Skip to content

Waves and sound simulation

Ripple Tank Simulation

A virtual ripple tank with a motor-driven bar or dippers. Bounce ripples off a barrier, slow them over a glass plate, squeeze them through a gap, overlap two sets of circles, and measure wavelength and frequency as in the required practical.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

The motor runs at 5.0 Hz and the bright lines (the crests) on the water are 5.0 cm apart. The motor is turned up to 10 Hz and the water depth stays the same. How far apart are the crests now?

Try this

  1. 1Press Play in the Measure set-up and wait until the ripples reach the far beach. Press Strobe to freeze them, move markers A and B onto two bright lines several gaps apart, and set Wavelengths from A to B to the number of gaps.
  2. 2Press Count and let 10 s of tank time pass while the cork bobs. Divide the number of waves by 10 for the frequency, then multiply it by your wavelength in metres and compare the answer with 0.25 m/s.
  3. 3Choose Refraction. With the angle of incidence at the plate set to 40°, watch the ripples' direction of travel swing towards the normal as they slow from 0.25 m/s to 0.15 m/s. Tap the water over the plate to move the cork there and press Count: the frequency is still 5.0 Hz.
  4. 4Choose Gap. At 10 Hz the ripples are 2.5 cm apart, as wide as the gap, and they fan out in curved fronts. Drag Gap width up to 10 cm and watch most of them carry straight on.
  5. 5Choose the Two dippers set-up. Solid guide lines join places where the path difference is a whole number of wavelengths; tap the water on a dashed line and watch the cork stay almost still.

A tank seen from above

The stage shows a shallow tank from directly overhead, like the shadow picture a real ripple tank throws onto paper below it. A motor drives a straight bar, or one or two dippers, up and down. Each crest acts as a weak lens, gathering the lamp's light into a bright line, and each trough spreads it into a darker band. Gauze beaches soak up ripples at the edges.

The model water is about 6 mm deep, where ripples travel at 0.25 m/s; over the glass plate it is about 2 mm deep and they slow to 0.15 m/s. The motor alone sets the frequency, from 4 to 10 Hz.

Measuring wavelength, frequency and speed

The Measure set-up follows the required practical. Ripples race past too quickly to measure by eye, so switch on the strobe: it flashes once per wave, catching each crest exactly where the one before it stood, so the pattern seems to stand still. Put marker A on one bright line and marker B on another several lines further on, then count the gaps between them rather than the lines. Measuring across many wavelengths makes a slip at either end matter less.

For the frequency, press Count. A stopwatch runs for ten seconds of tank time and adds one for every crest that lifts the cork; divide the tally by ten. Or pin two neighbouring crests on the cork's height graph to read the period, then take its reciprocal. Multiply your frequency in hertz by your wavelength in metres, not centimetres, and compare the product with 0.25 m/s.

Reflection and refraction

In the Reflection set-up a metal strip stands at a slant across the ripples. The guides draw the normal, at right angles to the strip. The incoming and outgoing ripples make equal angles with it, on opposite sides.

In the Refraction set-up the glass plate is a raised step in the floor of the tank. The ripples keep the bar's frequency but cover less ground in every cycle, so the bright lines crowd together: lines 5.0 cm apart in the deep part close up to 3.0 cm over the plate at 5 Hz. When the edge is slanted, one end of each front reaches the shallow water and slows first, so the front swings round to lie more nearly along the edge, and the direction of travel turns towards the normal. With the edge parallel to the ripples, only their spacing changes.

Gaps and edges

Make the gap match the wavelength and the ripples leave it as curved fronts spreading behind the barrier. Widen it to four wavelengths and most of the energy travels straight on as a beam whose ends curve only slightly. Lowering the frequency at a fixed gap does the same as narrowing it: what matters is the gap compared with the wavelength. At a single edge, ripples with a longer wavelength curl further round into the shadow.

Two dippers

With two dippers moving in step, their circles overlap. Along some lines crests always meet crests and the water swings strongly; along others a crest from one dipper always meets a trough from the other, and the water barely moves. The still lines are where one dipper is half a wavelength, or one and a half, further away than the other. This goes beyond GCSE and IGCSE.

AQA GCSE uses the tank in required practical 8; diffraction and interference are not on that specification. Cambridge IGCSE uses it for reflection, refraction and diffraction (Core), adding how gap width and wavelength matter (Supplement). Punjab students meet it in Class 10, Chapter 12.

Equations

Check your understanding

8 questions

  1. 1.In a ripple tank, 10 crests pass a point in 2.0 s and neighbouring crests are 3.0 cm apart. What is the speed of the ripples?
  2. 2.Straight ripples pass from deep water into shallower water. What happens?
  3. 3.Why does a ripple tank practical use a strobe lamp?
  4. 4.Ripples hit a straight barrier with an angle of incidence of 35°. What is the angle of reflection?
  5. 5.Ripples with a wavelength of 2 cm reach a barrier. Which gap makes them spread out the most?
  6. 6.In a frozen ripple pattern, a student measures 21 cm from the first to the eighth bright line. What is the wavelength?
  7. 7.Two dippers move up and down in step. At point P, the ripples from one dipper have travelled 1.5 wavelengths further than those from the other. What happens at P?
  8. 8.The motor's frequency is halved and the depth of the water does not change. What happens to the wavelength of the ripples?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more