Skip to content

Energy simulation

Power and Efficiency Simulation

Two climbers or two winch motors race through the same height while their energy–time graphs draw live, so you can measure power as a gradient. Then a crane lifts bricks with a motor whose efficiency you choose, shown on a to-scale Sankey diagram.

Loading simulation…
Show symbols for

Predict first

Question 1 of 3

Two climbers, each 50 kg, go up the same 10 m of stairs. Climber A takes 20 s and Climber B takes 10 s. How does B's power compare with A's?

Try this

  1. 1Press play on the default Stairs race: both climbers are 50 kg and climb 10 m, but Climber B takes 10 s instead of 20 s. Cover the table, predict how B's power will compare with A's, then press play and check the Power row.
  2. 2Choose Climber B under Gradient tool measures, then slide the gradient tool along B's line on the Energy transferred against time graph. Does the gradient match B's power in the table? What happens to it after B reaches the top at 10 s?
  3. 3Choose Heavier climber, slower to the top from the Set-up menu. Cover the table and the result line, decide which climber has the greater power, then press play and use Gradient tool measures to compare the two lines.
  4. 4Switch What to explore to Motor efficiency and press play. Watch the three meters beside the crane fill, then flip the Sankey diagram between Energy (whole lift) and Power (each second). What changes and what stays the same?
  5. 5Keep the load, the height and the time fixed, and move Motor efficiency from 40% to 80%. Which of the six readouts change, and by what factor?

What this simulation shows

There are two scenes. In the power race, two climbers rise through exactly the same height, or two winch motors haul crates up a shaft if you switch the racers. You choose each racer's mass and the time it takes to reach the glowing finish line, then watch them go. In the motor efficiency scene, a tower crane on a building site lifts a pallet of bricks, and you decide how efficient its electric motor is.

Power in the stairs race

Rising through a height hh adds mghmgh to a racer's gravitational potential energy. Power is the rate at which that energy is transferred:

P=Et=mghtP = \frac{E}{t} = \frac{mgh}{t}

With the energy in joules and the time in seconds, the power comes out in watts. A watt means a joule every second and a kilowatt means a thousand of them, so the table gives each power both ways.

The default race is the textbook comparison. Both climbers are 50 kg and climb 10 m, so each gains the same energy, yet Climber B needs only half the time and so develops double the power. Next, try the heavier climber who is slower to the top. Arriving first does not guarantee the bigger power: a racer with twice the mass gains twice the energy, so can take almost twice as long and still come out ahead.

Lifting at a steady speed, the upward force equals the weight, so the work done is also mghmgh. Writing P=W/tP = W/t therefore gives exactly the same answer, and some courses lead with that form.

Gradients on the energy–time graph

Each racer's line climbs steadily while they are on the stairs and goes flat the moment they arrive. A steeper line means more joules every second, so the gradient is the power. Choose a racer under Gradient tool measures and drag along that line: the reading matches the power in the table, in watts, or in kilowatts when the axis is in kilojoules. After the finish the gradient drops to zero, because nothing more is being transferred.

Efficiency and the crane motor

No motor turns all of its electrical input into useful output. Some is dissipated by heating, mostly in the coils of wire and in the gears and bearings, and it spreads into the surroundings. Efficiency compares the useful output with the total input:

efficiency=useful energy outtotal energy in=useful power outtotal power in\text{efficiency} = \frac{\text{useful energy out}}{\text{total energy in}} = \frac{\text{useful power out}}{\text{total power in}}

Both versions give the same number, because the useful and total energies are transferred over the same time. Multiply by 100 for a percentage. The three meters beside the crane fill as the load rises, and the energy in always equals the useful energy plus the wasted energy, so nothing is created or destroyed.

The Sankey diagram, two ways

The Sankey diagram draws each transfer as an arrow whose width is in proportion to what it carries. Flip it between energy for the whole lift and power for each second. The numbers change but the shape does not, which shows at a glance why the two efficiency equations agree. The diagram always draws the input arrow at the same width, so a better motor narrows the wasted arrow and widens the useful one. The useful output itself does not change for the same lift; what falls is the input the motor needs.

About the model

Everything rises at a steady speed, so kinetic energy stays constant during the lift; the brief speed-up and slow-down are ignored. For climbers, only the energy gained by the gravitational store is counted. Real muscles waste a large share of the energy they use, so energy leaves a climber's chemical store several times faster than the power shown here. The motor's efficiency is a model value you choose, not a measurement of a real crane.

Equations

  • Power and energy transferred

    P=Et

    power = energy transferred ÷ time

    Open calculator →
  • Power and work done

    P=Wt

    power = work done ÷ time

    Open calculator →
  • Efficiency (energy)

    η=100EoutEin

    efficiency = useful output energy transfer ÷ total input energy transfer (× 100 for a percentage)

    Open calculator →
  • Efficiency (power)

    η=100PoutPin

    efficiency = useful power output ÷ total power input (× 100 for a percentage)

    Open calculator →

Check your understanding

8 questions

  1. 1.A student of mass 60 kg runs up stairs with a vertical height of 4.0 m in 6.0 s. Taking g = 9.8 N/kg, what useful power does the student develop?
  2. 2.What does the gradient of a graph of energy transferred against time tell you?
  3. 3.An electric winch takes in 500 J of energy electrically and transfers 350 J to the gravitational store of its load. What is its efficiency?
  4. 4.Two identical motors lift identical loads through the same height. Motor X takes 8 s and motor Y takes 4 s. Which statement is correct?
  5. 5.A crane motor has a useful power output of 1.2 kW and an efficiency of 0.60. What is its total power input?
  6. 6.Which of these is the same as one watt?
  7. 7.Why can no real motor have an efficiency of 100%?
  8. 8.A lift car of mass 1500 kg rises 20 m in 25 s at a steady speed. Using g = 10 N/kg, find the useful power its motor delivers.

For teachers

Embed it in your site or open it full-screen for the projector.

Read more