Skip to content

Energy simulation

Energy Stores and Transfers Simulation

Five everyday events, from a kettle to a bungee jump, with glowing tanks showing the energy in each store, a Sankey diagram drawn to scale and the efficiency worked out from the physics. No energy is ever created or destroyed.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

A 2000 W kettle is switched on for 150 s, so 300 kJ is transferred to it electrically. How much of that energy ends up in the water?

Try this

  1. 1Start with the Electric kettle at 2000 W for 150 s. Cover the Useful readout and guess how much of the 300 kJ will reach the water. Then press play and compare your guess with the Useful readout.
  2. 2Choose Car braking to a stop and note the Energy in. Then move Speed when braking starts from 15 m/s to 30 m/s. By what factor does the energy dissipated go up?
  3. 3Choose Bungee jump and press each Show button under Energy at key moments. At Cord just tight, Lowest point and Nearly still, which tank holds the most energy?
  4. 4Choose Ball thrown straight up and switch Air resistance off. Note the height at the top, then switch it back on and find where the missing energy has gone.
  5. 5Choose Battery torch left on and swap the Bulb between Filament and LED. The batteries hold the same energy each time, so what changes in the Sankey diagram?

What you can explore

Pick one of five events and press play. On the left, an illustrated scene acts it out: a kettle steams on a worktop, a car squeals to a halt with glowing brake discs, a jumper drops from a bridge on an elastic cord, a ball flies up and back down, and a torch shines until its batteries are flat. On the right, glass tanks fill and drain as energy moves from one place to another. Every tank uses the same scale, so you can compare them at a glance.

Below the stage, a stacked graph tracks each store through the whole event, and a table lists the amounts at key moments. Press Show on any column to jump the scene to that instant.

Different courses, different words

Physics teachers describe the same event in more than one way. Choose your course with the symbol switcher and the labels change to match it. GCSE students see energy stores, such as the thermal store of the water, with energy moving mechanically, electrically, by heating or by radiation. Cambridge IGCSE labels use internal (thermal) and elastic (strain). Punjab Class 9 labels talk about forms of energy changing from one form into another. The physics underneath is identical.

Reading the Sankey diagram

Think of it as a flow chart drawn to scale. The arrow on the left carries everything that went in. It splits into a useful arrow that carries straight on and wasted arrows that bend away. Widths are proportional to energy, so the branches always add up to the arrow they came from.

Efficiency compares the two ends:

efficiency=useful outputtotal input\text{efficiency} = \frac{\text{useful output}}{\text{total input}}

You get a decimal between 0 and 1; multiply by 100 for a percentage. The readouts give both.

Numbers from physics, not guesses

Each event is calculated rather than invented. The kettle's input is E=PtE = Pt. The water's share is ΔE=mcΔθ\Delta E = mc\Delta\theta, and the rest warms the kettle and leaks into the room at a rate that grows as the kettle gets hotter. That is why a slow boil wastes a larger fraction than a fast one.

The car starts with Ek=12mv2E_k = \frac{1}{2}mv^2. The brakes, rolling resistance and air resistance each take the work done against them, worked out from the exact motion. Because speed is squared, doubling it quadruples the energy that has to be dissipated. Switch on regenerative braking to see some of it saved in the battery instead.

The bungee jump uses Ep=mghE_p = mgh with the value of gg from your course. Watch the kinetic tank swell while the cord is slack, then the elastic tank take over as the cord stretches. At the lowest point the jumper is momentarily still, so the kinetic tank is empty.

The thrown ball meets air resistance that grows with the square of its speed, so it reaches a lower top than the textbook height and comes back to the hand more slowly than it left. The torch runs at a steady power until its batteries are flat, which shows plainly that an LED turns a bigger share of the same chemical energy into light.

A few values, such as how quickly the kettle loses energy or how much light a bulb gives out, are example values. The model notes under the graphs list each one. However they are chosen, the books always balance. At every moment the tanks add up to the energy there was at the start or, for the kettle, to the energy supplied so far.

Equations

  • Efficiency (energy)

    η=100EoutEin

    efficiency = useful output energy transfer ÷ total input energy transfer (× 100 for a percentage)

    Open calculator →

Check your understanding

8 questions

  1. 1.A 1500 W heater is switched on for 60 s. How much energy is transferred to it electrically?
  2. 2.A motor is supplied with 800 J and does 600 J of useful work. What is its efficiency?
  3. 3.A car brakes from a steady speed to a stop on a level road. Which energy decreases?
  4. 4.In a Sankey diagram, what does the width of each arrow represent?
  5. 5.A ball is thrown straight up and air resistance is too small to matter. At the very top of its flight, what is true?
  6. 6.A 60 kg bungee jumper falls 40 m to the lowest point of a jump. Taking g as 10 N/kg, how much gravitational potential energy has been lost?
  7. 7.A kettle is supplied with 300 kJ and the water gains 255 kJ. How much energy is wasted?
  8. 8.Why can no real machine have an efficiency greater than 1?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more