What AQA asks for: spec point 4.6.2.2
- Both tiers, GCSE Physics and Combined Science: Required practical 10, on how the finish of a surface affects the infrared it gives out or takes in. Combined Science has it too, under its own number. There is no equation.
- Higher tier only: one material can respond to different wavelengths in quite different ways.
- GCSE Physics only: the rule that good absorbers are good emitters, and perfect black bodies (4.6.3), are on the black body radiation page.
Refraction is also part of 4.6.2.2 and has its own page. Thermal conductivity and insulation belong to 4.1.2.1 instead.
Infrared is an electromagnetic wave
Infrared lies between microwaves and visible light in the electromagnetic spectrum. Its wavelengths are longer than red light’s, so it is invisible, though skin feels it as warmth.
Like all electromagnetic waves, it is transverse, needs no medium and moves at the speed of light in a vacuum. That is how the Sun's infrared reaches us across space. It carries energy from emitter to absorber, raising the absorber's internal energy. Every object emits some infrared; warmer ones emit more each second.
What a surface does with infrared
Arriving infrared can be absorbed, reflected or transmitted (passed through). The material and its surface finish decide the shares.
| Surface | As an emitter | As an absorber |
|---|---|---|
| Matt black | best | best |
| Shiny black | good | good |
| Shiny silver (polished metal) | worst | worst: reflects most of it |
Matt white paint looks pale because it reflects visible light, yet it emits and absorbs the infrared from warm objects almost as well as matt black. Higher tier: that is one surface behaving differently at different wavelengths. Window glass is another: it lets light through but absorbs most of the infrared from a warm room.
Learn the extremes: matt black emits and absorbs best, shiny silver worst. Marathon runners in London get shiny foil blankets, which emit little infrared; solar water heaters use matt black panels.
Required practical 10: the Leslie cube
A Leslie cube is a hollow metal box with a different finish on each side: matt black, matt white, shiny black and shiny silver.
- Stand the cube on a heatproof mat, fill it with water just off the boil and put the lid on.
- Set an infrared detector 10 cm from one face, measured with a ruler.
- Record the reading once it settles.
- Turn the cube to each other face, keep the distance at 10 cm and record again.
- Repeat, and find a mean for each face.
Independent variable: the type of surface. Dependent variable: the detector reading. Control variables: the distance, the water temperature and the detector. The water cools, so work quickly.
To compare absorbers, wax a drawing pin to the back of a matt black plate and a shiny silver plate, stand them equal distances either side of a radiant heater, and time each pin’s fall.
Worked example: comparing detector readings
Detector readings in W/m², 10 cm from each face:
| Face | 1st | 2nd | 3rd | Mean |
|---|---|---|---|---|
| Matt black | 84 | 82 | 83 | 83 |
| Matt white | 80 | 78 | 61 | 79 |
| Shiny black | 77 | 75 | 76 | 76 |
| Shiny silver | 5 | 4 | 4 | 4.3 |
Anomaly: 61 is far below the other matt white readings; perhaps the detector was knocked back. Leave it out: W/m².
Ranking: matt black, then matt white, then shiny black. Shiny silver is far behind: , so matt black emits about 19 times as much.
Conclusion: for the same colour, matt beats shiny (83 against 76).
Improvement: record the water temperature with each reading, and vary the order of the faces between repeats.
In the simulation above
- Press Radiation in the row of buttons above Play. Test is already on Emitting, with Matt black facing the detector 10 cm away. The Detector card shows about 105 W/m².
- Before pressing Play, alternate Record and Turn until the Results table holds all four faces: about 105, 100, 97 and 5.5 W/m² for matt black, matt white, shiny black and shiny silver.
- Press Play (the clock runs 20 times faster than real time). The Water temperature falls slowly, and the Detector reading drifts down with it.
- Press Reset, pick Matt black under Face pointing at the detector and set Detector distance to 20 cm. The reading falls to about 32 W/m², so distance must be controlled.