What this topic covers
Hydroelectric turbines on the Zambezi, a car's alternator in Mexico City and the hub dynamo on a Dutch bicycle all turn motion into alternating current. Section 4.5.2 explains how; induction itself is on the Electromagnetic induction page.
A coil spinning in a field (Supplement)
- A rectangular coil of many turns spins on an axle in the gap between a magnet's poles, driven by a turbine, engine or hand crank.
- Each end of the coil is attached to its own slip ring, a complete metal ring on the axle that turns with the coil.
- A fixed carbon brush presses on each ring, so each end of the coil always feeds the same wire of the circuit, and nothing twists.
Each long side moves up through the field for half a turn, then down for the next, so its e.m.f. reverses every half turn. The slip rings pass this straight to the circuit: the output is alternating.
A magnet spinning beside a coil (Supplement)
Or swap the roles: spin a magnet inside a fixed coil. As the poles sweep past, the field through the coil keeps reversing, inducing an alternating e.m.f. The coil never moves, so no slip rings are needed. A bicycle hub dynamo works this way: a ring of magnets turns around a fixed coil, so it gives a.c. Its name can mislead, because in physics a "dynamo" usually means a generator with a split ring, which gives d.c.
Coil position and the e.m.f. (Supplement)
Start with the coil's plane at right angles to the field, upright when the field is horizontal.
| Turned through | Coil's plane | e.m.f. |
|---|---|---|
| 0 | At right angles to the field | Zero |
| ¼ turn | Parallel to the field | Peak |
| ½ turn | At right angles again | Zero |
| ¾ turn | Parallel again | Trough |
| 1 turn | Back where it began | Zero |
At the zeros the sides glide along the field lines; at a peak or trough they cut straight across them, in opposite directions for the two. One turn gives one complete cycle.
The trap: the e.m.f. is zero just when the most field passes through the coil, because what counts is how fast the sides cut the lines.
Changing the graph (Supplement)
- Turn faster: taller peaks and more cycles each second (a higher frequency).
- More turns, or a stronger magnet: the peaks grow, but the cycles per second stay the same.
Worked example: reading the graph (Supplement)
A generator's e.m.f. starts at zero, rises to +6.0 V at 0.010 s, is zero at 0.020 s, reaches −6.0 V at 0.030 s and is zero again at 0.040 s. At the start, the coil's plane is at right angles to the field.
- Where is the coil at 0.010 s and 0.030 s? Its plane is parallel to the field: the peak and the trough.
- And at 0.020 s? Half a turn on, at right angles to the field again, so the e.m.f. is zero.
- How fast is it turning? One cycle takes 0.040 s, so it makes 1 ÷ 0.040 = 25 turns each second: 25 Hz.
- Sketch it at twice the speed: peaks of about +12 V and −12 V, each cycle lasting 0.020 s.
Generating on screen
In the simulation above, press Generator in the Experiment group. It begins with Slip rings (a.c.), a Turning speed of 1 rev/s and a 200-turn coil. The meter is connected across the two brushes, and a lamp is in the circuit from the start.
- Press Play. Coil's plane begins at "At right angles to the field", with an Output e.m.f. of 0; a quarter turn later the trace reaches its first peak.
- Set the speed to ¼× and watch the little coil icons drawn above the trace: upright ones sit on the zeros, flat ones on the peaks and troughs.
- Tap Faster four times, so the coil makes 2 rev/s. The peaks double and twice as many cycles fit on the trace: Peak output was 0.754 V and is now 1.51 V.
- Tap Slower four times to return to 1 rev/s. Then raise Turns on the coil or pick a stronger Field between the magnets, one at a time: taller peaks, same frequency.
The Split ring (d.c.) option, which makes a dynamo, and the NBAω formula behind Peak output go beyond 0625.