Barriers, shallows and gaps
Sea waves heading for a harbour are turned back by the sea wall, slowed and swung round over a sandbank, and fanned out by the gap between breakwaters. A ripple tank recreates all three on a bench.
Reflection (Core)
A straight metal strip slanted across the wavefronts sends the ripples off in a new direction. Measured from the normal, at 90° to the strip, angle of incidence = angle of reflection (stated for light in 3.2.1, Core). The depth is unchanged, so speed, frequency and wavelength are too.
Refraction (Core)
A glass plate on the tank floor makes the water over it shallower, and ripples move more slowly there.
- Frequency stays the same: the bar sets it, and every crest reaching the plate carries on across.
- Wavelength shrinks in proportion to the speed, since : the bright lines crowd together.
- Direction: wavefronts that meet the plate's edge at a slant pivot, because the end arriving first slows first. The ripples' direction of travel turns towards the normal.
Ripples arriving along the normal slow and shorten but carry straight on.
Worked example 1 (Core)
A bar vibrates at 15 Hz and its wavefronts are 1.6 cm apart in deep water. Over the plate the ripples travel at 0.15 m/s. Find their deep-water speed and their wavelength over the plate.
Over the plate, is still 15 Hz:
Answer: 0.24 m/s, then 1.0 cm.
Diffraction (Core)
Beyond a gap in a barrier, plane wavefronts curve and spread into water that a straight-line path would miss. Ripples sliding past the end of a single barrier also curl round behind it. Both are diffraction. Speed, frequency and wavelength are unchanged; only the wavefronts' shape and direction change.
How much spreading? (Supplement)
- Gap about one wavelength wide, or narrower: the strongest spreading, with almost semicircular fronts. A gap far narrower than λ lets less energy through, so those ripples are weaker.
- Gap of many wavelengths: the wave passes on mostly as a straight-sided beam, curving only at its ends.
- The ratio counts. A narrower gap or a longer wavelength (lower frequency) both increase the spreading.
- At an edge: longer wavelengths bend further round behind the barrier.
Worked example 2 (Supplement)
Ripples of frequency 8.0 Hz travel at 0.24 m/s. Gaps of 3.0 cm, 9.0 cm and 24 cm are available. Which spreads the ripples most?
Gap ÷ wavelength: 1.0, 3.0 and 8.0. Answer: the 3.0 cm gap, matching the wavelength. At 4.0 Hz, λ doubles to 6.0 cm and the 9.0 cm gap spreads them far more.
Simulation tasks
In the simulation above, the tank opens in Measure with calm water. Switch set-up with the menu beside Play.
- (Core) Choose Reflection and press Play. With Rays, normals and labels already on, the Angle of reflection (r) card matches the Angle of incidence (i) card at 40°. Drag Angle of incidence to 60° and both follow.
- (Core) Choose Refraction. Both columns of the table keep 5.0 Hz, while deep water's 0.25 m/s and 5.00 cm become 0.15 m/s and 3.00 cm over the plate. At an Angle of incidence at the plate of 40°, the ripples turn towards the normal, to r = 22.7°. At 0° they bunch up but go straight on.
- (Core, then Supplement) Choose Gap. At 10 Hz the wavelength, 2.50 cm, matches the gap: Gap ÷ wavelength reads 1.0 and curved fronts fan out.
- (Supplement) Raise Gap width to 10 cm (ratio 4.0): most ripples carry straight on. At 1.0 cm (0.40) they spread almost in semicircles but are weaker. Set 5.0 cm, then lower Frequency to 5.0 Hz: the ratio falls from 2.0 to 1.0 and the spreading grows.
- (Core, then Supplement) Choose Edge: ripples curl into the geometric shadow. Lower Frequency from 6.0 Hz to 4.0 Hz and the longer ripples reach further in.