Refraction in the AQA specification
Refraction is spec point 4.6.2.2. At AQA GCSE it is qualitative: you draw and explain what happens to a ray, but you do not calculate angles.
- Both tiers: draw ray diagrams of light entering and leaving a material, such as a glass block.
- Higher tier only: explain refraction with wavefront diagrams and the change in wave speed, and know that one material can behave differently towards different wavelengths.
- GCSE Physics only: Required practical activity 9, on the reflection and refraction of light.
There is no refraction equation to learn for AQA. Snell's law, refractive index, critical angle and total internal reflection are not in the AQA GCSE specification.
What refraction looks like
Light that crosses a boundary between two materials at an angle changes direction. That is refraction. It makes a pencil in a glass of water look bent at the surface, and a pool look less deep than it is.
Drawing a refraction ray diagram
- Draw the boundary between the two materials.
- Where the ray meets the boundary, draw the normal: a dashed line at 90° to the surface.
- Draw the incoming ray with an arrow. The angle of incidence is between this ray and the normal.
- Draw the ray inside the new material. The angle of refraction is between this ray and the normal.
The bending follows three rules:
- Air into glass, water or Perspex: the ray bends towards the normal, so the angle of refraction is smaller.
- Glass, water or Perspex into air: the ray bends away from the normal.
- A ray arriving along the normal is not bent at all.
With a rectangular block, the emerging ray runs parallel to the incoming ray but is displaced to one side.
Worked example: getting the angles right
A ray box sends a ray at a glass block. A student measures the angle between the ray and the surface of the block as 55°. Inside the glass, the refracted ray makes 22° with the normal. What is the angle of incidence, and which way has the ray bent?
Given: angle between ray and surface = 55°, angle of refraction = 22°
Equation: angle of incidence = 90° − angle to the surface, because the normal is at 90° to the surface
Substitution: angle of incidence = 90° − 55°
Answer: angle of incidence = 35°. The angle of refraction, 22°, is smaller, so the ray has bent towards the normal, as expected for light entering glass.
Higher tier: why the ray bends
Light travels more slowly in glass than in air. Picture wavefronts, the lines joining the crests of a wave, arriving at an angle. One end of each wavefront reaches the glass first and is slowed while the other end is still in air. The wavefront pivots, so the wave heads off in a new direction. Inside the glass the wavefronts are closer together, because the wavelength is shorter while the frequency stays the same.
Water waves in a ripple tank do the same when they cross into shallower, slower water at an angle.
A material can treat different wavelengths very differently. Microwaves pass through glass but are absorbed by the water in food. Even the colours of visible light refract by slightly different amounts in glass, which is why a prism spreads white light into a spectrum.
Required practical activity 9 (physics only)
Place a glass or Perspex block on paper and draw round it. Aim a thin beam from a ray box into the block and mark the ray's path with small crosses. Remove the block, join the crosses, draw the normals, and measure the angles with a protractor. Repeat with other substances, keeping the angle of incidence the same. The practical also asks you to compare how different surfaces, such as a mirror and a matt sheet, reflect light. You can rehearse the refraction steps in the virtual practical; its refractive index section goes beyond AQA.
Using the simulation
In the simulation above, the light starts in Air and goes into Glass (or choose the Air → glass quick set-up). Move the angle of incidence and watch the ray bend towards the normal. Now choose Glass → air, or press the swap button (⇅) between the two menus. Keep the angle below 40°, and the ray now bends away from the normal. Set the angle to 0° and the ray passes straight through. You can ignore the Snell check and critical angle readouts, since AQA does not test them.