Electromagnetic Induction Explained: Moving Magnets, Generators and Microphones
Learn how a changing magnetic field induces a potential difference, the three ways to make it bigger, why the induced current always opposes the change, and how a.c. generators, dynamos and microphones work.
Published · 8 min read
On this page
Electromagnetic induction means using a magnetic field to produce a potential difference (p.d.). It happens when a wire and a magnetic field move relative to each other, or when the magnetic field through a coil changes. The p.d. appears between the two ends of the wire. Connect those ends into a complete circuit, and a current flows. Another name for this is the generator effect.
Push a bar magnet into a coil joined to a sensitive meter, and the needle flicks. Pull it out, and the needle flicks the other way. Hold it still, and nothing happens, however strong the magnet. What matters is change: moving the magnet, moving the coil or changing the strength of the field.
Nearly every power station, apart from solar farms, generates electricity this way.
How can you show electromagnetic induction in the lab?
Connect a coil of insulated wire to a centre-zero galvanometer, a meter whose needle can swing either way. Then try these:
- Push the N pole of a magnet into the coil. The needle flicks one way, then returns to zero.
- Hold the magnet still inside the coil. The needle reads zero.
- Pull the magnet out. The needle flicks the opposite way.
- Push the magnet in faster. The flick is bigger.
With a single wire between the poles of a U-shaped magnet, moving the wire up or down across the field lines induces a p.d. Moving it along the lines, from one pole towards the other, induces nothing. The wire must cut across the field.
AQA GCSE says induced potential difference. Cambridge IGCSE and the Punjab Class 10 book say induced e.m.f. (electromotive force). At this level they mean the same thing.
Worked example 1: predicting the meter
A student pushes the N pole of a magnet into a coil at a steady speed. The needle of a centre-zero meter flicks 2 divisions to the right. Predict what happens when the student (a) holds the magnet still inside the coil, (b) pulls the N pole out at the same speed and (c) pushes the S pole in at twice the speed.
(a) The field through the coil is not changing, so no p.d. is induced. The needle reads zero.
(b) The change is reversed, so the induced p.d. is reversed. The needle flicks about 2 divisions to the left.
(c) Reversing the pole reverses the direction, so the needle flicks to the left. Doubling the speed makes the field change twice as fast, so the induced p.d. and current are about twice as big. The needle flicks about 4 divisions to the left, for about half as long.
What affects the size of the induced p.d.?
The induced p.d. is bigger when:
- The movement is faster, so the field through the coil changes more quickly.
- The magnetic field is stronger, for example with a stronger magnet.
- The coil has more turns. Each turn adds its own small p.d., in series with the others.
In a generator, a bigger coil area also helps. Faster movement and a stronger field both make the field through the coil change faster. A huge magnet held still induces nothing.
What decides the direction of the induced current?
Reversing the movement or swapping the poles reverses the induced p.d. There is also a deeper rule. The induced current always sets up a magnetic field that acts against the change that produced it. This rule is called Lenz's law.
Push the N pole of a magnet into a coil, and the induced current makes the near end of the coil an N pole. The two N poles repel, so the coil pushes back. Pull the magnet out, and the near end becomes an S pole, which attracts the magnet and again resists the movement.
This follows from conservation of energy. If the induced current helped the magnet along, you would get electrical energy for nothing. Instead, you do work against the opposing force, and that work becomes electrical energy.
Worked example 2: why is the magnet harder to push?
A student pushes a strong magnet into a coil twice. The first time, the ends of the coil are not connected. The second time, they are joined through a lamp. Explain why the magnet is harder to push the second time.
Answer: Both times, the changing field induces a p.d. in the coil. With the ends not connected, no current can flow, so the coil does not become a magnet. With the lamp connected, a current flows and turns the coil into an electromagnet whose near end repels the incoming magnet. The student must push harder, and this extra work is transferred to the lamp, which lights.
Some courses also use Fleming's right-hand rule. Hold the thumb and first two fingers of your right hand at right angles: thumb along the motion, first finger along the field (N to S), second finger along the induced current.
How does an a.c. generator work?
An a.c. generator, or alternator, has a coil that rotates in a magnetic field. In large power stations, an electromagnet usually rotates inside fixed coils instead, but the idea is the same.
As the coil turns, each side moves up through the field, then down. So the induced p.d. keeps reversing. The coil connects to the outside circuit through two slip rings, which turn with it, pressed against fixed carbon brushes.
A graph of the output p.d. against time is a smooth wave that swings from positive to negative:
- The p.d. is largest when the plane of the coil is parallel to the field lines. Its sides are then cutting straight across the lines, as fast as they can.
- The p.d. is zero when the plane of the coil is at right angles to the field lines. Its sides are then moving along the lines for an instant, cutting none.
One complete turn of the coil gives one complete cycle of the wave.
Worked example 3: generator speed
A simple generator coil turns 50 times every second. (a) Find the frequency and the period of the output. (b) The coil is now turned twice as fast. Describe how the graph changes.
Given: 50 turns per second, one cycle per turn
(a) Frequency: f = 50 Hz
Equation:
Substitution:
Answer: T = 0.020 s
(b) The coil now turns 100 times a second, so f = 100 Hz and T = 0.010 s. The peaks are twice as close together on the graph. The coil also cuts the field lines twice as fast, so each peak is twice as tall.
This is why many power-station generators in Pakistan, India and the UK turn at 3000 revolutions per minute: 50 turns a second gives 50 Hz mains. In the US, with 60 Hz mains, the same kind of generator turns at 3600 revolutions per minute.
How is a dynamo different?
A dynamo gives direct current. Its rotating coil connects to the circuit through a split-ring commutator instead of slip rings. Every half turn, just as the induced p.d. would reverse, the commutator swaps the connections, so the output never changes direction. On a graph, it looks like a row of humps, all on the same side of the time axis, dropping to zero twice in every turn.
How does a microphone use induction?
In a moving-coil microphone, a thin diaphragm is attached to a small coil that sits around a permanent magnet. The pressure changes of a sound wave push the diaphragm in and out, so the coil moves through the magnetic field and an alternating p.d. is induced. Its pattern matches the pattern of the sound wave. A loudspeaker is built the same way but works in reverse, using the motor effect.
Induction also makes transformers work: a changing current in one coil induces a p.d. in a second coil. You can explore induction in the electromagnetic induction simulation, and see where it leads in the transformers and National Grid simulation.
Common mistakes
- Saying a still magnet inside a coil induces a current. Only a change in the field does.
- Saying induction needs a complete circuit. The p.d. is induced either way. Only the current needs a complete circuit.
- Mixing up the generator effect and the motor effect. Generator: movement in a field gives a p.d. Motor: a current in a field gives movement.
- Putting the peak in the wrong place. The p.d. is largest when the plane of the coil is parallel to the field lines.
Key points
- Moving a wire across a magnetic field, or changing the field inside a coil, induces a p.d. With a complete circuit, a current flows.
- The induced p.d. is bigger with faster movement, a stronger field and more turns on the coil.
- The induced current's magnetic field opposes the change that caused it (Lenz's law), so work must be done.
- An a.c. generator uses slip rings and gives an alternating output. A dynamo uses a split-ring commutator and gives d.c.
- Microphones turn the pressure changes of sound into a matching alternating p.d.