Skip to content

GCSE Physics — AQA · Electricity

Electrical power

4.2.4.1

Electrical power is the rate at which a device transfers energy, measured in watts: 1 W is 1 J each second. Recall P = VI and P = I²R, where I is the current through the device and R is its resistance. Both tiers, GCSE Physics and Combined Science, spec 4.2.4.1.

Loading simulation…

Symbols match your course. Open the full charge, current, energy and power simulation for more presets and teacher tools.

Where this fits in AQA GCSE Physics

Spec point 4.2.4.1 is examined on Foundation and Higher papers alike, and Combined Science students sit it as well as GCSE Physics students. It connects three quantities for a component: the reading on a voltmeter connected across it (the potential difference, or p.d.), the reading on an ammeter in series with it (the current) and the number of joules it transfers each second (its power). Neither power equation is printed on the equation sheet, so learn both. In the exam you may need to:

  • explain why a bigger p.d. or a bigger current gives a bigger power
  • link power to energy: a device's power is the energy it transfers in each second
  • recall P=VIP = VI and P=I2RP = I^2R, and choose the one that suits the data

Power measures how fast

Power is the rate of energy transfer. One watt (1 W) is one joule transferred every second, so a 40 W soldering iron transfers 40 J each second and a 3 kW kettle transfers 3000 J each second. Leaving a device on for longer transfers more energy, but its power stays the same.

Why p.d. times current is power

Two other results meet here. E=QVE = QV (spec point 4.2.4.2) says that one coulomb of charge, passing through a p.d. of VV volts, hands over VV joules. Q=ItQ = It (spec point 4.2.1.2) says that a current of II amps carries II coulombs past a point every second. So every second, II coulombs each hand over VV joules:

P=VIP = VI

The current-squared version

Replace VV with IRIR, using V=IRV = IR from spec point 4.2.1.3, and a second equation appears:

P=I2RP = I^2R

Here II must be the current through the resistor and RR that resistor's own resistance. Only the current is squared, so with the resistance fixed, doubling the current makes the power four times as big.

QuantitySymbolMeasured in
powerPPwatts (W)
potential differenceVVvolts (V)
currentIIamperes, or amps (A)
resistanceRRohms (Ω)

Worked example 1: a kettle on the mains

A kettle plugged into the 230 V mains draws a current of 12 A. Calculate its power.

Given: V=230V = 230 V, I=12I = 12 A

Equation: P=VIP = VI

Substitution: P=230×12P = 230 \times 12

Answer: P=2760P = 2760 W, which is 2.8 kW to 2 significant figures.

Worked example 2: a resistor on a circuit board

A current of 0.20 A passes through a 47 Ω resistor. Calculate the power transferred in the resistor.

Given: I=0.20I = 0.20 A, R=47 ΩR = 47\ \Omega

Equation: P=I2RP = I^2R

Substitution: P=0.202×47=0.040×47P = 0.20^2 \times 47 = 0.040 \times 47

Answer: P=1.88P = 1.88 W, which is 1.9 W to 2 significant figures.

Leaving out the square gives 9.4 W, an answer five times too big.

Picking the right equation

You are givenUse
p.d. and currentP=VIP = VI
current and resistanceP=I2RP = I^2R
p.d. and resistancefind II with V=IRV = IR first, then use either one

If a question gives the power and the resistance and asks for the current, rearrange to I=P/RI = \sqrt{P/R}: divide first, then take the square root.

Explore it: the power readouts

In the simulation above, the circuit view opens with a 6 V battery, a 3 Ω lamp and the switch already closed. Work out the current and the power, then compare with the Current and Power cards: 2.00 A and 12.0 W. Below the graphs, the Working box finds the power with P=VIP = VI and again with P=I2RP = I^2R, each tagged recall; a third line, from p.d. and resistance, is tagged "not on the AQA list". The What a volt means box reaches the same 12.0 W from 6 J for each coulomb and 2.00 coulombs a second.

Next, choose 2 A for 30 s at 6 V from the Examples menu: a 3 Ω resistor that gives the same 2.00 A and 12.0 W as the lamp. Then choose The same resistor on 12 V. The p.d. has doubled, so the current doubles to 4.00 A and the power rises four times, to 48.0 W. Drag Resistance of the resistor to 6 Ω: the current and the power both halve, to 2.00 A and 24.0 W, as the warning above predicts. Last, press Off under the stage. With the switch open no charge flows, so both cards drop to zero.

Equations

  • Electrical power (P = IV)

    Learn this

    P=VI

    power = potential difference × current

    Open calculator →
  • Electrical power (P = I²R)

    Learn this

    P=I2R

    power = (current)² × resistance

    Open calculator →

Common mistakes

  • Forgetting to square the current in P = I²R, or squaring the resistance instead. Work out I² first, then multiply by R.
  • Putting the supply p.d. into P = VI to find the power in just one part of a circuit, such as a cable. Use the p.d. across that part, or I²R with that part's own resistance.
  • Leaving prefixes in place: a 2.5 kW heater has P = 2500 W, and 250 mA is 0.25 A.
  • Assuming more resistance always means more power. That holds only when the current stays the same; on the same p.d., a bigger resistance takes less current and transfers less power.
  • Rearranging wrongly. I = P ÷ V, not V ÷ P, and from P = I²R the current is the square root of P ÷ R.
  • Describing power as an amount of energy. A 60 W lamp transfers 60 J every second, not 60 J in total.

Exam-style questions

Original questions written in the style of GCSE AQA. Try each one before you reveal the answer.

  1. 1.A toaster runs from the 230 V mains. The current in it is 4.0 A.

    1. (a)State the equation that links power (P), potential difference (V) and current (I).

      1 mark
      Show the answer

      Answer: P = VI, where P is the power, V the potential difference and I the current.

      Marking points

      • P = VI (allow P = IV)
    2. (b)Calculate the power of the toaster.

      2 marks
      Show the answer

      Answer: P = VI = 230 × 4.0 = 920 W

      Marking points

      • P = 230 × 4.0
      • P = 920 W
    3. (c)A larger toaster has a power of 1.38 kW. Calculate the current in this toaster when it is connected to the same supply.

      3 marks
      Show the answer

      Answer: P = 1.38 kW = 1380 W. I = P ÷ V = 1380 ÷ 230 = 6.0 A

      Marking points

      • 1.38 kW changed to 1380 W
      • I = 1380 ÷ 230
      • I = 6.0 A
  2. 2.The heating element of an electric iron has a resistance of 46 Ω. While the iron is in use, the current in the element is 5.0 A.

    1. (a)Calculate the power transferred by the heating element.

      2 marks
      Show the answer

      Answer: P = I²R = 5.0² × 46 = 25 × 46 = 1150 W

      Marking points

      • P = 5.0² × 46
      • P = 1150 W (accept 1200 W, as the data are given to 2 significant figures)
    2. (b)Calculate the potential difference across the element.

      2 marks
      Show the answer

      Answer: V = IR = 5.0 × 46 = 230 V

      Marking points

      • V = 5.0 × 46
      • V = 230 V
    3. (c)The element is replaced with one of resistance 23 Ω, which is used on the same 230 V supply. Calculate the new power of the iron.

      3 marks
      Show the answer

      Answer: I = V ÷ R = 230 ÷ 23 = 10 A. P = VI = 230 × 10 = 2300 W (or P = I²R = 10² × 23 = 2300 W). Halving the resistance on the same p.d. doubles the power.

      Marking points

      • I = 230 ÷ 23 = 10 A
      • P = 230 × 10 or P = 10² × 23
      • P = 2300 W
  3. 3.A student passes different currents through a 20 Ω resistor and works out the power transferred each time.

    1. (a)Calculate the power when the current is 0.50 A.

      2 marks
      Show the answer

      Answer: P = I²R = 0.50² × 20 = 0.25 × 20 = 5.0 W

      Marking points

      • P = 0.50² × 20
      • P = 5.0 W
    2. (b)The current is increased to 1.5 A. Without working out the new power in full, state how many times bigger it is. Give a reason.

      2 marks
      Show the answer

      Answer: 9 times bigger (45 W). The current is 3 times bigger, and for a fixed resistance the power depends on the current squared: 3² = 9.

      Marking points

      • 9 times bigger (allow 45 W)
      • For the same resistance the power depends on the current squared (3² = 9).
    3. (c)The resistor is damaged if the power in it is more than 7.2 W. Calculate the largest current it can safely carry.

      3 marks
      Show the answer

      Answer: I² = P ÷ R = 7.2 ÷ 20 = 0.36, so I = √0.36 = 0.60 A

      Marking points

      • I² = 7.2 ÷ 20
      • I² = 0.36
      • I = 0.60 A
  4. 4.A 2.3 kW heater is plugged into an extension lead. The current in the lead is 10 A. The copper wires inside the lead have a total resistance of 0.15 Ω.

    1. (a)Calculate the power transferred by heating in the wires of the lead.

      2 marks
      Show the answer

      Answer: P = I²R = 10² × 0.15 = 15 W

      Marking points

      • P = 10² × 0.15
      • P = 15 W
    2. (b)A student uses P = VI with V = 230 V and I = 10 A to find the power heating the lead, and gets 2300 W. Explain why this is wrong.

      2 marks
      Show the answer

      Answer: 230 V is the p.d. of the supply, and almost all of it is across the heater, not across the wires of the lead. So 230 V × 10 A gives the power of the heater, not the much smaller power heating the lead.

      Marking points

      • 230 V is not the p.d. across the wires of the lead (it is across the heater / supply).
      • So the result is the heater's power, not the power heating the lead.

Quick check

6 questions

  1. 1.A lamp connected to a 12 V supply has a current of 0.50 A in it. What is its power?
  2. 2.The current through a fixed resistor is doubled. What happens to the power transferred in the resistor?
  3. 3.A 4.0 Ω resistor carries a current of 3.0 A. What power does it transfer?
  4. 4.Which of these is the same as one watt?
  5. 5.A 2.5 kW kettle is connected to the 230 V mains. What is the current in it, to 2 significant figures?
  6. 6.Heaters X and Y are each connected to the same 230 V supply. Heater X has a smaller resistance than heater Y. Which statement is correct?