Skip to content

How to Calculate Efficiency: Formula, Percentages and Worked Examples

Step-by-step efficiency calculations for a motor, a kettle, two lamps and a power station: energy and power versions, decimals and percentages, rearranging, and why no device can beat 100%.

Published · 6 min read

On this page

Efficiency tells you what fraction of the energy put into a device ends up doing the job you want. To calculate it, divide the useful output by the total input:

efficiency=useful output energy transfertotal input energy transfer\text{efficiency} = \frac{\text{useful output energy transfer}}{\text{total input energy transfer}}

You can use power instead of energy, because power is just energy transferred per second:

efficiency=useful power outputtotal power input\text{efficiency} = \frac{\text{useful power output}}{\text{total power input}}

The answer is a decimal, such as 0.25. Multiply by 100 to give a percentage: 0.25 is 25%. Efficiency has no unit, because the units on the top and bottom cancel. It cannot exceed 1 (100%), because a device cannot give out more energy than it takes in.

What do the parts of the formula mean?

  • Total input: all the energy (or power) supplied to the device. For a motor or a lamp, this is the electrical energy it takes from the supply.
  • Useful output: the energy (or power) that goes where you want it. For a lamp, that is the light. For a kettle, it is the energy that heats the water.
  • Wasted energy: total input − useful output. It is usually dissipated by heating the surroundings, and sometimes by sound.

Many books use the Greek letter η (eta) for efficiency.

How do you calculate efficiency step by step?

  1. Find the total input, in joules or watts.
  2. Find the useful output. You may need another equation first, such as E=PtE = Pt, Ep=mghE_p = mgh or ΔE=mcΔθ\Delta E = mc\Delta\theta.
  3. Check that both values are in the same units: J and J, or W and W.
  4. Divide the useful output by the total input.
  5. Multiply by 100 if you want a percentage.
  6. Check that your answer is no more than 1 (or 100%).

Worked example 1: an electric winch

A small electric winch on a building site in Doha lifts a 40 kg bucket of cement up through 12 m. The motor takes in 6000 J of energy electrically. Find its efficiency, using g = 9.8 N/kg.

Given: m = 40 kg, h = 12 m, g = 9.8 N/kg, total input = 6000 J

Useful output: the gain in gravitational potential energy, Ep=mgh=40×9.8×12=4704 JE_p = mgh = 40 \times 9.8 \times 12 = 4704\ \text{J}

Equation: efficiency=useful outputtotal input\text{efficiency} = \dfrac{\text{useful output}}{\text{total input}}

Substitution: efficiency=47046000=0.784\text{efficiency} = \dfrac{4704}{6000} = 0.784

Answer: 0.78, or 78% (2 significant figures)

The other 1296 J warms the motor, the cable and the pulley, and some is carried away as sound.

Worked example 2: a kettle

A 2.4 kW kettle in Glasgow heats 1.2 kg of water from 20 °C to 100 °C in 3.0 minutes. The specific heat capacity of water is 4200 J/kg °C. Find the efficiency of the kettle.

Given: P = 2400 W, t = 3.0 min = 180 s, m = 1.2 kg, Δθ = 100 − 20 = 80 °C

Total input: E=Pt=2400×180=432 000 JE = Pt = 2400 \times 180 = 432\,000\ \text{J}

Useful output: ΔE=mcΔθ=1.2×4200×80=403 200 J\Delta E = mc\Delta\theta = 1.2 \times 4200 \times 80 = 403\,200\ \text{J}

Substitution: efficiency=403 200432 000=0.933\text{efficiency} = \dfrac{403\,200}{432\,000} = 0.933

Answer: 0.93, or 93% (2 significant figures)

The remaining 28 800 J warms the kettle's body and the surrounding air.

Worked example 3: filament lamp or LED?

Suppose a filament lamp takes in 60 W and gives out 3.0 W as visible light. An LED lamp gives out the same 3.0 W of light from an input of only 8.0 W. These are example values, and real lamps vary. Compare their efficiencies.

Filament lamp: efficiency=3.060=0.050\text{efficiency} = \dfrac{3.0}{60} = 0.050, or 5.0%

LED lamp: efficiency=3.08.0=0.375\text{efficiency} = \dfrac{3.0}{8.0} = 0.375, or 38% (2 significant figures)

Answer: the LED is 7.5 times as efficient. The filament lamp wastes 57 W by heating, but the LED wastes only 5.0 W.

This is why many countries have phased out filament lamps. India's national LED programme alone has distributed hundreds of millions of low-cost LED bulbs.

How do you rearrange the efficiency equation?

Questions often give you the efficiency and ask for an input or an output. First change any percentage into a decimal by dividing by 100: 38% becomes 0.38. Then use:

useful output=efficiency×total input\text{useful output} = \text{efficiency} \times \text{total input} total input=useful outputefficiency\text{total input} = \frac{\text{useful output}}{\text{efficiency}}

Worked example 4: a power station

A coal-fired power station unit in India has an efficiency of 38%. Its electrical output power is 660 MW. Find the input power from the burning coal and the power wasted.

Given: efficiency = 38% = 0.38, useful power output = 660 MW

Equation: total input=useful outputefficiency\text{total input} = \dfrac{\text{useful output}}{\text{efficiency}}

Substitution: total input=6600.38=1737 MW\text{total input} = \dfrac{660}{0.38} = 1737\ \text{MW}

Answer: about 1700 MW (2 significant figures)

Wasted power: 1737 − 660 = 1077 MW, or about 1100 MW. Most of it heats the cooling water, the air above the cooling towers and the gases leaving the chimney.

So this station wastes more power than it delivers. That is normal for coal-fired stations.

What is the efficiency of a chain of devices?

When energy passes through several devices in turn, multiply their efficiencies as decimals. Suppose the electricity from the station above travels through the grid, which delivers 92% of it, and then lights the LED lamp from Example 3. The overall efficiency, from coal to light, is:

0.38×0.92×0.375=0.1310.38 \times 0.92 \times 0.375 = 0.131

That is about 13%. Roughly one joule in every eight from the coal ends up as light in the room.

How do you find efficiency from a Sankey diagram?

On a Sankey diagram, arrow widths stand for amounts of energy. Read the width of the useful arrow and the width of the input arrow, then divide. For example, if the input arrow is 20 squares wide and the useful arrow is 7 squares wide, the efficiency is 7 ÷ 20 = 0.35, or 35%. You do not even need to know the energy per square, because it cancels.

Why can efficiency never be more than 100%?

Energy cannot be created. The useful output is only part of the total input, so it can never be bigger than the input. An efficiency of exactly 100% would mean no energy is wasted at all. Every real device has some friction, some electrical resistance or some sound, so it always falls short.

A few devices come close. Large transformers can reach about 99%. An electric heater is close to 100% efficient, because heating the room is its job.

If your answer is above 100%, you have probably divided the input by the output, or mixed kJ with J.

How can efficiency be improved?

  • Lubricate moving parts, so less energy is wasted by friction.
  • Insulate, so less energy escapes by heating. A kettle with a double wall, or a lagged hot-water tank, keeps more energy in the water.
  • Use LEDs instead of filament lamps.
  • Use low-resistance wires, so cables heat up less.
  • Use the waste heat. Some power stations in Denmark pipe their hot water to warm nearby homes.

To practise these ideas, try the power and efficiency simulation. For more on stores and pathways, open the energy stores and transfers simulation as well.

Common mistakes

  • Dividing the input by the output. That gives an answer above 1.
  • Mixing units, such as kJ with J, or kW with W.
  • Putting a percentage into a rearranged equation. Use 0.38, not 38.
  • Dividing an energy by a power. Use E = Pt to turn the power into an energy first.
  • Forgetting to change minutes into seconds when you use E = Pt.
  • Giving efficiency a unit. It has none.
  • Rounding too early. Keep full values until the last step.

Key points

  • Efficiency = useful output ÷ total input, using energies or powers.
  • Multiply the decimal by 100 to get a percentage.
  • Rearrange: useful output = efficiency × total input. Use the decimal form.
  • Wasted energy = total input − useful output, and is usually dissipated by heating.
  • Efficiency can never be more than 100%, because energy cannot be created.
  • Lubrication, insulation, LEDs and using waste heat all improve efficiency.