How a liquid presses
A liquid pushes on the base and walls of its container and on anything dipped into it. Recall two facts before the formula:
- Inside a liquid, the pressure at a point acts equally in all directions: up, down and sideways.
- The pressure increases with depth below the surface.
The push of a liquid on a surface is always at right angles to that surface. Make a pinhole in the side of a full plastic bottle. The thin stream of water starts out at right angles to the wall, and then gravity bends it down.
Deriving P = ρgh
Picture a flat, horizontal patch of area , a depth down in a liquid of density . The patch holds up the upright column of liquid standing on it.
- Volume of the column:
- Mass of the column:
- Weight of the column, which is the force on the patch:
- Pressure on the patch:
Put in kg m⁻³, and in metres, measured straight down from the free surface. then comes out in pascals, because
This is the pressure caused by the liquid alone. The air above the surface adds atmospheric pressure on top, which section 6.6 deals with.
What the pressure depends on
- Depth. In one liquid, . Each metre of water adds 10 000 Pa (with g = 10 m s⁻²), so the pressure due to the water 4 m down is twice its value 2 m down.
- Density. At one depth, . Mercury is 13.6 times as dense as water, so it gives 13.6 times the pressure.
- Not the area or the shape. cancelled out of the derivation. A slim pipe and a broad tank holding the same liquid to equal depths have the same pressure at the bottom. The tank holds more liquid, but its larger base shares that extra weight.
These ideas explain familiar designs. A dam wall is built thickest at its base, where the water presses hardest. The tap of a water cooler runs faster when the cooler is full than when it is nearly empty. A hospital drip bottle hangs well above the patient's arm, so the height of liquid gives enough pressure to push it into a vein.
Worked numerical 1: a canal bed
A canal carries water 4.2 m deep. What pressure does the water exert on the canal bed?
Data: , , ,
Worked numerical 2: which oil?
A gauge 1.5 m down in the oil of a storage tank reads 1.2 × 10⁴ Pa due to the oil. Find the density of the oil, taking .
Data: , ,
That is close to the density of kerosene oil.
Exploring the probe, liquids and jets
In the simulation above, a tall tank holds Water 1.00 m deep, and the probe sits 0.50 m below the surface. The Pressure at the probe card reads 5000 Pa, and the working shows P = ρ × g × h = 1000 × 10 × 0.50 = 5000 Pa.
- Drag the probe, or use the Probe depth slider, until the Probe depth card reads 1.00 m. The reading doubles to 10000 Pa. On the Pressure against depth graph, the water line is straight and passes through the origin, with gradient ρg = 10000 Pa m⁻¹.
- Look at The shape does not matter. Four connected vessels of very different widths and shapes are filled to the same depth, and the pressure at the probe's level is the same in each one.
- Choose Mercury from the Liquid menu. The probe now reads 1.36 × 10⁵ Pa, which is 13.6 times the water reading. Cooking oil gives 9200 Pa.
- Press Play to pull out the bungs. Each stream comes out at right angles to the wall, then bends down. The jets table, an extension beyond Class 9, shows the lowest jet spurting out fastest, because the pressure there is greatest. Where a jet lands also depends on how high its hole is above the tray, so judge pressure by speed, not by landing point.
- The tap starts on, keeping the level steady. Press Top up to turn it off: as the level falls, the depth above the probe shrinks and so does the reading.
Switching on Add atmospheric pressure (total) adds the push of the air, taken as 1.01 × 10⁵ Pa.