Higher tier, physics only: spec point 4.7.3.2
As with all of 4.7.3, this is GCSE Physics only, tested on Higher tier papers. Be ready to explain why an alternator's output alternates while a dynamo's flows one way, and to sketch and read p.d.–time graphs for both.
There is no equation of its own, though graph questions may need (4.6.1.2, on the equation sheet). The specification names both machines but not their rings; the explanations need them, so learn both.
One spinning coil
Both machines rotate a coil between two magnetic poles. Its long sides sweep through the field, so a p.d. is induced in the coil. How big it is depends on how quickly the sides are cutting field lines, which varies through each turn:
| Coil's plane | Long sides are moving | p.d. in the coil |
|---|---|---|
| Perpendicular to the field | along the field lines, cutting none | zero |
| Parallel to the field | straight across the field lines | at its peak |
| Half a turn on | the opposite way through the field | reversed |
Inside the coil, then, the p.d. always swaps direction every half turn. The two machines differ only in how the coil connects to the circuit outside.
Alternator: slip rings give a.c.
Each end of the coil has its own complete slip ring, turning with it, and a carbon brush rests on each ring. One end always feeds the same brush, so every reversal reaches the circuit: alternating current. On a p.d.–time graph this makes a smooth wave, up to a positive peak, down through zero to a negative peak and back, one cycle per turn.
Dynamo: a split ring gives d.c.
A dynamo replaces the slip rings with a split-ring commutator, two half-rings on the axle. They change brushes every half turn, exactly when the coil's p.d. is zero. Each reversal inside the coil is cancelled by a swap of connections, so the output keeps one sign: direct current. The graph is a string of humps, all above the axis, two for each turn.
Changing the graph
- Spin the coil faster and the peaks grow taller and crowd closer together: the frequency goes up.
- Use a stronger magnet or add turns and only the height changes; the spacing does not change.
Worked example: reading an alternator trace
An alternator's p.d.–time graph peaks at 6.0 V. One complete cycle, from zero through both peaks and back to zero, lasts 0.040 s. Find the frequency, and the coil's rate of turning.
Given: period s. Equation: . Substitution: . Answer: Hz. One cycle comes from each turn, so the coil makes 25 turns per second.
Two predictions follow. With a split ring at the same speed, the peak stays at 6.0 V, nothing falls below zero, and a fresh hump starts every 0.020 s. With slip rings at twice the speed, the peak doubles to 12 V and the frequency becomes 50 Hz.
The generator on screen
In the simulation above, switch Experiment to Generator and press Play. The defaults are 200 turns, a 0.2 T field, slip rings and 1 revolution per second. The meter reads the p.d. between the two brushes, and a lamp is part of the circuit from the outset.
- Watch Output p.d. rise to about +0.75 V, fall to about −0.75 V and repeat, while Kind of output shows a.c., 1.00 Hz. The Coil’s plane card tracks the coil: close to 90° from upright (Parallel to the field) near each peak, and close to 0° (At right angles to the field) each time the output passes zero.
- Tap the Slip rings button next to the stage and it switches to a split ring. Now the trace never dips below zero, and Kind of output reads d.c., 2.00 pulses a second.
- Tap Faster 4 times to reach 2 rev/s. Peak output doubles from 0.754 V to 1.51 V, and Kind of output now counts 4.00 pulses a second. The Peak output formula is beyond GCSE; just compare values.
- Press Start the graph again after each change to compare the Induced p.d. against time traces.