Skip to content

Waves and sound simulation

Transverse and Longitudinal Waves Simulation

Send transverse or longitudinal waves along a slinky, follow one particle as it vibrates in place, and measure the wavelength with a ruler and the period with a stopwatch. Live displacement–distance and displacement–time graphs show how the two differ.

Loading simulation…
Show symbols for

Predict first

Question 1 of 4

Waves travel along a slinky at 2.0 m/s. With the source vibrating at 1.0 Hz, neighbouring crests are 2.0 m apart. The source now vibrates at 2.0 Hz, on the same slinky. How far apart are neighbouring crests now?

Try this

  1. 1Press Play and watch the diamond marker ride a crest along the slinky, while the highlighted particle 1.0 m from the source only moves up and down. Pause and check that it is still above the 1.0 m mark on the ruler.
  2. 2Press Ruler and drag markers A and B onto two neighbouring crests. Compare your reading with the Wavelength readout, 2.00 m at the starting settings, and with the λ arrow on the displacement–distance graph.
  3. 3Press Count, let several crests pass the tracked particle, then press Count again. Divide the time by the number of waves to find the period, then work out the frequency from f = 1/T.
  4. 4Raise the Frequency from 1.0 Hz to 2.0 Hz and leave the Wave speed at 2.0 m/s. Predict the new wavelength, then watch the shorter waves travel out behind the longer ones.
  5. 5Choose Longitudinal under Type of wave. Find a compression (C) on the stage and the point on the displacement–distance graph where the line crosses zero going down.

A slinky you can slow down

The stage shows the first four metres of a very long slinky, with a bead on every coil standing in for one particle of the medium. A source at the left-hand end starts to vibrate when you press Play. The rest of the slinky does not move at once: the disturbance spreads out from the source at the wave speed, and each bead stirs only when that front arrives. The slinky carries on past the edge of the stage, so no reflected wave ever comes back to muddle the picture.

Watching one particle

The highlighted particle is the most important thing on the stage. In transverse mode it moves straight up and down across the slinky, while crests sweep past it to the right. Its fading trail draws a short vertical line, never a path along the chain. Switch to longitudinal mode and it slides back and forth along the slinky instead, but always about the same mark on the ruler, and after each complete cycle it is exactly where it began. Energy reaches every bead down the line, yet no bead makes that trip. The diamond marker rides a single crest, or a single compression, from one end of the stage to the other, so you can see what really does travel.

Measuring λ, T and f

Press Ruler to bring up markers A and B. Line them up with neighbouring crests, or neighbouring compressions, and the gap between them is one wavelength. Spanning several wavelengths and dividing gives a more precise value, exactly as it would with a real slinky and a metre rule.

For the period, press Count. Timing begins as the next crest reaches the tracked particle; press Count again and it ends when a later crest arrives, so it always covers a whole number of waves. Time divided by waves gives the period, and waves divided by time gives the frequency. Multiply your frequency by your wavelength and compare the result with the speed set on the slider. With careful measurements, v=fλv = f\lambda agrees to within a few per cent.

Two graphs that look alike

The displacement–distance graph is a snapshot: every particle is plotted at its rest position against how far it is displaced at that instant. Crest to crest along its horizontal axis is a distance, the wavelength. The displacement–time graph follows only the tracked particle, and crest to crest on it is a time, the period TT. Both are sine curves, so read the axis labels before anything else.

In longitudinal mode the displacement points along the slinky, yet the graphs still plot it upwards, with positive meaning away from the source. A compression sits where the snapshot crosses zero heading downwards: beads just behind it have been pushed forward and beads just ahead have been pushed back, so they bunch up. A rarefaction sits where the line crosses zero heading upwards.

What sets each quantity

The source decides the frequency. The slinky decides the speed, which for a real one depends on how firmly it is stretched. The wavelength is then whatever fits, λ=v/f\lambda = v/f, so doubling the frequency packs the crests twice as closely. Changing the amplitude alters neither the speed nor the wavelength, only the energy carried. A new speed counts as a new slinky, so the wave starts again from rest.

Equations

Check your understanding

8 questions

  1. 1.A wave on a rope has a frequency of 4.0 Hz and a wavelength of 0.75 m. What is its speed?
  2. 2.Which statement describes a longitudinal wave?
  3. 3.On a displacement–time graph for one point on a wave, neighbouring crests are 0.40 s apart. What is the frequency of the wave?
  4. 4.On a displacement–distance graph of a wave, what does the distance from one crest to the next show?
  5. 5.Sound travels through air at 340 m/s. Find the wavelength of a note with a frequency of 170 Hz.
  6. 6.A slinky is shaken with twice the amplitude but the same frequency. What happens to the speed of the waves along it?
  7. 7.In a longitudinal wave, where are the particles closest together?
  8. 8.A floating ball bobs up and down as ripples pass it on a pond. What does this show?

For teachers

Embed it in your site or open it full-screen for the projector.

Read more