Scalars and Vectors Explained: Examples, Directions and Adding Vectors
Learn what makes a quantity a scalar or a vector, see common examples side by side, use plus and minus signs for direction, and add vectors along a line or at right angles.
Published · 7 min read
On this page
A scalar quantity has a size only. A vector quantity has a size and a direction. That is the whole difference.
Distance is a scalar: "5 km" is a complete answer. Displacement is a vector: you have to say "5 km north" or "5 km towards the station". In the same way, speed is a scalar and velocity is a vector. Mass is a scalar, but weight is a vector, because weight is a force and every force acts in some direction.
The size of a quantity, with its unit, is called its magnitude. So a vector has a magnitude and a direction, while a scalar has a magnitude only. This guide gives a table of examples, shows how to handle direction with plus and minus signs, and explains how to add vectors.
How can you tell a scalar from a vector?
Ask one question: does it make sense to say which way the quantity points?
- A bag of rice has a mass of 5 kg. The mass does not point anywhere, so it is a scalar.
- The Earth pulls that bag down with a force of 49 N. The force points down, so it is a vector.
- A one-day cricket match lasts about 7 hours. Time has no direction, so it is a scalar.
- A bullet train in Japan travels at 80 m/s towards Osaka. That is a velocity, a vector. Its speed, 80 m/s with no direction, is a scalar.
Which quantities are scalars and which are vectors?
| Scalar (size only) | Vector (size and direction) |
|---|---|
| Distance, in m | Displacement, in m |
| Speed, in m/s | Velocity, in m/s |
| Mass, in kg | Weight, in N |
| Energy, in J | Force, in N |
| Time, in s | Acceleration, in m/s² |
| Temperature, in °C | Momentum, in kg m/s |
The first three rows are matching pairs. Distance and displacement share a unit, and so do speed and velocity, so the unit alone will not tell you which is which. Mass and weight have different units, because weight is a force.
Two shortcuts help. Every kind of force is a vector: weight, friction, tension, drag and thrust. Every kind of energy is a scalar, and so are work done and power.
Why does direction matter?
Imagine two forces of 10 N acting on a box. If both push to the right, together they act like one 20 N force. If they push in opposite directions, they cancel and the total is zero. The sizes are the same in both cases, but the results are completely different. That is why you cannot add vectors by adding their sizes.
Using signs along a line
When everything happens along one straight line, signs do the job of directions. Pick one direction to be positive. The opposite direction is then negative.
For example, take right as positive. A trolley moving right at 4 m/s has a velocity of +4 m/s. A trolley moving left at 4 m/s has a velocity of −4 m/s. Both have a speed of 4 m/s, because speed has no direction and is never negative.
Worked example 1: a walk with a return leg
A student in Accra walks 300 m east from home to a shop. Then the student walks 120 m west to a friend's house. The whole walk takes 6.0 minutes. Find the distance, the displacement, the average speed and the average velocity.
Given: east is positive, so the two legs are +300 m and −120 m. Time t = 6.0 min = 360 s.
Distance: 300 + 120 = 420 m
Displacement: 300 + (−120) = +180 m, so 180 m east of home
Average speed: , so 1.2 m/s (2 significant figures)
Average velocity: east
Answer: distance 420 m, displacement 180 m east, average speed 1.2 m/s, average velocity 0.50 m/s east
If the student then walks back home, the displacement for the whole trip becomes zero, and so does the average velocity, even though the distance has grown to 600 m. A runner who finishes one lap of a 400 m track is in the same position: 400 m of distance, zero displacement.
To compare the length of a route with the straight line from start to finish, see the distance and displacement simulation.
How do you draw a vector?
A vector is drawn as an arrow.
- The arrow's length, drawn to a chosen scale, shows the magnitude.
- The arrow points the same way as the quantity.
- The arrowhead goes at the end, and a label gives the value.
You can give the direction as a compass point, such as north-east. You can give an angle from a reference line, such as "30° above the horizontal". Or you can use a three-figure bearing, measured clockwise from north, such as 060°.
For example, with a scale of 1 cm to 2 m/s, a velocity of 7 m/s north-east is an arrow 3.5 cm long, pointing halfway between north and east.
How do you add vectors?
Vectors along the same line
Add them with their signs. A plane flying east at 230 m/s with a 20 m/s tail wind moves over the ground at 230 + 20 = 250 m/s east. Into a 20 m/s head wind, it moves at 230 − 20 = 210 m/s east.
Vectors at right angles
Draw the vectors head to tail, so the second arrow begins where the first one finishes. The resultant is the single arrow that joins your starting point to your finishing point. The order does not matter. North then east gives the same resultant as east then north.
With two vectors at 90°, the drawing is a right-angled triangle and the resultant is its longest side. Find its length with Pythagoras and its angle with . Some courses ask only for a scale drawing. Others want the calculation as well.
Worked example 2: a delivery rider
A delivery rider in Karachi rides 2.4 km due north, then 1.0 km due east. Find the distance travelled and the displacement.
Given: 2.4 km north, then 1.0 km east, at right angles
Distance: 2.4 + 1.0 = 3.4 km
Equation: displacement
Substitution:
Size: 2.6 km
Direction: , so east of north (2 significant figures)
Answer: the rider has travelled 3.4 km, but the displacement is 2.6 km at 23° east of north, a bearing of 023°.
Worked example 3: a boat crossing a river
A small boat in Bangladesh heads straight across a river at 3.2 m/s. The current carries it downstream at 1.8 m/s. Find the boat's resultant velocity.
Equation:
Substitution:
Size: 3.7 m/s (2 significant figures)
Direction: , so downstream from the straight-across line
Answer: 3.7 m/s at 29° downstream from straight across
Vectors at other angles need a scale drawing, or the reverse process: splitting each vector into two parts at right angles. You can try both in the vector addition and resolution simulation.
Common mistakes
- Thinking any negative number is a vector. Temperatures and energy changes can be negative too.
- Leaving the direction out of a vector answer. "2.6 km" is a distance. "2.6 km at 23° east of north" is a displacement.
- Adding vectors at right angles like ordinary numbers. 2.4 km + 1.0 km gives the distance, not the displacement.
- Assuming distance and displacement are equal. They match only for a straight-line trip in one direction.
- Giving a negative speed. Speed is never negative. Velocity can be.
- Calling weight a scalar. Weight is a force, so it always has a direction.
- Measuring an angle from the wrong line. Say clearly what the angle is measured from.
Key points
- A scalar has magnitude only. A vector has magnitude and direction.
- Scalars include distance, speed, mass, energy, time and temperature.
- Vectors include displacement, velocity, weight and every other force, acceleration and momentum.
- In one dimension, a plus or minus sign shows which way a vector points.
- A vector is drawn as an arrow whose length shows its size, to scale.
- To add vectors at right angles, draw them head to tail, then use Pythagoras for the size and for the direction.