Skip to content

GCSE Physics — AQA · Forces

Pressure and depth in a liquid

4.5.5.1.2Higher tierPhysics only

Higher tier, GCSE Physics only. The pressure due to a column of liquid is p = hρg, given on the equation sheet. It rises with depth and with density, because the liquid above a point then weighs more. Use the difference in depth to find a difference in pressure.

Loading simulation…

Symbols match your course. Open the full liquid pressure and depth simulation for more presets and teacher tools.

Who needs this: Higher tier, physics only

Only students sitting Higher tier papers in GCSE Physics are tested on spec point 4.5.5.1.2. Foundation tier and Combined Science leave it out. You need to:

  • calculate the pressure due to a column of liquid with p=hρgp = h\rho g. It is given on the Physics equation sheet, and every question tells you the value of gg
  • explain why the pressure is greater deeper down in a liquid, and greater in a denser liquid
  • work out the difference in pressure between two depths.

Upthrust, also in 4.5.5.1.2, has its own page.

The equation

p=hρgp = h\rho g

pp is the pressure due to the liquid, in pascals (Pa). hh is the height, in metres (m), of the liquid column standing above the point, which is the depth of the point below the surface. ρ\rho is the density of the liquid in kg/m³, and gg, in N/kg, is the gravitational field strength. Air pressing on the surface adds extra pressure on top, but this equation counts only the liquid's share.

Why deeper and denser give more pressure

Think of a small flat square at some point in the liquid. The liquid directly above it forms a column resting on the square, like a pile of books on your hand.

  • Deeper: further down, the column above the square is taller. A taller column holds more liquid, so it weighs more, and that extra weight sits on the same small area.
  • Denser: each cubic metre of a denser liquid has more mass. A column of the same height weighs more, so the pressure is greater again.

You can turn this picture into the equation. A column of height hh standing on an area AA has volume AhAh, mass ρAh\rho Ah and weight ρAhg\rho Ahg. Pressure is force ÷ area, so p=ρAhg÷A=hρgp = \rho Ahg \div A = h\rho g. Because AA cancels, a wide tank and a narrow tube filled to the same depth give the same pressure. The shape does not matter either: liquid pressure acts in every direction, so a point tucked under a sloping wall or an overhang still feels the pressure for its depth.

Worked example 1: a village well. The water in a well is 12 m deep. With g = 9.8 N/kg and water at 1000 kg/m³, calculate the pressure that the water causes at the bottom of the well.

Given: h=12h = 12 m, ρ=1000\rho = 1000 kg/m³, g=9.8g = 9.8 N/kg. Equation: p=hρgp = h\rho g. Substitution: p=12×1000×9.8p = 12 \times 1000 \times 9.8. Answer: p=117 600p = 117\,600 Pa, about 1.2×1051.2 \times 10^5 Pa.

Pressure differences

Within one liquid, ρ\rho and gg do not change, so the difference in pressure between two points depends only on how far apart they are vertically. Find that difference in depth and use it as hh.

Worked example 2: a dam. The foot of a dam is 30 m below the surface of a reservoir. How much greater is the pressure there than at a point on the dam 5.0 m below the surface?

Given: difference in depth =30−5.0=25= 30 - 5.0 = 25 m, ρ=1000\rho = 1000 kg/m³, g=9.8g = 9.8 N/kg. Equation: p=hρgp = h\rho g, with hh as the difference in depth. Substitution: p=25×1000×9.8p = 25 \times 1000 \times 9.8. Answer: the pressure at the foot is 245 000 Pa (245 kPa) greater. Working out each pressure first, 294 000 Pa − 49 000 Pa, gives the same result. Engineers make dams thicker towards the base for this reason.

Using the simulation

When the simulation above loads, a tank holds 1.00 m of water and the probe hangs 0.50 m below the surface. Even before you press Play, Pressure at the probe reads 4900 Pa, and the Working line multiplies 0.50 × 1000 × 9.8.

Predict the reading at the very bottom of the tank. Then slide Probe depth to 1.00 m, or drag the probe on the stage: 9800 Pa, twice as much, because the column of water above it is twice as tall. Next set 0.20 m (1960 Pa) and then 0.70 m (6860 Pa). They differ by 4900 Pa, which is hρgh\rho g for the 0.50 m between them. The ρg card shows 9800 Pa/m, the gradient of the straight line on the Pressure against depth graph.

Return the probe to 0.50 m and pick Sea water from the Liquid menu: 5050 Pa. Cooking oil, less dense than water, gives 4510 Pa. Below the stage, The shape does not matter shows four differently shaped vessels with equal pressure at the probe's depth. Add atmospheric pressure (total) starts off; switch it on and 1.01×1051.01 \times 10^5 Pa is added at every depth. The jet speeds you see after pressing Play go beyond GCSE.

Equations

  • Pressure in a liquid

    On the equation sheet · Higher tier · Physics only

    p=hρg

    pressure due to a column of liquid = height of column × density of liquid × gravitational field strength

    Open calculator →

Common mistakes

  • Using the height of a point above the bottom of the tank as h. In p = hρg, h is the depth measured down from the surface of the liquid.
  • Thinking that a broader tank, or one with more water in it, gives more pressure at the same depth. Only h, ρ and g matter, not the shape or the amount of liquid.
  • Adding the two depths when a question asks for a pressure difference. Subtract the depths first and multiply that difference by ρg, or find both pressures and subtract them.
  • Putting a density in g/cm³ into p = hρg. Change it to kg/m³ first: 0.92 g/cm³ is 920 kg/m³.
  • Explaining the depth effect with "there is more pressure lower down", which just repeats the fact. Say why: a taller column of liquid above means more weight on each square metre.
  • Adding atmospheric pressure when the question asks for the pressure due to the liquid. p = hρg gives only the liquid's share.

Exam-style questions

Original questions written in the style of GCSE AQA. Try each one before you reveal the answer.

  1. 1.Higher tier, physics only. A water storage tank on a farm is filled to a depth of 2.5 m. In this question, g = 9.8 N/kg and the water in the tank has a density of 1000 kg/m³.

    1. (a)Calculate the pressure due to the column of water at the bottom of the tank.

      2 marks
      Show the answer

      Answer: p = hρg = 2.5 × 1000 × 9.8 = 24 500 Pa

      Marking points

      • p = 2.5 × 1000 × 9.8
      • 24 500 Pa
    2. (b)A tap is fitted to the side of the tank 0.60 m above its base. Calculate the pressure that the water causes at the tap.

      3 marks
      Show the answer

      Answer: Depth of the tap = 2.5 − 0.60 = 1.9 m. p = 1.9 × 1000 × 9.8 = 18 620 Pa, about 1.9 × 10⁴ Pa.

      Marking points

      • Depth of the tap below the surface = 1.9 m.
      • p = 1.9 × 1000 × 9.8
      • 18 620 Pa (accept 18 600 Pa or 1.9 × 10⁴ Pa).
    3. (c)Explain why the pressure at the bottom of the tank is greater than the pressure at the tap.

      2 marks
      Show the answer

      Answer: The bottom is deeper, so there is a taller column of water above it. That column has a greater weight, which presses on each square metre of the bottom.

      Marking points

      • The bottom is deeper, with a taller column of water above it.
      • So a greater weight of water acts on each unit of area.
    4. (d)The farmer replaces the tank with a much wider one, filled to the same depth. State what happens to the pressure at the bottom. Give a reason.

      2 marks
      Show the answer

      Answer: It stays the same (24 500 Pa). The pressure depends only on the depth, the density of the liquid and g, not on the width of the tank.

      Marking points

      • The pressure is unchanged.
      • It depends only on the depth and density (and g), not on the width or the amount of water.
  2. 2.Higher tier, physics only. Two tall glass cylinders stand side by side. One holds water of density 1000 kg/m³, and the other holds cooking oil of density 920 kg/m³. Both liquids are 0.25 m deep. g = 9.8 N/kg.

    1. (a)Calculate the pressure due to the oil at the bottom of its cylinder.

      2 marks
      Show the answer

      Answer: p = 0.25 × 920 × 9.8 = 2254 Pa, about 2300 Pa.

      Marking points

      • p = 0.25 × 920 × 9.8
      • 2254 Pa (accept 2250 Pa or 2300 Pa).
    2. (b)Explain why the pressure at the bottom of the water is greater than at the bottom of the oil.

      2 marks
      Show the answer

      Answer: Water is denser than the oil, so a column of water of the same height has more mass and a greater weight. That bigger weight presses on the same area.

      Marking points

      • Water has the greater density.
      • So the same height of liquid has a greater weight above each square metre (pressure is proportional to density).
    3. (c)Calculate the depth of oil that would give the same pressure as the 0.25 m of water.

      3 marks
      Show the answer

      Answer: Pressure under the water = 0.25 × 1000 × 9.8 = 2450 Pa. h = p ÷ (ρg) = 2450 ÷ (920 × 9.8) = 0.27 m.

      Marking points

      • Pressure under the water = 2450 Pa.
      • h = 2450 ÷ (920 × 9.8)
      • 0.27 m (accept 0.272 m).
  3. 3.Higher tier, physics only. A remotely operated vehicle (ROV) inspects the legs of an oil platform under the sea. Use g = 9.8 N/kg; the sea water's density is 1030 kg/m³.

    1. (a)Calculate the increase in the pressure due to the sea water when the ROV dives from 15 m to 45 m below the surface.

      3 marks
      Show the answer

      Answer: Difference in depth = 45 − 15 = 30 m. Increase = 30 × 1030 × 9.8 = 302 820 Pa, about 3.0 × 10⁵ Pa.

      Marking points

      • Difference in depth = 30 m.
      • 30 × 1030 × 9.8
      • 3.0 × 10⁵ Pa (accept 302 820 Pa or 303 000 Pa).
    2. (b)The ROV's camera looks out through a flat window of area 0.020 m². Calculate the increase in the force of the water on the window during the dive.

      2 marks
      Show the answer

      Answer: Increase in force = increase in pressure × area = 302 820 × 0.020 = 6056 N, about 6100 N.

      Marking points

      • 302 820 × 0.020 (allow their increase in pressure).
      • 6056 N or 6100 N (accept 6000 N from using 3.0 × 10⁵ Pa).
    3. (c)The ROV then travels 20 m sideways, staying 45 m below the surface. State what happens to the pressure on it.

      1 mark
      Show the answer

      Answer: It stays the same, because its depth does not change.

      Marking points

      • It stays the same (the depth is unchanged).
  4. 4.Higher tier, physics only. A student measures the pressure due to a liquid at several depths and plots pressure against depth. The best-fit line is straight and starts at the origin. At a depth of 0.40 m the pressure due to the liquid is 4900 Pa. g = 9.8 N/kg.

    1. (a)Describe the relationship between pressure and depth shown by the graph.

      1 mark
      Show the answer

      Answer: The pressure is directly proportional to the depth.

      Marking points

      • Directly proportional (a straight line through the origin).
    2. (b)Calculate the density of the liquid.

      3 marks
      Show the answer

      Answer: ρ = p ÷ (hg) = 4900 ÷ (0.40 × 9.8) = 1250 kg/m³

      Marking points

      • ρ = p ÷ (h × g)
      • 4900 ÷ (0.40 × 9.8), which is 4900 ÷ 3.92
      • 1250 kg/m³
    3. (c)Predict the pressure due to the liquid at a depth of 1.20 m.

      1 mark
      Show the answer

      Answer: Three times the depth gives three times the pressure: 3 × 4900 = 14 700 Pa.

      Marking points

      • 14 700 Pa
    4. (d)The student repeats the experiment with water, density 1000 kg/m³. Describe how the new line compares with the first one.

      2 marks
      Show the answer

      Answer: It is still a straight line through the origin, but it is less steep. Water is less dense, and the gradient of the line is ρg.

      Marking points

      • Still a straight line through the origin.
      • Less steep (smaller gradient), because water is less dense (gradient = ρg).

Quick check

6 questions

  1. 1.Which quantities does the pressure due to a liquid at a point depend on?
  2. 2.What is the pressure due to sea water (density 1030 kg/m³) at a depth of 5.0 m? Take g = 9.8 N/kg.
  3. 3.By how much is the pressure due to fresh water greater at 6.0 m than at 2.0 m? (Density 1000 kg/m³, g = 9.8 N/kg.)
  4. 4.Four containers of different shapes hold the same liquid to the same depth. Where is the pressure on the base greatest?
  5. 5.Why does the pressure in a lake increase with depth?
  6. 6.At what depth in fresh water (density 1000 kg/m³, g = 9.8 N/kg) is the pressure due to the water 49 000 Pa?