Where this fits: Higher tier, physics only
Spec point 4.5.5.1.2 also covers upthrust and floating, which only Higher tier students of GCSE Physics are examined on. You need to:
- explain upthrust using the difference in pressure between the bottom and the top of an object
- describe what decides whether an object floats or sinks.
There is no upthrust equation to learn. Calculations combine , from the equation sheet, with , which you recall, or simply subtract a newtonmeter reading from the weight.
Why a liquid pushes upwards
Pressure in a liquid increases with depth, and the bottom of an object is lower than its top, so the liquid presses harder on the bottom. Each push acts at right angles to its surface: up on the bottom, down on the top. The bigger upward push leaves a resultant force upwards: the upthrust.
The sides are pushed too, but each sideways push is matched by an equal one at the same depth on the opposite side, so they cancel. If only part of an object is under the surface, the liquid presses on its bottom but not on its top.
Worked example 1: a sensor in a lake. A sealed cylindrical sensor is 0.25 m tall, and each flat end has an area of 0.020 m². A tether holds it upright under a lake, with its upper end 0.75 m below the surface. What upthrust acts on it? (g = 9.8 N/kg; lake water 1000 kg/m³.)
Given: upper end at m, lower end at m, m². Equations: at each end, then for the difference. Substitution: upper end, Pa; lower end, Pa. The lower end has 2450 Pa more, so the upthrust . Answer: upthrust N, upwards.
Lower it further and the pressures at both ends grow equally, so the upthrust stays 49 N.
Floating and sinking
Two forces decide what happens: weight acts downwards and upthrust acts upwards.
| Forces on the object | What happens |
|---|---|
| Weight bigger than the upthrust, even fully under | Resultant force downwards: it sinks to the bottom |
| Weight smaller than the upthrust when fully under | Resultant force upwards: it rises until part of it is above the surface |
| Upthrust equal to the weight | Balanced forces: it floats at rest |
These factors decide which row applies:
- Density of the object compared with the liquid. A denser object sinks, because even fully under it gets less upthrust than its weight. A less dense object floats.
- How deep it sits. A floating object sinks in until the pressure on its bottom gives an upthrust equal to its weight. Load it and it settles deeper.
- Density of the liquid. In a denser liquid the pressure rises faster with depth, so an object needs to sink in less: it floats higher. A ship floats slightly higher in the sea than in a river.
- Shape. Steel is about eight times as dense as water, yet steel ships float. A hollow hull encloses a lot of air, so the ship as a whole is less dense than water. Squashed into a solid lump, the same steel would sink.
Using the simulation
When the simulation above opens, a 100 cm³ aluminium block hangs from a newtonmeter over a eureka can of water, with the force arrows on. Weight in air reads 2.65 N. Press Lower, under the stage, four times; each press puts another quarter of the block under. The Upthrust card climbs 0.245 N at a time to 0.980 N, and the Newtonmeter reading falls to 1.67 N.
Switch on Pressure on the top and bottom faces, which starts off, then press Lower once more to take the block 2 cm deeper. The pressure due to the water is now 588 Pa on the bottom face and 196 Pa on the top, and the resultant upward force is 1.47 N − 0.490 N = 0.980 N: no extra upthrust.
Choose Float and press Drop in. The pine cube settles with 50% under the water, where upthrust = weight = 4.90 N. Select Glycerol, which is denser, and only 40% stays under. Then pick Nylon from the cube list, go back to Water and drop it in: its 11.3 N weight beats the 9.80 N upthrust, so it sinks.