Skip to content

Cambridge IGCSE Physics (0625) · Magnetism and electromagnetic effects

Electromagnetic induction

4.5.1

Core: an e.m.f. is induced in a conductor that cuts a magnetic field or sits in a changing field; a magnet and coil show it, and speed, magnet strength and number of turns set its size. Supplement: the induced e.m.f. always acts against the change behind it.

Loading simulation…

Symbols match your course. Open the full electromagnetic induction simulation for more presets and teacher tools.

What this topic covers

Turbines at Tarbela Dam in Pakistan, wind farms off Denmark and an electric guitar's pickup all make electricity by changing the magnetic field around a conductor. Syllabus 4.5.1 explains how; generators are on the a.c. generator page.

Two ways to induce an e.m.f. (Core)

  • Move a conductor across a field. A wire swung up through a U-shaped magnet's gap cuts the field lines. Slid along the lines, it induces nothing.
  • Change the field through a coil: move a magnet in or out, or switch on a nearby electromagnet.

The e.m.f. lasts only while something changes: a magnet resting inside a coil, however strong, induces nothing. In a complete circuit, the e.m.f. drives an induced current.

Demonstrating it (Core)

Join a coil of a few hundred turns to a sensitive centre-zero meter. With no cell in the circuit, any reading must come from induction.

  1. Push a magnet's N pole into the coil: the needle kicks to one side.
  2. Hold the magnet still: the needle settles back on zero.
  3. Withdraw the magnet: the needle flicks the opposite way.
  4. Push the S pole in: the needle moves as in step 3.

What sets the size (Core)

The induced e.m.f. grows with faster movement, a stronger magnet, and a coil of more turns. Faster motion and a stronger magnet speed up the change of field inside the coil; extra turns help because every turn adds its own share.

Worked example: predicting the needle (Core)

A steady push of an N pole into a coil swings the needle 4 divisions right. Predict the needle when the magnet is:

  • pulled out at the same speed: about 4 divisions left;
  • pushed in twice as fast: a bigger swing right, about 8 divisions, over half the time;
  • pushed in as before, with twice the turns on the coil: a bigger swing right.

Which way? (Supplement)

The induced e.m.f. always acts against the change producing it. As an N pole approaches, the coil's nearer end turns into an N pole and repels it; as the magnet leaves, that end turns into an S pole and holds it back. So moving the magnet takes work, which supplies the electrical energy. If induction helped the motion, energy would appear from nothing.

For a straight wire, the motion, the field and the induced current are each at 90° to the other two. The syllabus names no rule; the usual one is Fleming's right-hand rule. Hold your right hand with the thumb and first two fingers at right angles. Point the thumb the way the wire moves and the first finger the way the field points (N to S). Your second finger now gives the induced current.

Example: a wire is pulled up between an N pole on the left and an S pole on the right. Thumb up, first finger to the right: the second finger points into the page, the way the induced current flows.

Optional check: the field's push on the induced current must act against the motion, so here that push is downwards. Your left hand, with its thumb down and first finger to the right, also gives a current into the page. Keep the two hands apart: the right hand for an induced current, as in a generator, and the left hand for the force on a current from a supply, as in a motor.

Magnet, coil and meter on the stage

In the simulation above, the Magnet and coil set-up starts with the N pole facing a 200-turn coil, 16 cm from its middle, at a Push and pull speed of 0.2 m/s. The meter's range is ±10 mV.

  1. (Core) Press Push. The needle swings right, Induced e.m.f. goes positive and Biggest so far reaches about 4 mV. Once the magnet stops in the middle, it reads 0.
  2. (Core) Press Pull: the needle swings left, a negative reading. Now press Flip, which works only with the magnet well clear of the coil, then Push: the S pole also reads negative.
  3. (Core) Before each new push, press Pull, then Start the graph again. Change one setting at a time: speed 0.4 m/s, Magnet strength Strong, or Turns on the coil 400. Each roughly doubles Biggest so far. Put each back before the next.
  4. (Supplement) Watch Coil end facing the magnet: the same pole as the magnet's, "repels the magnet", on the way in; the other pole, "pulls on the magnet", on the way out.

The Faraday's law box goes beyond 0625.

Common mistakes

  • Thinking that a magnet resting inside a coil induces an e.m.f. because the field there is strong. Only a changing field induces one; a steady field, however strong, gives a reading of zero.
  • Saying that nothing is induced when the circuit is broken. The e.m.f. is still induced across the ends of the coil or wire; without a complete circuit there is simply no current.
  • Giving loose factors such as 'a bigger magnet' or 'a bigger coil'. The three to state are a faster movement, a stronger magnet (field) and more turns on the coil.
  • Expecting an e.m.f. when a wire slides along the field lines. The wire has to cut across the lines; moving parallel to them induces nothing.
  • (Supplement) Claiming that a coil attracts an N pole pushed towards it. The end facing the magnet turns into an N pole and repels it, because the induced e.m.f. acts against the change.
  • (Supplement) Using the left hand, with the thumb along the motion, to find an induced current. That gives the opposite direction. Use Fleming's right-hand rule instead: thumb the way the wire moves, first finger along the field, then read the induced current from the second finger.

Exam-style questions

Original questions written in the style of Cambridge IGCSE. Try each one before you reveal the answer.

  1. 1.A student in Accra connects a coil of insulated wire to a sensitive centre-zero meter. There is no cell in the circuit. When the N pole of a bar magnet is pushed into the coil, the needle moves to the right.

    1. (a)Explain why the needle moves even though the circuit contains no cell.

      2 marks
      Show the answer

      Answer: As the magnet moves, the magnetic field through the coil changes. This induces an e.m.f. in the coil, which drives a current through the meter.

      Marking points

      • the magnetic field through (linking) the coil changes / the coil cuts field lines
      • an e.m.f. is induced, which drives a current (through the meter)
    2. (b)The magnet is then left resting inside the coil. State the reading on the meter and explain your answer.

      2 marks
      Show the answer

      Answer: Zero. With the magnet at rest, the field inside the coil stays the same, so no e.m.f. is induced.

      Marking points

      • zero (no deflection)
      • the field inside the coil stays constant / no field lines are being cut
    3. (c)Describe what the needle does when the magnet is pulled back out of the coil.

      1 mark
      Show the answer

      Answer: It moves to the left, the opposite way, and then returns to zero.

      Marking points

      • moves to the left / the opposite way
    4. (d)State three changes, each of which would make the needle move further.

      3 marks
      Show the answer

      Answer: Move the magnet more quickly, use a stronger magnet, and use a coil with more turns.

      Marking points

      • move the magnet faster
      • stronger magnet
      • more turns on the coil
  2. 2.A teacher in Hanoi connects a long copper wire to a sensitive meter. A straight part of the wire passes horizontally through the gap of a horseshoe magnet. In the gap, the field lines run horizontally from one pole to the other, crossing the wire at 90°.

    1. (a)Describe how the wire and meter can be used to demonstrate an induced e.m.f. Include what the class sees.

      3 marks
      Show the answer

      Answer: Move the wire up (or down) through the gap. The meter needle moves while the wire is moving. When the wire stops the reading is zero, and moving it the other way makes the needle move the other way.

      Marking points

      • move the wire up or down through the gap (across the field)
      • the meter deflects while the wire is moving
      • no reading when the wire is still / opposite deflection when moved the opposite way
    2. (b)The teacher now moves the wire horizontally, along the field lines. State and explain what the meter shows.

      2 marks
      Show the answer

      Answer: Zero, because the wire is moving along the field lines and is not cutting across any of them.

      Marking points

      • zero / no deflection
      • the wire is not cutting (crossing) the field lines
    3. (c)Suggest why a sensitive meter is needed for this experiment.

      1 mark
      Show the answer

      Answer: The induced e.m.f. and current from a single wire are very small.

      Marking points

      • the induced e.m.f. / current is very small
  3. 3.(Supplement) The N pole of a bar magnet is moved towards end X of a coil. The coil is connected to a resistor, so a current flows while the magnet moves.

    1. (a)State the magnetic pole formed at end X while the magnet approaches.

      1 mark
      Show the answer

      Answer: An N pole.

      Marking points

      • N (north) pole
    2. (b)Explain why this pole is formed at X.

      2 marks
      Show the answer

      Answer: The induced e.m.f. acts against the change that causes it. An N pole at X repels the approaching N pole, so it opposes the magnet's movement towards the coil.

      Marking points

      • the induced e.m.f. / current acts against the change that produces it
      • an N pole at X repels the approaching N pole (opposes the motion)
    3. (c)The magnet is then moved away from X. State the pole formed at X now.

      1 mark
      Show the answer

      Answer: An S pole, which attracts the departing N pole.

      Marking points

      • S (south) pole
    4. (d)Explain why a force is needed to keep the magnet moving towards the coil, and state where the electrical energy in the resistor comes from.

      2 marks
      Show the answer

      Answer: The coil repels the magnet, so work must be done against this repulsion to keep it moving. The energy from that work is transferred electrically to the resistor, which warms up.

      Marking points

      • the coil repels the magnet, so work must be done against it
      • the energy comes from the work done (by whoever moves the magnet) against the repulsion
  4. 4.(Supplement) A horizontal wire runs into the page, in a magnetic field. The N pole is on the left of the wire and the S pole on its right. The wire is part of a complete circuit and is moved straight downwards through the field.

    1. (a)State which way the field pushes on the induced current in the wire.

      1 mark
      Show the answer

      Answer: Upwards, opposing the downward motion.

      Marking points

      • upwards / opposite to the motion
    2. (b)Determine the direction of the induced current in the wire.

      1 mark
      Show the answer

      Answer: Out of the page, towards the reader. By Fleming's right-hand rule: thumb down for the motion and first finger to the right for the field, so the second finger points out of the page.

      Marking points

      • out of the page (towards the reader)
    3. (c)The wire is then moved upwards at the same speed. State how the induced current changes.

      1 mark
      Show the answer

      Answer: It reverses, flowing into the page, with the same size.

      Marking points

      • reverses / now into the page
    4. (d)State how the directions of the motion, the field and the induced current are related.

      1 mark
      Show the answer

      Answer: Any two of them are perpendicular to each other.

      Marking points

      • mutually perpendicular (each at 90° to the others)

Quick check

6 questions

  1. 1.A student pushes a magnet into a coil and then leaves it resting inside. What does a meter joined to the coil show once the magnet has stopped?
  2. 2.Which change does not make the induced e.m.f. larger when a magnet is pushed into a coil?
  3. 3.A straight wire in a circuit runs into the page, between an N pole on the left and an S pole on the right. When is no e.m.f. induced in it?
  4. 4.Pulling the N pole of a magnet out of a coil makes the meter needle move left. The S pole is then pushed into the same end of the coil. Which way does the needle move?
  5. 5.(Supplement) The N pole of a magnet is pushed towards a coil in a complete circuit. What pole forms at the end of the coil nearest the magnet?
  6. 6.(Supplement) Why must an induced current always act against the change that causes it?