What this topic covers
A sharp knife slices a mango with a gentle push, while the back of the blade barely marks it. Topic 1.8 explains why, then looks inside liquids, where pressure grows with depth.
Pressure from a force (Core)
Pressure is force per unit area: how hard a force presses on each square metre of a surface.
- : pressure, in N/m² (or N/cm²)
- : the force pushing at right angles on the surface, in newtons (N)
- : area the force acts on, in m² (or cm²)
You need to remember this equation. Dividing newtons by cm² gives N/cm². A square metre holds 100 × 100 = 10 000 cm², so multiply by 10 000 to convert N/cm² to N/m². A square metre is also 1 000 000 mm².
Everyday examples (Core)
With the area fixed, a bigger force gives a bigger pressure: stack a second brick on the first and the pressure on the sand below doubles. With the force fixed, a smaller area raises the pressure and a larger area lowers it.
| Example | Contact area | Pressure and result |
|---|---|---|
| Knife edge, needle point | Tiny | Very large: cuts or pierces with a light push |
| Snowshoes, wide tractor tyres | Large | Small: less sinking into snow or mud |
| Wide straps on a heavy bag | Large | Small: the straps do not dig into your shoulders |
Pressure in liquids (Core)
Below a liquid's surface, the pressure rises with depth. A deeper point has a taller column of liquid above it, so more weight bears down on each square metre. That is why dam walls are thickest at the bottom.
At the same depth, a denser liquid gives a bigger pressure: sea water (about 1030 kg/m³) presses slightly harder than fresh water (1000 kg/m³). The width and shape of the container make no difference.
The liquid pressure equation (Supplement)
- : change in pressure, in pascals (Pa)
- : density of the liquid, in kg/m³
- : gravitational field strength, 9.8 N/kg
- : change in depth, in m
Remember this one too. is the vertical distance between the two levels, even along a sloping pipe. From the surface down, is the depth, and is the pressure the liquid adds to the air pressure on its surface.
Worked example 1: a loaded bookshelf (Core)
A loaded bookshelf in a school library in Accra weighs 840 N. It stands on four feet, each touching the floor over 3.5 cm². Find the pressure on the floor in N/cm² and in N/m².
In square metres, , so
Answer: 60 N/cm², which is 600 000 N/m² (60 × 10 000).
Worked example 2: a diver going deeper (Supplement)
A diver off the coast of Oman swims down from 3.0 m to 18.0 m below the surface of sea water of density 1030 kg/m³. Find the increase in pressure. Take N/kg.
Answer: about Pa (151 kPa). Using 18.0 m instead of the change in depth wrongly gives about 182 000 Pa.
Simulation tasks
In the simulation above, a 2.0 kg Brick lies flat on Dry sand, with Weight 19.6 N, Contact area 0.0200 m² and Pressure 980 Pa. The simulation uses pascals; for a Core answer, read 980 Pa as 980 N/m².
- (Core) Predict the pressure on the 50 cm² end, then press End. The weight stays at 19.6 N, but the Pressure arrows lengthen and the pressure becomes 3920 Pa: a quarter of the area, four times the pressure.
- (Core) Press Side: half the flat face's area, twice its pressure (1960 Pa).
- (Core) Press Flat, then choose Steel under The block. Same area, but the weight is 77.4 N and the pressure 3870 Pa.
- (Core) Switch to Everyday examples. The Knife compares two cases with the same 30 N push: first on the sharp edge, then on the back of the blade. The edge's area is 100 times smaller, so its pressure is 100 times bigger.
- (Core, then Supplement) In the liquid pressure and depth simulation, drag the probe deeper and watch Pressure at the probe rise, then choose Mercury under Liquid and see it jump. Supplement candidates: choose Water, set Probe depth to 0.50 m and check Pressure at the probe against Pa.