How Ripple Tanks Show Wave Behaviour: Measuring Ripples, Reflection, Refraction and Diffraction
Learn how a ripple tank works, how to measure the wavelength, frequency and speed of ripples for the required practical, and what the tank shows about reflection, refraction in shallow water and diffraction through gaps. With worked examples and the common exam traps.
Published · 7 min read
On this page
A ripple tank is a shallow tray of water with a clear bottom and a lamp above it. A vibrating bar or dipper taps the water and sends out a steady stream of ripples. Each crest acts like a weak lens and focuses the light, so the ripples appear as bright lines on a sheet of white paper under the tank.
Because you can see many wavefronts at once, the tank lets you measure a wave's wavelength, frequency and speed. It also shows what waves do when they meet a barrier, a change of depth or a gap: they reflect, refract and diffract.
What is in a ripple tank?
| Part | What it does |
|---|---|
| Tray with a glass bottom | Holds water a few millimetres to a centimetre deep |
| Straight bar or small dipper | Makes straight ripples (bar) or circular ripples (dipper) |
| Motor or vibration generator | Shakes the bar; its setting controls the frequency |
| Lamp above the tank | Projects the pattern of ripples onto the paper below |
| Sloping or foam-lined edges | Soak up ripples, so they don't bounce back across the tank |
| Glass plate and barriers | Make a shallow region, a reflecting wall or a gap |
How do you measure the wavelength, frequency and speed?
This is the ripple tank half of an AQA required practical. The skill being tested is choosing a method that suits each measurement.
- Wavelength: ripples move too fast to measure one at a time. Lay a ruler on the paper and measure across ten wavelengths, then divide by ten. A photo with the ruler in the picture freezes the pattern for you.
- Frequency: count the waves passing a mark on the paper in 10 seconds, then divide by 10. With a signal generator, you can read the frequency from its display. Low frequencies are much easier to count.
- Speed: use , explained in our post on wave speed. As a check, time one ripple crossing a measured distance and use speed = distance ÷ time.
A stroboscope that flashes at the same frequency as the ripples makes them seem to stand still. A slow-motion phone video does a similar job.
Worked example 1: ripples in Nairobi
A student in Nairobi sets the vibrator to 8.0 Hz. On the paper, ten wavelengths span 31 cm. Find the speed of the ripples.
Wavelength: cm m
Equation:
Substitution:
Answer: m/s (2 significant figures)
As a check, the student times one ripple across 40 cm of the tank and gets 1.6 s. Then m/s, which agrees.
What happens when ripples hit a barrier?
Put a straight barrier in the water. Straight ripples that hit it head-on bounce straight back. Ripples that arrive at an angle leave at the same angle on the other side of the normal, the line at right angles to the barrier. So the angle of incidence equals the angle of reflection.
Reflection changes only the direction of travel. The ripples are still in the same water, so their speed, frequency and wavelength all stay the same.
Why do ripples change direction in shallow water?
Lay a glass plate on the bottom of the tank, so the water above it is shallower. Ripples travel more slowly in shallower water. As they cross onto the plate:
- the frequency stays the same. Every ripple that reaches the edge of the plate must also leave it. None can pile up there or vanish, so the number passing each second does not change.
- the speed drops, so the wavelength gets shorter. Since , the bright lines bunch closer together over the plate.
- the direction changes if the ripples arrive at an angle. The part of each wavefront that crosses first slows down, while the rest is still moving fast in the deep water. The wavefront swivels, and the ripples turn towards the normal.
Ripples that cross the edge head-on keep their direction, but they still slow down, and their wavelength still shortens.
Worked example 2: over the glass plate
The ripples from worked example 1 cross onto a glass plate. Above it, their wavelength shrinks to 2.4 cm. Find their speed in the shallow water.
Frequency: unchanged, so Hz
Equation: , with m
Substitution:
Answer: m/s (2 significant figures). The ripples have lost about a quarter of their speed.
Light behaves in the same way at the edge of a glass block. In the refraction simulation, press Air → glass: the ray turns towards the normal as it enters the slower material. The line under the controls shows that light travels at only about m/s in glass.
What decides how much ripples spread through a gap?
Leave a gap between two barriers. Straight ripples that pass through it spread out into the water behind the barriers. This spreading is diffraction.
- A gap about one wavelength wide: the ripples spread out strongly, and the wavefronts beyond it are almost semicircles.
- A gap many wavelengths wide: most of the wave carries straight on, and only the ends of each wavefront curve a little.
- An edge: ripples passing the end of a single barrier bend round into the calm water behind it. Longer wavelengths bend round more.
Diffraction changes the shape and direction of the wavefronts, but not their speed, frequency or wavelength. It explains why you can hear a friend talking round a corner but not see them. Many everyday sounds have wavelengths of around a metre, similar to a doorway. Light has wavelengths of less than a millionth of a metre, so it hardly spreads at all.
To practise the measurements first, open the transverse and longitudinal waves simulation. Press Play, then Ruler, and line up markers A and B with two crests next to each other to measure one wavelength. Press Count to time several waves reaching the tracked particle: the number of waves divided by the time gives the frequency. You can also try the ripple tank simulation.
Common mistakes
- Saying the frequency changes in shallow water. It doesn't. Only the speed and the wavelength fall.
- Measuring a single wavelength. Measure across ten and divide, for a more accurate result.
- Counting bright lines instead of gaps. Ten wavelengths span eleven bright lines.
- Thinking waves always turn at a boundary. Head-on, only the speed and the wavelength change.
- Saying a gap changes the wavelength. Diffraction changes only the shape and direction of the wavefronts.
- Expecting most spreading from a wide gap. The spreading is greatest when the gap is close to one wavelength.
Key points
- A ripple tank shows wavefronts as bright lines on paper under the tank, so you can see and measure them.
- Measure the wavelength across several waves, find the frequency by counting or from the signal generator, and use .
- Reflection: the angle of incidence equals the angle of reflection, and the speed, frequency and wavelength do not change.
- Refraction: ripples slow down in shallow water, and their wavelength shortens while their frequency stays the same. They change direction if they arrive at an angle.
- Diffraction: waves spread through a gap or round an edge, most strongly when the gap is about one wavelength wide.