rule, 4.7.2.2) set it spinning.

The specification never names the split-ring commutator, yet a simple d.c. motor cannot keep turning without one, so learn its job. Physics-only students may also need to interpret diagrams of devices like this (4.7.2.1).

Parts of a simple d.c. motor

  • a rectangular coil of insulated copper wire on an axle
  • a magnet, so that a field crosses the coil from N to S
  • a d.c. supply, joined to the coil through two carbon brushes
  • a split ring: two copper half-rings on the axle, each joined to one end of the coil

Why the coil turns

The current flows out along one long side of the coil and back along the other. The two sides therefore carry current in opposite directions, and Fleming's rule gives them opposite forces: one up, one down. Those forces sit on opposite sides of the axle, so between them they rotate the coil.

As long as current flows, neither force changes size as the coil rotates. Their turning effect does change, because the lines of the forces move closer to the axle or further from it:

Coil's planeTurning effectWhy
Parallel to the field (flat)GreatestEach force acts at its largest distance from the axle.
Part-way roundSmallerThe forces act closer to the axle's line.
Perpendicular to the field (upright)ZeroBoth forces act straight through the axle.

The job of the split ring

Reaching the upright position, the coil is still moving, so it swings a little way past. If nothing changed, the forces would then drag it back, and after rocking to and fro it would settle upright. The split ring prevents this. Just as the coil passes upright, each brush crosses a gap onto the other half-ring. The coil's connections swap, so its current reverses. The side that has just arrived on the right now gets the push its partner had there a moment before, and the coil keeps going round the same way.

Faster, or the other way

In exam answers, the coil spins faster with a bigger current, a stronger magnet or more turns of wire, since each makes the forces larger. (Real motors are more complicated: there, a stronger magnet or extra turns can even lower the top speed, for reasons beyond GCSE.) Swapping the supply connections or turning the magnet round reverses the spin; doing both leaves it unchanged.

Worked explanation: which way does it spin?

In a diagram, the field points from an N pole at the left to an S pole at the right. The coil lies flat. Current flows into the page along the coil's left-hand side and back out of the page along its right-hand side.

  • Left-hand side: first finger right, second finger into the page, thumb down.
  • Right-hand side: opposite current, so the thumb points up.
  • Left side falling, right side rising: the coil turns anticlockwise in the diagram.

Running the motor on screen

In the simulation above, pick d.c. motor from Set-up. You get 20 turns, 0.5 T and 2 A with a Split ring. Each side of the coil has 0.05 m of wire in the field, so Force on each side shows 20×0.5×2×0.05=120 \times 0.5 \times 2 \times 0.05 = 1 N, and Turning effect now starts at its maximum, 0.04 N m, because the coil starts flat.

  1. Press Play. Viewed from the front the coil goes clockwise, and Speed (model) settles near 0.6 turns/s.
  2. Press Slow-mo and follow the brushes. Within 6° of upright they sit on the gaps: Current in side 1 reads none, Force on each side drops to 0 N and the moving dots of charge vanish. Past the gap, the current returns, reversed. Press Slow-mo again when you have seen it.
  3. The graph below the stage peaks with the coil flat and touches zero at each line marked vertical.
  4. Raise Current to 4 A (about 1.1 turns/s), then press Reverse I: the coil slows, stops and spins anticlockwise. Once in a while it stops upright with the brushes on the gaps instead. No current flows there, so no force can restart it: a real motor with a single coil can get stuck in this position too. Press Reset, then Play, to start again from flat.
  5. Select Slip rings, press Reset, then Play. With no current reversal the coil rocks and comes to rest upright.

Common mistakes

  • Saying the coil turns most strongly when upright. Its turning effect peaks when the coil's plane lies parallel to the field, and is zero when the coil stands perpendicular to it.
  • Writing that the split ring reverses the direction the coil spins. It swaps the coil's connections each half turn, so the coil's current reverses and the spin keeps the same direction.
  • Thinking the force on each side of the coil grows and shrinks as it turns. While current flows, the size of each force stays the same; only its turning effect changes, as the line of the force moves relative to the axle.
  • Explaining the motor with magnets attracting the coil. Use the motor effect: each side of the coil carries a current inside the field, so a force acts on that side.
  • Claiming that reversing the current and turning the magnet round makes the motor run backwards. Either change on its own reverses the rotation, so making both leaves the direction unchanged.
  • Leaving out why the coil gets past the upright position. It is already moving, so it carries on a little way, and then the reversed current keeps it turning.

Exam-style questions

Original questions written in the style of GCSE AQA. Try each one before you reveal the answer.

  1. 1.The diagram shows a model d.c. motor. A rectangular loop of wire, mounted on an axle, sits between the poles of a magnet. Its ends connect to a d.c. supply through two carbon brushes pressing on a split-ring commutator.

    1. (a)Explain how the motor keeps turning in the same direction.

      6 marks
      Show the answer

      Answer: Each long side of the loop carries a current across the magnetic field, so each feels a force (the motor effect). The current goes out along one side and returns along the other, so the forces point in opposite directions: upwards on one side, downwards on the other. Acting on either side of the axle, this pair of forces makes the loop rotate. When the loop is upright, both forces pass through the axle and have no turning effect, but the loop is already moving and carries on past. The split ring then swaps the loop's connections to the brushes, so the current in the loop reverses every half turn. Whichever side has just moved across feels the force its partner felt in that place, so the rotation continues in one direction. (Marked by levels: the examiner weighs up the whole explanation before choosing a level. Linking every step, including the job of the split ring, earns the top level.)

      Marking points

      • A current across a magnetic field gives a force on each long side (motor effect).
      • The current in the two long sides flows in opposite directions.
      • So the two forces point in opposite directions (one upwards, one downwards).
      • The forces act on opposite sides of the axle, so the loop rotates.
      • When upright the forces have no turning effect, but the loop keeps moving past this position.
      • The split ring reverses the current in the loop every half turn, so the forces keep turning it the same way.
  2. 2.Seen from the front, the coil of a d.c. motor turns clockwise.

    1. (a)State two different changes, either of which would make the coil turn anticlockwise.

      2 marks
      Show the answer

      Answer: Swap over the connections to the supply, which reverses the current; or turn the magnet round, which reverses the field.

      Marking points

      • Swap the connections to the power supply (reverse the current).
      • Turn the magnet round (reverse the field).
    2. (b)A student makes both of these changes at the same time. State the direction the coil turns now. Give a reason for your answer.

      2 marks
      Show the answer

      Answer: Clockwise, as before. Each change reverses the force on each side of the coil, so making both changes reverses the forces twice and leaves them as they were.

      Marking points

      • Clockwise (unchanged).
      • Each change reverses the forces, so two changes cancel out.
    3. (c)Give two ways of making the coil turn faster.

      2 marks
      Show the answer

      Answer: Any two from: more current (a higher supply p.d.); a stronger magnet; extra turns of wire on the coil.

      Marking points

      • One of: more current (higher p.d.), a stronger magnet (greater magnetic flux density) or extra turns on the coil.
      • A second, different change from that list.
  3. 3.The coil of a motor turns between the poles of a magnet. In position A, the coil's plane lies parallel to the magnetic field. In position B, the coil stands at right angles to the field.

    1. (a)In which position is the turning effect on the coil greatest? Give a reason for your answer.

      2 marks
      Show the answer

      Answer: Position A. Here the forces on the two sides act as far from the axle as they can, so their turning effect is biggest.

      Marking points

      • Position A.
      • The forces on the sides act as far from the axle as they can (greatest perpendicular distance), so their turning effect is biggest.
    2. (b)Explain why the forces on the coil have no turning effect in position B.

      2 marks
      Show the answer

      Answer: In position B both forces act along a line that passes through the axle. Forces through the axle cannot turn the coil about it.

      Marking points

      • The forces act along a line through the axle (zero distance from it).
      • So they cannot make the coil turn (no turning effect).
    3. (c)Suggest why the coil does not stop when it reaches position B.

      1 mark
      Show the answer

      Answer: It is already moving, so it keeps going past position B.

      Marking points

      • The coil is already moving (has momentum), so it carries on past B.
  4. 4.Each long side of a single-turn coil has 0.12 m of wire inside a magnetic field of flux density 0.30 T. Both long sides are at right angles to the field. The current in the coil is 2.5 A.

    1. (a)Calculate the force on one long side of the coil. Use the Physics equation sheet.

      2 marks
      Show the answer

      Answer: F = BIl = 0.30 × 2.5 × 0.12 = 0.090 N.

      Marking points

      • Substitution: F = 0.30 × 2.5 × 0.12.
      • F = 0.090 N (0.09 N).
    2. (b)Compare the force on the other long side with your answer to the previous part.

      2 marks
      Show the answer

      Answer: It has the same size, 0.090 N, but acts in the opposite direction, because the current in that side flows the opposite way.

      Marking points

      • Same size.
      • Opposite direction.
    3. (c)The coil is replaced by a coil of the same shape with 40 turns, carrying the same current. Suggest how big the force on one long side is now.

      1 mark
      Show the answer

      Answer: Each turn feels 0.090 N, so 40 × 0.090 = 3.6 N.

      Marking points

      • 3.6 N (40 × 0.090 N).

Quick check

6 questions

  1. 1.Every half turn of a d.c. motor's coil, what does the split ring reverse?
  2. 2.In which position is the turning effect on a motor's coil greatest?
  3. 3.Why are the forces on the two long sides of a motor's coil in opposite directions?
  4. 4.Which change makes a d.c. motor spin the opposite way?
  5. 5.A d.c. motor is built with slip rings instead of a split ring. What does its coil do?
  6. 6.Which parts let current reach the coil while it turns?